Eccellente! hai meritato la mia iscrizione al canale, sai spiegare senza parole.... un concetto che altri hanno reso complicato con i tecnicismi .....Ma per chi come me, che non ho studiato queste robe, non gli servono i lati tecnici, ormai nel semplice fai da te, si fa il copia e incolla per le cose elementari, ovviamente poi se si è in grado di comprendere i lati tecnici, a quel punto si è in gradi anche di insegnarli, quindi si elude lo scopo dei video. Volendo fare un esempio: un costruttore di automobili darà il libretto di istruzioni e manutenzioni di base, non il libretto di dati tecnici e manutenzione per l'officina riparazione, penso di aver reso l'idea, ovviamente sto rispondendo a tutti gli altri canali che per un concetto simile hanno dedicato anche oltre 15 minuti di lato tecnico. Se potevo mettere 5 like lo avrei fatto, complimenti davvero!👌💯
Senza offesa a parte che è collegato tutto correttamente, ma l'alimentetore che hai usato dovrebbe gia avere l'uscita in CC, il filo bianco dovrebbe essere il + e il nero il -, raddrizare ulteriormente la tensione non serve a niente a parte introdurre una caduta sul ponte, ma compensata dal condensatore. Devi usare un trasformatore normale se vuoi che serva a qualcosa.
that's true and thanks for that but the problem here was.... When you measured the output with the DMM IT WAS NOT CLEAR ON YOUR DMM IF YOU WERE MEASURING V AC or V DC all we could see was a cheap , no name multimeter that was showing 15.3 V but we couldn't actually see the setting now.. yes common sense dictates that a bridge rectifier with a smoothing capacitor will produce DC Output but... THIS IS A TUTORIAL and you didn't show that very clearly your wave shape video was a lot better , in my opinion i mean for the kiddies that don't know how it works, it's always better to have a scope to show it and in my opinion it's much better to first show Half Wave Rectification (so they understand how the negative half of the wave is removed) and then to see a pulsating DC without the inverted rectified waves and to also show them the power loss through a diode. then ......you bring in the bridge rectifier so that the purpose is made clear - that we get the inverted portion of the wave on the positive cycle - that we don't lose half our power in rectification - and that the capacitor acts as a smoothing cap to smooth out the pulsating DC but again, you didn't make this clear
Это не щедевр, а как любят делать иностранны показуха, он ничего не поднял просто конденсаторы заряжаются до амплитудного значения напряжения, а на коропбе указана номинальное, судя по конденсатору который он вставил туда при первойже нагрузке напряжение просадит и устройство будет работать не корректно
Hello sir I have a question , I'm connecting 3x3 piezoelectric sensor and produced at around 9v how can I use tranformer and how do I connect? Also I have another question I have connected rectifier to ac o/p of piezoelectric sensor and produced some volts but even after getting the o/p at the capacitor if I connect Dc to DC booster it is not working which is not giving o/p
how does that capacitor rating relates to voltage out put? Im mostly interested to build magnet alternator so Im curriuse to know how its voltage regulator build or current cutt out if baterry reaches centrain Ah charge .
No it hasn't the Adapter output was 9V AC the primary input was 240 V AC it didn't convert to DC he was basically using it so that he didn't have to manually step down the V AC from there he basically just rectified the AC and smoothed it out with a cap.
Can that circuet be used with alternator? I want some thing to build for me ignition coil useing seperate rectifier and tap in those 3 phase windings on the alternator but Im woried about me lead acid baterry if it wuld explode . So I dont realy have negative on the coil be me its e core type ignition coil with 4 pin gm ignition module . So can the coil and those rectifiers you show with 4 pin gm ignition module have seperate grounding? To not interfeare with baterry ore the altrnator voltage potential? In the past I did try out hv ceramic capacitors on me ignition coil evry thing was great except the alternator its starting charge from 1200rpm goes up to 3000rpm that was problem for me . So please any circuets that can protect ground reference voltage and protection please.
Ciao, sul citofono ho una lampadina a 12 volt vorrei mettere una a led sempre da 12 volt il tuo circuito va bene? devo comunque sempre mettere il condensatore?Grazie
Learn how FULL WAVE RECTIFICATION WORKS Learn the steps - do it on an Oscilloscope for yourself - Take readings before Conversion - Learn what Half Wave Rectification is and how it works - Learn what a full bridge rectifier is - Learn how it works - make a model and test take readings - Send and AC Signal into a Bridge Rectifier WITHOUT A CAPACITOR on the output, Look at this through an Oscilloscope and see what you get - then put on the cap, and see what you get Basically the answer to your question lies in Understanding AC and DC and Wave Rectification if we just tell you the answer, you're going to keep saying BUT WHY, ok you need to test a few things and look up a few things and understand some fundamentals does that help you understand it ?
