Hello Paul.... Can you tell me what your elevator settings are set for your flaps? I was told it would need some up elevator to bring nose up during approach. Can you tell me your elevator settings for both take off flaps and landing flaps please.Thank you sir
You should use a 3 cell on your brakes only. Your issue might be what I had on my P-60 turbine version. I'm using the stock equipment however two cell 7.4v just did not work so I use 7.4 on my receiver, servos, gear however I upped my voltage on the brakes and now they work great now.
Couple things I’m wondering: was that white edf mount to big (wide) so you cut it at the top? What type and size of screws did you use to mount the edf with?
Appreciate all the info, I just bought this plane. I see you have a Spektrum 10 channel and an NX10, so your able to handle all the controls with 10 channels, I’m guessing by y harness on some of the controls? I have this same Spektrum setup. Again thank you!
Hi, yes I have a little bit of up elevator mixed with the flaps. The plane noses down with flaps deployed so you need to compensate for that or it will come in fast on final approach.
Good morning, I'm setting up an L-39 with a dx 20. What aircraft type did you use to get the rudder and nose gear to steer correctly. Can you share how you did your setup. Having issues figuring it out with the 2085 module.
Are you referring to aircraft type setting in the transmitter? That should be set to your wing configuration which for the L-39 is normal: 1-AIL 1-FLP 1-ELE 1-RUD. Are you using the MFC-2085-DR or an older 2085? The new DR has a separate nose-wheel servo port HS-06. It is already assigned to the rudder RX input and it follows that channel. You can reverse it and setup travel/subtrim independent of the RUD channel. The DR also has a nose wheel gyro you can turn on and it seems to work quite well to help tracking during takeoffs.
Hi paulZRC I have a 8ch spektrum receiver with the built in as3x/safe.I am getting a HSD 120mm T33.The T33 has the MFC-2085 controller in it, Will the 8ch receiver clash with the MFC-2085 controller?
Sure, when I get home later this week and measure what I ended up with. That jet has a thrust angle issue and I had to work a bit on the thrust-ele mix to get it right.
@@pzukowski1001 thanks Paul. I really do appreciate it. Let me know for sure and I will give you my email address to send you file setup from your radio, if you don't mind. I have been having a hard time getting in touch with the seller to get information on some of my questions. Glad I came across your channel. Jayson
@@jaysonfarmer157 Hi Jason, just checked, I am 10mm in fort of the book CG. I find the model lands better and does not balloon as much with that setting.
Paulz rc every thing works on my HSD 120mm T33 except the throttle! im using a spektrum ar8360t and i plugged in R12 and Aux6 on the MFC-2085.Could you tell me what i am doing wrong? Thank You sir
@@pzukowski1001 Thanks for the right answer.! more question paul.The wire from the esc is black and white.will i plug it into the bind port or the throttle port? is white at the top or the bottom. Thank you always sir!
@@pzukowski1001 Thanks again Mr Paul.i was expecting to hear 12 beeps to let me know the system is 12 cell set up but it did not give me 12 beeps but fan fiannally came to life.Bless you sir.
@@lwrandall not sure I understand. The plane did not come with the EDF. I bought the JetFan EDF with the HET motor as a set which has been balanced together.
@@pzukowski1001 sorry. I am referring to the bracket surrounding the front of the Edf. The shroud directs the incoming air into the Edf. You show it at 2:08 in your video. Thank you.
![OhGeesy x Lefty Gunplay - What It Iz [Official Music Video]](http://i.ytimg.com/vi/L0yzW9t2ixk/mqdefault.jpg)
I’m looking forward to getting this plane, love how the L-39 flies
It flies amazingly, you will like it
Hello Paul.... Can you tell me what your elevator settings are set for your flaps? I was told it would need some up elevator to bring nose up during approach. Can you tell me your elevator settings for both take off flaps and landing flaps please.Thank you sir
Nice setup and flight, you fly with Ricky and CPT Rick of the Master of the Wind, hope Ricky can make a recovery, Jeff in LA USA
You should use a 3 cell on your brakes only. Your issue might be what I had on my P-60 turbine version. I'm using the stock equipment however two cell 7.4v just did not work so I use 7.4 on my receiver, servos, gear however I upped my voltage on the brakes and now they work great now.
Couple things I’m wondering: was that white edf mount to big (wide) so you cut it at the top? What type and size of screws did you use to mount the edf with?
