I can't wait to try this! My mechanic assumed gearbox problem 3 years ago....... And I have been holding off waiting for clutch to go # T5 camper 2.5 130bhp has been running like a dream/ rocket ship with king size bed otherwise 😁
My man, I am a mechanic, but spend most of my time working on other peoples stuff so for my own cars get neglected sometimes, this is real helpful because it saves me a lot of time, thank you Bruv all the way from Australia 🇦🇺🤙🏾🤙🏾
Quick question at 4:51 when he says "let the gearstick go to rest" is that in neutral position or in 2nd gear? I have slight resistance/grind when pulling away in 1st and changing into 2nd gear, all other gears fine and also perfect when changing down the gears until 1st which is harder to get in. Is this likely to help my issue? Thank you in advance.
This is a very helpful video thank you as mine was struggling to go easily into first gear sometimes, but it is missing a few bits of information. You should also have a black plastic cover up above the peddles that also needs to be removed before you can undo all of the screws for the large grey plastic cover. I would strongly recommend marking the silver linkage rod (below the yellow plastic adjuster) at its top of travel and bottom of travel with a marker per before you try and adjust it so that you know where it was and where to put it back to if you need to - you can make a pigs ear of its adjustment quite easily and it seems to ratchet in about 1 or 2mm increments. As others have said the yellow clip breaks really easily so try not to bend it more than necessary and you don't need to clip it back in place each time to test the adjusted movement of gear lever - it has a left clip and a right clip. There is also a second rod with its own similar mechanism and adjuster that is much harder to get to - I'm guessing this does the other plane of adjustment but I didn't adjust it - it looks quite tricky to do and you might make a real mess of the adjustment - if you are going to adjust this one as well then it would probably be best to get the first one set as best as possible then do the second one and also mark its position before you start.
I had to change the gear selector on my gearbox yesterday. Now my gears are all out slightly 1st is where 3rd used to be. And it goes into reverse without lifting the licking mechanism. I think my side gate cable needs adjusting. Im a bit confused by how you did yours. The manuals Ive read, say to have the gearbox in second gear and the gear stick has 2 holes for a 6mm pin that lock it in the 2nd gear position. Yours just seemed to be in neutral when you set it..... Did you just rely on the stick self centering between 3rd and 4th? Not trying to be smart, I just really dont want to cock this up👍
Great video! I have just had a new clutch kit and dmf on my 08 T5 2.5. 1st 2nd 3rd 4th ok then try to put it in 5th and it's a little stiff. Could this be the same thing? Any info would be great? 🙏
Hi i have a 2006 t5. I have to let the clutch up about 1 inch from the floor to get the gear stick to slot into 6th. Every other gear seems ok any idea what might be wrong?
The most common cause of gear shift problems is low oil level check the gear oil first. After that is correct if it does not improve. Then next I would suggest it could be the 6 gear bearing which is a gearbox out job so I would resurch a garage nearby and check for reviews before committing the job to the for peace of mind Hope this helps
Same thing happened to me, Followed his advice and the plastic clip snapped off. Sadly this chap doesn't seem to give advice, now I have a bigger problem than before!
Rich Call My problem turned out to be the cables. The one that moves forward and back. The outer had cracked The cable kit didn’t include the ball joint parts with the plastic clips ( so they must be separate parts). I managed to change the cable myself. The hardest thing was clipping the cable to the gearbox from underneath.
I can't wait to try this!
My mechanic assumed gearbox problem 3 years ago....... And I have been holding off waiting for clutch to go
# T5 camper 2.5 130bhp has been running like a dream/ rocket ship with king size bed otherwise 😁
My man, I am a mechanic, but spend most of my time working on other peoples stuff so for my own cars get neglected sometimes, this is real helpful because it saves me a lot of time, thank you Bruv all the way from Australia 🇦🇺🤙🏾🤙🏾
Thank you so muchfor the video.
Yesterday i couldn't put first gear. And after watching this 10m it pas fixed. So happy...
Thank you...
Quick question at 4:51 when he says "let the gearstick go to rest" is that in neutral position or in 2nd gear?
I have slight resistance/grind when pulling away in 1st and changing into 2nd gear, all other gears fine and also perfect when changing down the gears until 1st which is harder to get in. Is this likely to help my issue? Thank you in advance.
