Thank you very much for doing this video. Just installed the module and it solved so many transmission issues and the P,N and RPM, and Ikey system error and more
@@teewild290 little gift for you, use nitrogen to fill your tires, few PSI will do. Available for free at Costco tire center. It will prevent losing air in tires, especially when temperature changes. Can't thank you enough God bless!
Got the same issue 2014 pathfinder. Same exact I key and b tcm dtcs. Was going to get the tcm reprogrammed but now I’m going to do what you did. Thanks a lot man. Godbless
a little gift for you, use nitrogen to fill your tires, few PCI is enough in each tire, available at Costco Free , it will prevent losing air in your tires when temperature changes, it works. Thank you again!
Good evening, I have this problem, the P and N do not appear. I cannot accelerate much because I can only reach 2000 RPM and 40 miles. Then she forces herself and I can't go any further. todayFriday my TCM arrives. I hope that could be the problem. because the P and N do not appear on the board. Seeing your video gave me hope that it is the damaged TCM. greetings and blessings. greetings from Mexico buenas noches, yo tengo ese problema, no me aparece la P y N. no puedo acelerar mucho porque solo puedo llegar a 2000RPM y 40millas. luego se forza y no puedo pasar mas. hoy viernes me llega mi TCM. espero pueda ser ese el problema. porque no me aparece en el tablero la P y N. al ver su video me dio una esperanza que sea la TCM dañada. saludos y bendiciones. saludos desde mexico
Sorry im late but also make sure your catalytic converter is not plugged, If i wont go past 2000rpm in park. Transmission itself can be a problem if the belt pulleies in the transmission is binding at a certain gear. This one i had to replace both tcm and cvt transmission.
Wasup man great video short and understandable explanation. Quick question 2013 altima 2.5 got that B2604 code no P or N in the dash indicator like yours and shifts a little hard not too bad going into D or R but otherwise drives great. So I should replace TCM?
I’m still getting neutral and when I put it in drive it says drive sport neutral shows drive, reverse shows neutral, and park shows reverse and when I play with the shifter a bit it goes back to normal and reverse and park put me in reverse could this still be the issue though.?
Hi brother i have b2603 shift position code and i have same i key system error message and the gear shift sometimes not moving when I start the car only when I push the small button to release it.
That floor shifter solenoid could be the problem when the brake pedal is depressed you supposed to feel a little click eat time. I have had some go out with spills and weak solenoid. The bcm somehow monitor both unit tcm and that
Ebay I bought mine from.the junkyard yes if they have those models laid out there. No you good bro. No u Don't have to write it if u bought a used one. New one from dealer u will have too.
It is mine, it is an altima 2008, it brings the suich inside in the cvt it gives me the code in bcm of suich pnp I put another tcm it is not the same numbering it is different and it deletes it but it marks me suich of position I do not remember the code but with Those other tcm no longer mark me or PN D. and with yours, which is numbered 16, it does not mark me neither P nor N as well as your case, my question is will the suich that goes inside or the tcm? why when I put P or N of the gearbox to the tcm if there is a signal like in the other speeds
Ok yea on the 08 the internal set up is different from the 2016 model. Yea the tcm display the PRNDL on the dash display. If tcm is new like bought from dealer or else where, it has to be programmed because those are blank and will do the same thing and will not shift.
@@miggyspain3218 it's that code keeps setting off replace the TCM. Does it show park on the display like in my video?. Whic car u working with same car?
@@teewild290 the werid thing is that light never show up on the dash but there a weird noise going on whenever I switch "gears" so I used a scan tool and thats the code that showed up b2604 PNP switch. Maybe its starting to go bad ?
Pnp switch is on top of the transmission right where the shifter lever is bolted on. Tcm is bolted next to the ecm by battery the small, single connected module
I am having this exact issue with my 2013 Nissan Altima. It looks like I need to replace the TCM to fix everything.
Thank you for posting this video!
You welcome
Thank you very much for doing this video.
Just installed the module and it solved so many transmission issues and the P,N and RPM, and Ikey system error and more
You welcome bro
@@teewild290 little gift for you, use nitrogen to fill your tires, few PSI will do. Available for free at Costco tire center. It will prevent losing air in tires, especially when temperature changes. Can't thank you enough God bless!
Got the same issue 2014 pathfinder. Same exact I key and b tcm dtcs. Was going to get the tcm reprogrammed but now I’m going to do what you did. Thanks a lot man. Godbless
No problem man :)
a little gift for you, use nitrogen to fill your tires, few PCI is enough in each tire, available at Costco Free , it will prevent losing air in your tires when temperature changes, it works. Thank you again!
