You are right my friend. Thank you so much for your support. See you into the forum for my next step, Arduino Due with DED and PFL ( i've also seen a video showing the air brakes indicator, it would be perfect for my cokpit). Regards
Have you started Deduino software prior to launch BMS? You have to first load the deduino code into your Arduino board (to be done just one time, then it will remain loaded in yoyr card). Prior to run BMS you have to Run Deduino software app. Just select com port and click on start. It should work
@Giovanni Lombardi Is DED ready sign spouse to be stay on the screen ? Mine stays 3 sec and it doesn't show it anymore ! Is it possible to send me wiring diagram for oled to arduino ? Maybe I am doing something wrong about wiring ! My e mail is avg@live.com Thank you.
Hello Giovanni, very nice work! Can you please tell me the specifications of your lcd . I have one 20x4 but i think its small for the ded Screen. Thanks in advance..
@@patogn20 right, you just have to uncomment options you want and then load the code in your Arduino. I believe Mega is ok, you can check this in the code also, it is written somewhere what card are supported.
@@giovannilombardi2678 ok, but the config.h file is not in the library. Where do i have to put that file to make the code work? Or its just a copy paste inside the sketch?
Where did you get this screen and how much did it cost? I am planning to run an ICP and DED off of an Arduino mega with DCS. Any chance you could help me out?
Ciao Giovanni, ho visto il tuo link per acquistare il display e chiede anche il tipo di connessione....cosa si deve scegliere? Io ho una atmega 2560. Il display è molto simile se non uguale a molto visti su AliExpress..sono gli stessi? Tnk's
@@giovannilombardi2678 ciao, nel software F4ts con cui ho già provato dei gauges c'è anche la possibilità di uscire sul display ( spero basti questo x la compatibilità).x lo skecth non so come verificare 😐
Ciao, questo modello è compatibile se non uguale a quello che usi? i collegamenti son gli stessi?con il softwae f4ts la mia scheda la vede e dovrei solo collegare il display....se questo va bene it.aliexpress.com/item/32988134507.html?spm=a2g0o.cart.0.0.1e6c3c005dcj0d&mp=1
@@piergald5334 ciao. A quale modello ti riferisci? Non vedo nessun link. Io ho scelto di utilizzare Deduino per il DED, ho quindi acquistato uno dei display raccomandati. Una volta preso bisogna interrompere il contatto di un circuito e poi si puó collegare. Se vuoi ti do lo schema dei pin, ma per la Arduino Due. Per F4TS so che si puó collegare ma da wuel che so è meno fluido.
Way to go Giovanni, bravo! See? the forum actually worked. ;-)
You are right my friend. Thank you so much for your support. See you into the forum for my next step, Arduino Due with DED and PFL ( i've also seen a video showing the air brakes indicator, it would be perfect for my cokpit).
Regards
Mine says DED ready on oled screen but when I enter Falcon BMS cocpit it doesn't show anything please help !
Have you started Deduino software prior to launch BMS?
You have to first load the deduino code into your Arduino board (to be done just one time, then it will remain loaded in yoyr card). Prior to run BMS you have to Run Deduino software app. Just select com port and click on start. It should work
@@giovannilombardi2678Thanks for reply Giovanni. I did everything what you said but it does not work I dont know what is wrong.I think I am unlucky !
@Giovanni Lombardi Is DED ready sign spouse to be stay on the screen ? Mine stays 3 sec and it doesn't show it anymore ! Is it possible to send me wiring diagram for oled to arduino ? Maybe I am doing something wrong about wiring ! My e mail is avg@live.com Thank you.
@@kevincagla4895 hi m8. Shure! Do you use Arduino Duo?
Giovanni Lombardi Thank you very much 🙂
Hi, what arduino card are you using, and how do you make it to refresh to quick? I am using an Arduino Uno and its a little slow, thanks.
Hi! I use a Duo.
Hello Giovanni, very nice work! Can you please tell me the specifications of your lcd . I have one 20x4 but i think its small for the ded Screen. Thanks in advance..
Hi!
Check here www.buydisplay.com/green-3-2-inch-arduino-raspberry-pi-oled-display-module-256x64-spi
@@giovannilombardi2678 Thanks a lot buddy for the reply!!!
Wow
Awesome work! I have a question... where do i have to put the config.h file after uncommenting? Thanks!
All you have to do is load the entire code in your Arduino.
@@giovannilombardi2678 Thanks for the quick reply! No editing on the config.h then? I don't have a UNO, i have a Mega... should it work anyways?
I'm working with the fuel flow right now... dont have the DED oled yet
@@patogn20 right, you just have to uncomment options you want and then load the code in your Arduino. I believe Mega is ok, you can check this in the code also, it is written somewhere what card are supported.
@@giovannilombardi2678 ok, but the config.h file is not in the library. Where do i have to put that file to make the code work? Or its just a copy paste inside the sketch?
Very coll.
I am trying to do The same but using The Mega Arduíno and a standard 20x4 LCD display.
If someone can help. I thank you so much.
Where did you get this screen and how much did it cost? I am planning to run an ICP and DED off of an Arduino mega with DCS. Any chance you could help me out?
Hello, search on web Deduino. You will find all information regarding this project
Any chance you could help me out with the code and send some pictures? I am having a hard time with the Uno coding right now....
Hi. Have you downloaded all Deduino stuffs?
@@giovannilombardi2678 Yes I have.
I am receiving a ' "SerialUSB" was not declared in this scope" error. ' in the comms.h
I removed the comment for the Uno in the code under config.h
@@Warbirdguy1 yeah, sounds something is wrong. I'll post you some pics tomorrow
@@giovannilombardi2678 thanks a million! Maybe I will have it working before my event this weekend!
Ciao Giovanni, ho visto il tuo link per acquistare il display e chiede anche il tipo di connessione....cosa si deve scegliere? Io ho una atmega 2560. Il display è molto simile se non uguale a molto visti su AliExpress..sono gli stessi? Tnk's
Ciao! Io uso una Arduino Due, hai controllato nello sketch Deduino se la Mega è supportata? Non ricordo
@@giovannilombardi2678 ciao, nel software F4ts con cui ho già provato dei gauges c'è anche la possibilità di uscire sul display ( spero basti questo x la compatibilità).x lo skecth non so come verificare 😐
Ciao, questo modello è compatibile se non uguale a quello che usi? i collegamenti son gli stessi?con il softwae f4ts la mia scheda la vede e dovrei solo collegare il display....se questo va bene
it.aliexpress.com/item/32988134507.html?spm=a2g0o.cart.0.0.1e6c3c005dcj0d&mp=1
@@piergald5334 ciao. A quale modello ti riferisci? Non vedo nessun link. Io ho scelto di utilizzare Deduino per il DED, ho quindi acquistato uno dei display raccomandati. Una volta preso bisogna interrompere il contatto di un circuito e poi si puó collegare. Se vuoi ti do lo schema dei pin, ma per la Arduino Due. Per F4TS so che si puó collegare ma da wuel che so è meno fluido.
@@giovannilombardi2678 ciao, ho modificato il mio precedente messaggio...ora dovresti vedere il link 😃