Appreciate all the info, I just bought this plane. I see you have a Spektrum 10 channel and an NX10, so your able to handle all the controls with 10 channels, I’m guessing by y harness on some of the controls? I have this same Spektrum setup. Again thank you!
Hi Paul,
Do you have to mix elevator with full flaps? Do you have to mix up or down elevator with full flaps?
Thanks,
Stefan
Hi, yes I have a little bit of up elevator mixed with the flaps. The plane noses down with flaps deployed so you need to compensate for that or it will come in fast on final approach.
Good morning,
I'm setting up an L-39 with a dx 20. What aircraft type did you use to get the rudder and nose gear to steer correctly. Can you share how you did your setup. Having issues figuring it out with the 2085 module.
Are you referring to aircraft type setting in the transmitter? That should be set to your wing configuration which for the L-39 is normal: 1-AIL 1-FLP 1-ELE 1-RUD. Are you using the MFC-2085-DR or an older 2085? The new DR has a separate nose-wheel servo port HS-06. It is already assigned to the rudder RX input and it follows that channel. You can reverse it and setup travel/subtrim independent of the RUD channel. The DR also has a nose wheel gyro you can turn on and it seems to work quite well to help tracking during takeoffs.
Great video, but for your future videos let the music off. Every body wont to hear the sound of your jet. Thank you for all the good information.
Hi paulZRC I have a 8ch spektrum receiver with the built in as3x/safe.I am getting a HSD 120mm T33.The T33 has the MFC-2085 controller in it, Will the 8ch receiver clash with the MFC-2085 controller?
Hi the MFC-2085 will work perfectly with any Spektrum receiver. I use AS3X in all my HSD planes.
@@pzukowski1001 Thank You very much PaulZRC i got the Ar8360t receiver.
How do you like the HRB lipos? Good power? How are they balancing at charge?
They are excellent. My charger balances them at every charge. Lots of power. Use them on all my big EDFs
Envious. Wish we could have a concrete runway!
beautiful jet and Maiden, might need reversable thrust ; )
Paul, is that your HSD L-39 that was filmed by Phillydee? If so, can you share your setup and cg? Thanks
Sure, when I get home later this week and measure what I ended up with. That jet has a thrust angle issue and I had to work a bit on the thrust-ele mix to get it right.
@@pzukowski1001 thanks Paul. I really do appreciate it. Let me know for sure and I will give you my email address to send you file setup from your radio, if you don't mind. I have been having a hard time getting in touch with the seller to get information on some of my questions. Glad I came across your channel.
Jayson
@@pzukowski1001 Hi Paul, was just checking back with you on this.
@@jaysonfarmer157 Hi Jason, just checked, I am 10mm in fort of the book CG. I find the model lands better and does not balloon as much with that setting.
@@pzukowski1001 Thanks so much Paul. Is there anything unique you had to do to your radio setup?
Paulz rc every thing works on my HSD 120mm T33 except the throttle! im using a spektrum ar8360t and i plugged in R12 and Aux6 on the MFC-2085.Could you tell me what i am doing wrong? Thank You sir
Plug the throttle directly into the RX. Don't run it through the MFC. It is reversed by default and setup for futaba
@@pzukowski1001 Thanks for the right answer.! more question paul.The wire from the esc is black and white.will i plug it into the bind port or the throttle port? is white at the top or the bottom. Thank you always sir!
@@leejimerson3354 black is ground white is signal. If you allign with the other black wires than it will work. It plugs into the throttle channel
@@pzukowski1001 Thanks again Mr Paul.i was expecting to hear 12 beeps to let me know the system is 12 cell set up but it did not give me 12 beeps but fan fiannally came to life.Bless you sir.
@@leejimerson3354 Also do a throttle calibration to make sure the ESC understands your RX throttle levels.
Hi Paul what battery charger do you use
I use ISDT chargers. Had them for years. Main power supply is SkyRC.
Paul where did you get the Edf motor? Thank you
Hi I bought it at turbines-rc.com. They are located in France but shipping is quite reasonable. They carry all the JetFan EDFs.
@@pzukowski1001 Did the plane come with the shroud around the motor?
@@lwrandall not sure I understand. The plane did not come with the EDF. I bought the JetFan EDF with the HET motor as a set which has been balanced together.
@@pzukowski1001 sorry. I am referring to the bracket surrounding the front of the Edf. The shroud directs the incoming air into the Edf. You show it at 2:08 in your video. Thank you.
Whats the take-off weight?
17.6lb
Look forward to flying with you at thunderbird field. Gary also bought the same jet. Lee