Good evening, I have this problem, the P and N do not appear. I cannot accelerate much because I can only reach 2000 RPM and 40 miles. Then she forces herself and I can't go any further. todayFriday my TCM arrives. I hope that could be the problem. because the P and N do not appear on the board. Seeing your video gave me hope that it is the damaged TCM. greetings and blessings. greetings from Mexico
buenas noches, yo tengo ese problema, no me aparece la P y N. no puedo acelerar mucho porque solo puedo llegar a 2000RPM y 40millas. luego se forza y no puedo pasar mas. hoy viernes me llega mi TCM. espero pueda ser ese el problema. porque no me aparece en el tablero la P y N. al ver su video me dio una esperanza que sea la TCM dañada. saludos y bendiciones. saludos desde mexico
Hi bro.
Can you tell me about the results of what happened to your car after the installation of the new TCM please?
Best regards.
Sorry im late but also make sure your catalytic converter is not plugged, If i wont go past 2000rpm in park. Transmission itself can be a problem if the belt pulleies in the transmission is binding at a certain gear. This one i had to replace both tcm and cvt transmission.
Results were good. The P and D shows back on the display and that judder code pf-- i cant remember disappeared too and drove great.
@@teewild290 Sounds good
Thanks bro.
Hola amigo quedo con eso tengo el mismo detalle
.....need the same tcm number oem?
Wasup man great video short and understandable explanation. Quick question 2013 altima 2.5 got that B2604 code no P or N in the dash indicator like yours and shifts a little hard not too bad going into D or R but otherwise drives great. So I should replace TCM?
If u getting that's exact same symptoms like this one yes. This one has that one hard shift it will drive fine all day. But the TCM was no good
@@teewild290 okay ima do that brotha I appreciate the quick response 🙏🏼
@@alexquezada510 no prob ❤️
Did u have to get the new one programme9?
👌👌👌👍👍
I’m still getting neutral and when I put it in drive it says drive sport neutral shows drive, reverse shows neutral, and park shows reverse and when I play with the shifter a bit it goes back to normal and reverse and park put me in reverse could this still be the issue though.?
Yours maybe out of adjustment check the nut of the transmission where the cable attaches. Also stretch cable could be the issue too
Will a bad TCM stop your Altima from pulling? Going into gear?
It should still move but it will not variet the gears, if it won't move u have a mechanical/hydraulic issue
Hi brother i have b2603 shift position code and i have same i key system error message and the gear shift sometimes not moving when I start the car only when I push the small button to release it.
That floor shifter solenoid could be the problem when the brake pedal is depressed you supposed to feel a little click eat time. I have had some go out with spills and weak solenoid. The bcm somehow monitor both unit tcm and that
Was it ever intermittent? Im having the same issue on a 2017 sentra and cant find a wiring diagram
This one was consistent alldata.com is the best resource to get it it's cheap online to by the book to really get everything u need
Question where u located....I think u sold most of my problem....u are appreciate.
Solved? Lol I'm in ga
Hey sorry to bother u. Where can I get a tcm from? Ebay or dealer or junkyard? And do I have to get it program or reprogram?
Ebay I bought mine from.the junkyard yes if they have those models laid out there. No you good bro. No u Don't have to write it if u bought a used one. New one from dealer u will have too.
It is mine, it is an altima 2008, it brings the suich inside in the cvt it gives me the code in bcm of suich pnp I put another tcm it is not the same numbering it is different and it deletes it but it marks me suich of position I do not remember the code but with Those other tcm no longer mark me or PN D. and with yours, which is numbered 16, it does not mark me neither P nor N as well as your case, my question is will the suich that goes inside or the tcm? why when I put P or N of the gearbox to the tcm if there is a signal like in the other speeds
Ok yea on the 08 the internal set up is different from the 2016 model. Yea the tcm display the PRNDL on the dash display. If tcm is new like bought from dealer or else where, it has to be programmed because those are blank and will do the same thing and will not shift.
I’m having a similar problem with my Altima, does the new tcm you put in need to be reprogrammed by an expert or can I do the battery truck?
Trick^^
Nice
does it have to be with the same numbering?
Yes or close
Was it shifting hard with the bad tcm?
If R,or D was selected it banged into gear but drove smoothly after that
Is.this the the b2604 code? How hard is this to fix?
How expensive was.the piece
Thanks in advance!
I'm sure it is. Do it say that code in the BCM PNP switch?
@@teewild290 yes its says its the PNP / clutch switch
@@miggyspain3218 it's that code keeps setting off replace the TCM. Does it show park on the display like in my video?. Whic car u working with same car?
@@teewild290 the werid thing is that light never show up on the dash but there a weird noise going on whenever I switch "gears" so I used a scan tool and thats the code that showed up b2604 PNP switch. Maybe its starting to go bad ?
Its a nissan altima 2012
Are used TCMs plug and play?
Yes.long as they match
where is the pnp switch I have the same then changing the tcm remains?
Pnp switch is on top of the transmission right where the shifter lever is bolted on. Tcm is bolted next to the ecm by battery the small, single connected module
2016 bad tcm wtf too new
Hey, can you send me an email address or a whatsapp number where i can contact you? I have the same exact issue with my Nissan X-Trail T32 Hybrid.