NEW FRONT ROTORS, CALIPERS AND LINES!!! (1980 Camaro, 2nd Gen Restoration)
HTML-код
- Опубликовано: 12 сен 2024
- Got rid of my old crummy front brakes. Front rotors, calipers, pads, and lines replaced! Nothing like NEW!!!
Front Brake Package: Power Stop: amzn.to/3D9HDA2
Front Brake Line: amzn.to/3wHrgsb
Super Clean Degreaser: amzn.to/3nkbjUt
Super Clean Aerosol: amzn.to/3ra3FP0
Thank you to:
Super Clean and OLSA TOOLS for providing the opportunity to check some of their products!!
If you need some tools or tool box accessories check out OLSA tools:
olsatools.com/...
You will receive 10% off your order!! Don’t forget to check out the you tube channel and subscribe.
Patreon: patreon.com/Th...
Instagram: www.instagram....
My RUclips Channel: / theshopworldwide
Merc!: teespring.com/...
A brand and RUclips channel, focusing on people that enjoy working on their own projects on their own time.
I recently installed the same calipers and brakes on my Firebird. I used a clip on the brake pad that sits on interior of the caliper. I noticed that you didn’t use one.
I can’t remember if it was in the kit or not……
Sorry, but that's not the way to install the caliper and pads. You don't hang the pads over the rotor and then try to put the caliper over them. The pad to piston spring wasn't even installed. Load the pads into the caliper first including the pad to piston spring. Then slide the assembly over the rotor. There are other details that needed to be done too. Best to read the factory service manual for your car before doing this work.
The service manual specifies a torque on the castle nut while spinning the rotor before backing it up. Your fingers will not seat the inner bearing properly.
As stated you didn’t even put on the spring on the inner pad that snaps into the piston hole. FWIW your suppose to put the pads in the calliper first on 1st and 2nd Gen Camaros. Your calliper is not a Bear or Wilwood! Those are the types you slide in the pads once the calliper is on the calliper bracket. Also apply brake grease to all sliding surfaces and O rings and pins.😮
Everything was retorqued after this video. Thanks for the info.
Amazing video!!! Great job explaining everything , thanks for this
Thank you!
I know that Amazon is known for not knowing what fits what, but when I see "It don't fit" I must ask questions. Is the link to the item on Amazon still accurate?
The normal way I do things from Amazon is I look up the parts on rock auto or cross reference the numbers between a few websites, always looking for the best price and that has the best or easiest return policy just Incase it is the wrong part or it’s damaged.
I just bought a 79 Firebird that has these same rotors and calipers. I seem to have to push the brake pedal down further that I should need to and just replaced the master cylinder. No Difference. You mentioned that the rotors have to go on a certain way which would indicate that they are side specific. If what you are say is correct about the slots starting at the center and pointing towards the rear, mine are on the wrong sides. Question; how did you determine the correct orientation and do you think it would cause the sort of problem I described about a soft-ish pedal? Brakes have all been bleed including the master cylinder. Is it worth the effort to switch sides?
I looked up everything I could on slotted rotors and all the manufactures stated to install them in that direction. My pedal is nice and firm. I’ve replaced everything except for the rear hard lines. I have zero complaints.
Brakes are always my first fix/upgrade on a new project. Everything else is second!
You have stop lol. These only had one working, so the system needed a revamp….
With the new brake hardware in the front, what was the result of it in terms of braking? Did the brakes improve the stopping distance over stock parts?
I haven’t done any actual testing on the brakes yet. As I build the car for the road/track I’ve been restoring and replacing. The cost of just stock parts compared to performance parts was not much more money. I know the brakes work great. The old brakes were trashed and needed replaced. When I get to do some testing I will do a video on it.
Those rotors are similar to stock size are you using stock wheels ?
They’re direct replacement. Same size and specs, calipers as well.
I am having trouble locating a bearing dust cap (grease cap) for my 1980 camaro. Do you know where I can buy one?
I’m not sure have you looked at classic industries?
I have. The one that is called out for 70 - 81 is too small. The 79 - 81 camaros had a larger outer bearing. The dust cap is a slight bit larger than the previous year models.