Thank you so much I put dishwashing liquid in and the flood sensor went off on both drawers after following your first instructions and removing bottom drawer and lightly wiping the sensor hey presto both drawers are working thanks for saving me $200 bucks mate your a champion
matt mogan - omg! What I did to our dishwasher juz now and I can’t figure it out! So I juz turned d main switch off and left the house to unwind huhu. While driving , I thought of watching RUclips! I’m going back home now! Haha! Will keep posted !
I have been away for 3 months so dishwasher was not used but remained connected to mains power; 3days following my return but still not using the washer, the beeping noise and F1 fault on the display appeared. I cycled the power with about 1min delay and it was all good for about 20 minutes then F1 returned with beeping. This time I have recycled the power again but I set it on the 7min rinse cycle. No problems after that.
when i press the 2 buttons -start and lock - i get a a numbers countup -then F1 + that loud noise CAN YOU HELP PLEASE there is no water in around actuator switch/sensor
Thank-you for posting this video, very helpful, took me a while to figure out how to get to the diagnosis mode, I found I had to hold down lock button for a second before the pause/start button. Also had to look elsewhere to find out how to remove drawer by pressing in plastic clips as this was not shown in the beginning of your video. Thanks again
Thank you so much I put dishwashing liquid in and the flood sensor went off on both drawers after following your first instructions and removing bottom drawer and lightly wiping the sensor hey presto both drawers are working thanks for saving me $200 bucks mate your a champion
matt mogan - omg! What I did to our dishwasher juz now and I can’t figure it out! So I juz turned d main switch off and left the house to unwind huhu. While driving , I thought of watching RUclips! I’m going back home now! Haha! Will keep posted !
ybur blue good luck buddy
matt mogan - can’t open the drawer tho! Huhu I will end up calling d service provider . Sigh 😔
BAM! Thank you so much for this upload, I dried the base and let is sit there awhile to make sure and it all works now :)
Thanks man you repaired all my dishwasher
Thanks heaps, still valid info 5 years later.
I have been away for 3 months so dishwasher was not used but remained connected to mains power; 3days following my return but still not using the washer, the beeping noise and F1 fault on the display appeared. I cycled the power with about 1min delay and it was all good for about 20 minutes then F1 returned with beeping. This time I have recycled the power again but I set it on the 7min rinse cycle. No problems after that.
Very helpful! Thanks so much!
Lots of useful info, thank you.
Very helpful, my problem is solved.
How the heck do I remove it, it won’t come out
Thanks!!!!!!
when i press the 2 buttons -start and lock - i get a a numbers countup -then F1 + that loud noise
CAN YOU HELP PLEASE
there is no water in around actuator switch/sensor
Mine had been doing this for 4 days.. Power button had nothing to do with this.
how do you remove lower draw,mine is stuck.
what if both draws have the F1 code?
What causes the f1 fault code
Try turning off at wall. Wait 3 seconds. turn back on. Should reset it's computer :)
Hahahahaha nope
That is my problem please someone respond fast
what a shit dishwasher
sorry hear that. This is help video not sale pitch.
We've had ours for 16 years. still working fine.
Utter nonsense
Thank-you for posting this video, very helpful, took me a while to figure out how to get to the diagnosis mode, I found I had to hold down lock button for a second before the pause/start button. Also had to look elsewhere to find out how to remove drawer by pressing in plastic clips as this was not shown in the beginning of your video. Thanks again