There is a plastic clip you have to remove on the top part of the bonnet latch on the A4-B9 model. I used a tiny screwdriver to pull back the plastic circlip. You can't just pull up on the knob. I was able to vacuum grass hoppers which had gone through the grill and made a mess. I just lifted out the top plastic piece and was able to clean behind the grill. Thanks a lot for this video. Most helpful.
Within the B9 from 2019 is the grille the same as the 2015-2018 model and just the ACC cover has been redesigned? At least the 2020 model got a different grille. I'm a bit confused about the differences of the facelifts from 2019 and 2020 and can't find a particular description which grilles are compatible with my 2019 B9...
I suppose these steps are going to be really similar to B9 A5? Also I would use plastic trim tools to disengage tabs to minimize scratches and surface damages, instead of screw drivers.
@@JamieWardVideos just inside the side of the bumper next to the fender, there’s 2 10mm nuts facing down in a little plastic bracket, if you just loosen those up a little bit, the bumper should pull out freely, not sure why he didn’t mention that step maybe his were loose
Great video... After you took off the bumper and detach the parking sensor wires. How did you take off the Parking sensors off the original grill and mount it on to the RS grill?
There is a plastic clip you have to remove on the top part of the bonnet latch on the A4-B9 model.
I used a tiny screwdriver to pull back the plastic circlip.
You can't just pull up on the knob. I was able to vacuum grass hoppers which had gone through the grill and made a mess.
I just lifted out the top plastic piece and was able to clean behind the grill.
Thanks a lot for this video. Most helpful.
I almost broke it off until I read this, thanjs
Thanks for that i couldnt open mine aswell
Is there a license plate attachment or bracket for this grill if needed?
very well explained. shown very precisely. Thanks for the video.
Greetings from Germany
Do the same/similar instructions to remove the bumper apply to the S5 Sportback? Thanks
Within the B9 from 2019 is the grille the same as the 2015-2018 model and just the ACC cover has been redesigned? At least the 2020 model got a different grille. I'm a bit confused about the differences of the facelifts from 2019 and 2020 and can't find a particular description which grilles are compatible with my 2019 B9...
Where did you buy the grill? Did it fit perfectly? As in did it have a place for your wires to attach and front camera...
I suppose these steps are going to be really similar to B9 A5? Also I would use plastic trim tools to disengage tabs to minimize scratches and surface damages, instead of screw drivers.
Do you know the PN code of the side air intakes that are fixed internally? To be clear where the third side screw is to be screwed
Thanks, you made it super easy 😁
2019 sline a4 looks same took all those screws clips out and bumper still stuck
Did you ever figure this out? same issue with my 2019, bumper is stuck around the headlights it seems
@@jvaglivelo Im looking to do this on my 2019. Did either of you figure it out?
@@JamieWardVideos just inside the side of the bumper next to the fender, there’s 2 10mm nuts facing down in a little plastic bracket, if you just loosen those up a little bit, the bumper should pull out freely, not sure why he didn’t mention that step maybe his were loose
Great video... After you took off the bumper and detach the parking sensor wires. How did you take off the Parking sensors off the original grill and mount it on to the RS grill?
any advice here?
can you provide a link where we can purchase the RS type grill ? thanks
mark KANG Yes, it is in the description.
Is this the same grill for the B9 S5 Sportback? thanks!
its2realj No the S5 is a different grille.
Can u do it without removing te wheels?
most likely yes by turning them to the opposite side you are currently working on.
Could it still able to connect the parking sensors on the new RS or S grille?