Setting Pump Compensator & Relief Valve
HTML-код
- Опубликовано: 11 сен 2024
- In this Hydraulic Tip we are using our Mobile Hydraulic Training Lab to demonstrate the proper way to set the Pump Compensator in conjunction with the system relief valve. Visit www.GPMHydrauli... to learn about our 2-Part Training Program.
Yes sir it's true someone turned the pressure above system relief valve and thanks once again
Best explanation on RUclips!
Excellent videos!
Everyone watching these MUST WEAR EYE PROTECTION! ALWAYS!
PLEASE🙏
May I also request safety be first and foremost. Equipment should be secured before adjusting anything. Often hydraulics hold something very heavy up.
Very nice!
thank my teacher
Superb sir . Very nice explanation.is it the same in the hydraulics pumps
Very interesting video!
thank you for sharing sir.
Good demo Thanks
Nice
Very nice. So what is best pressure set for roadblocker?
Don't know what a roadblocker is, but if it's hydraulic, the best pressure is the lowest one that will do the job.
Simple and straşght forward
I follow on the procedure however I have a trailer that has the pump submerged in the reservoir with a Honda engine on top.
Kinda like a big ice cream machine with paddles inside it that run via hydraulics.
I'm having to replace the pump. What would the adjustment procedure be for the new one?
Thanks for your question! Is this a submerged pressure compensating pump? Usually, the only way to set one of those is on a test bench, but you can usually order it preset to the desired pressure. Of course, if it is a fixed displacement pump, you need only set the relief valve, which should be external.
Good morning
What if i hve a load sensing pump and no load sensing signal is connected to it that case load sensing screw should be fully tightened or fulley loosened? Or what will be its tightening and loosening affect on output pressure
Thank you for your question! The load sensing adjustment can be left at its factory setting if you like - as long as there is no sensing line attached, there is no need for adjustment. However, if you would like to disable it entirely to avoid "knob turner" issues, it can be fully tightened to ensure that only the compensator adjustment will affect the pressure. Just be sure that anyone who may be adjusting it is aware of the correct setting to adjust, perhaps a warning note on the pump.
@@JackWeeks thank-you so muchh sir!
One more thing i wanna say is that it will be very helpful if you will make a vid on how to do null position setting for moog servo valves generally which are generally used in 6hi rolling mills😊
help me fix, or ajust my 2speed catapiller.. I wanna make it go faster..
Can too much pressure damage the pump?
It certainly can! Always be aware of the design limits - download the specs from the manufacturer if you don't have them, and keep a nice cushion below the max rated pressure.
What is the minimum pressure I can set with a pump?
I would imagine 0 PSI would be the minimum. But it would depend upon the particular pump. For instance, some pumps have both minimum and maximum stroke limiters, so for that reason, must be idled using a tandem or open center directional valve that will unload the pump at idle,
Hi, we have a similar unit. Initially, there was a leak problem
but still working. When we had the leak sealed, there is no pressure
build up. So we tried doing what you had shown in this video, but still
no pressure buildup. Hope you can help us.
JAYSON PENDON Hi, thanks for your comment! If there is no pressure building, that means there is no resistance to your flow. Fluid is returning to tank somewhere it shouldn't. The most likely culprit is a valve somewhere stuck open and providing a flow path to the reservoir. Hydraulic oil will always take the path of least resistance, so determine where the oil is going. A good tool for this is a thermal imaging camera, but you may need to install a flow meter, moving it to different lines until you find which one is dumping oil. Good luck in your troubleshooting!
Why didn't the pressure drop when you opened the needle valve at the end.
Thank you for your response! The pressure didn't drop because the directional valve downstream was closed. In this particular case, a closed center directional valve was used, so strictly speaking, the compensator and relief could have been set without closing the needle valve. We recommend that it be closed because so many different configurations are out there and someone may be using this video who has, for instance, a tandem center valve rather than the closed center valve in the demo system shown.
@Jack Weeks Thank you for the reply!
So I have a vickers p.c pump and have it set to 1k psi. Relief is at 1300 or so.
Are vickers pumps always noisy? If I dial the pump down to say 500psi it's a lot less noisy.
Also, prime mover is maxed out at 50 amps when I have it set to 1000psi. Can that attribute to pump noise?
3 phase motor, data plate says 50 amps max.
It's on a bagging machine, feeds product into bag, then presses it down, seals it etc.
When the comp pump hits set pressure, it's maintaining set pressure so should the motor always pull x amount of amps?
Thanks so much again.
@@JackWeeks I wish I had a flow meter so I could do some math to see what hp is required.
@@bucksnortbumblefuk6872 A higher pressure will indeed contribute to noise, but it shouldn't be excessive. There may be some other issue as well, such as an air leak or blockage in the suction line, or worn bearings, depending on the sound it is making.
The current draw of the drive motor will not be constant even though the pressure is maintained. Current will also change based on speed and load resistance as those change.
@Jack Weeks pump is new, but guy before me was cavitating it bad as i started my repairs with fixing the inlet/supply. Several fittings loose. Also there is a 90* bend in front of the pump I don't really like.
Thanks again for the reply.
Asif Khan sogan odra
How bar set
If your gauge measures pressure in Bar rather than PSI, the conversion factor is 1 Bar = 14.7 PSI (at sea level).
hello