Brilliant mate - Worked a treat on my T5 (2011). Thought I had a gearbox issue but you solved it :-)
This is a very helpful video thank you as mine was struggling to go easily into first gear sometimes, but it is missing a few bits of information. You should also have a black plastic cover up above the peddles that also needs to be removed before you can undo all of the screws for the large grey plastic cover. I would strongly recommend marking the silver linkage rod (below the yellow plastic adjuster) at its top of travel and bottom of travel with a marker per before you try and adjust it so that you know where it was and where to put it back to if you need to - you can make a pigs ear of its adjustment quite easily and it seems to ratchet in about 1 or 2mm increments. As others have said the yellow clip breaks really easily so try not to bend it more than necessary and you don't need to clip it back in place each time to test the adjusted movement of gear lever - it has a left clip and a right clip. There is also a second rod with its own similar mechanism and adjuster that is much harder to get to - I'm guessing this does the other plane of adjustment but I didn't adjust it - it looks quite tricky to do and you might make a real mess of the adjustment - if you are going to adjust this one as well then it would probably be best to get the first one set as best as possible then do the second one and also mark its position before you start.
Nice one chap😎
can't imagine who wouldn't like this.
Great video thanks for shareing
Thanks I have just fixed mine nice and smooth now.. but the plastic part that bends back is so cheap and fragile!!!nearly broke off
Thanks great advice top man.
Merci pour cette vidéo très utile. 👍
I love it; - pedal cluster! 😂
Hi. Great vid. Mine, T5 2006 appears to have that tab broken off. Any idea of a part number for this? What it is called?
Heyy✨ have you found out?
I think it is a new cable i got one from Arnold Clark Autoparts BKG1255
I had to change the gear selector on my gearbox yesterday. Now my gears are all out slightly 1st is where 3rd used to be. And it goes into reverse without lifting the licking mechanism. I think my side gate cable needs adjusting. Im a bit confused by how you did yours. The manuals Ive read, say to have the gearbox in second gear and the gear stick has 2 holes for a 6mm pin that lock it in the 2nd gear position. Yours just seemed to be in neutral when you set it..... Did you just rely on the stick self centering between 3rd and 4th? Not trying to be smart, I just really dont want to cock this up👍
Hi Luke, my gear stick is quite clunky/sloppy not tight. do I need to a new gearbox or is there something I can check.
Thank you . Its help me alot. But what if only gear 2 hard to shift. I need drive really slow as 10km/h to shift gear 2. My van nissan urvan e25.
Thankyou I have the same problem
Hi good video ,I’m having trouble with reverse gear ,doesn’t feel it’s going right in and jumps out, any ideas
Great video!
I have just had a new clutch kit and dmf on my 08 T5 2.5. 1st 2nd 3rd 4th ok then try to put it in 5th and it's a little stiff.
Could this be the same thing?
Any info would be great?
🙏
You're helpful.
Hi my vw is a 6 speed and 3rd gear is sticking I tried this and it didn't work do you have any advise
mine will go into 5th gear but won't come out of 5th when the van is going slowly or stopped,but comes out when moving at speed ?
Hi i have a 2006 t5. I have to let the clutch up about 1 inch from the floor to get the gear stick to slot into 6th. Every other gear seems ok any idea what might be wrong?
The most common cause of gear shift problems is low oil level check the gear oil first.
After that is correct if it does not improve.
Then next I would suggest it could be the 6 gear bearing which is a gearbox out job so I would resurch a garage nearby and check for reviews before committing the job to the for peace of mind
Hope this helps
Hi my t5 won't go into 2nd and 4th all the time sometime it goes in fine then other times it's like it's nutrial any ideas
Does this work if for reverse if it keeps poping out ?
Wonder the same
Me too, did you get fixed
@@MrGixxercrazy1 sold it ,thanks though
Luke i see the problem the steering wheel is on the wrong side of the car.😁 who is that guy is it Seymour 🤣🤣🤣 ask your dad
The right side table
hi thanks every thing was going good until i tried to snap back the yellow clip and it snapped is it easy to fit a new one cheers
Same thing happened to me, Followed his advice and the plastic clip snapped off. Sadly this chap doesn't seem to give advice, now I have a bigger problem than before!
The righthand side
Can this be why my van won't go into 3rd gear??
Hi Rich I have the same problem with 3rd. Have you fixed yours?
@@pippashaw8224 hi, my van will go into 3rd but no drive. Its going in next week to have gearbox strip down. Fingers crossed.
Rich Call My problem turned out to be the cables. The one that moves forward and back. The outer had cracked The cable kit didn’t include the ball joint parts with the plastic clips ( so they must be separate parts). I managed to change the cable myself. The hardest thing was clipping the cable to the gearbox from underneath.
👍++++🔔
Anyone else managed to brake the plastic clip😞
I have the yellow ball socket pivot broken, any help where I can find one?