Well if that is the case then they miss labeled the case also because a powersupply would be converting ac to dc and a transformer steps ac voltage up or down. I thought the ac symbol was the miss labeled item as ac 220 to 9v are not as common as they use to be.
claro el transformador es de corriente alterna a corriente alterna,un reductor,pero es alterna 9 volts...generalmente esos transforma a corriente continua x eso la confusion.....
Eccellente! hai meritato la mia iscrizione al canale, sai spiegare senza parole.... un concetto che altri hanno reso complicato con i tecnicismi .....Ma per chi come me, che non ho studiato queste robe, non gli servono i lati tecnici, ormai nel semplice fai da te, si fa il copia e incolla per le cose elementari, ovviamente poi se si è in grado di comprendere i lati tecnici, a quel punto si è in gradi anche di insegnarli, quindi si elude lo scopo dei video. Volendo fare un esempio: un costruttore di automobili darà il libretto di istruzioni e manutenzioni di base, non il libretto di dati tecnici e manutenzione per l'officina riparazione, penso di aver reso l'idea, ovviamente sto rispondendo a tutti gli altri canali che per un concetto simile hanno dedicato anche oltre 15 minuti di lato tecnico. Se potevo mettere 5 like lo avrei fatto, complimenti davvero!👌💯
That is an absolutely savage way to strip a wire.
Pero sin necesidad de poner puente rectificador la salida ya esta rectificada ya tienes un (+) y un (-) 👍
Ta pendejo
Si es verdad ya tiene la plaqueta de rectificación
Terimakasih suhu ilmunya ,semoga berkah.
اززحماتتون بسیارمتکرم👍🏻🙏🏼
You too, friend
🇮🇩🎀sukses dan sehat slalu 🎀🇮🇩👍👍👍
c'est très bien pour l'explication
Senza offesa a parte che è collegato tutto correttamente, ma l'alimentetore che hai usato dovrebbe gia avere l'uscita in CC, il filo bianco dovrebbe essere il + e il nero il -, raddrizare ulteriormente la tensione non serve a niente a parte introdurre una caduta sul ponte, ma compensata dal condensatore. Devi usare un trasformatore normale se vuoi che serva a qualcosa.
Watching and sending support nice sharing
Electro Boooom would say, FOOOOOOOOOOOLLLL BRRRRRIDGEEE RECTIFIERRRRRRR !!!!!!
Actual voltage of the adapter is 11v AC not 9v. You can see waveform here : ruclips.net/video/8WPJ1kHMwb0/видео.html
that's true and thanks for that
but the problem here was....
When you measured the output with the DMM
IT WAS NOT CLEAR ON YOUR DMM IF YOU WERE MEASURING V AC or V DC
all we could see was a cheap , no name multimeter that was showing 15.3 V
but we couldn't actually see the setting
now.. yes
common sense dictates that a bridge rectifier with a smoothing capacitor will produce DC Output
but... THIS IS A TUTORIAL and you didn't show that very clearly
your wave shape video was a lot better , in my opinion
i mean for the kiddies that don't know how it works, it's always better to have a scope to show it
and in my opinion it's much better to first show
Half Wave Rectification (so they understand how the negative half of the wave is removed)
and then to see a pulsating DC without the inverted rectified waves
and to also show them the power loss through a diode.
then ......you bring in the bridge rectifier so that the purpose is made clear
- that we get the inverted portion of the wave on the positive cycle
- that we don't lose half our power in rectification
- and that the capacitor acts as a smoothing cap to smooth out the pulsating DC
but again, you didn't make this clear
Creative Duck ,,hello,,,use this proyecto for UP to 5 amps???? Or how many Amps it is usefull??? Thanks
@@martinkuliza Tough crowd!
@@GreatWhiteNinja
Indeed
Can be use battery charger 12v?
diodes normally getting hot be careful when you put them inside the plastic box
diode is 3 amps. it will be OK because the transformer is only able to supply 800mA.
Great video
Muito obrigado, meu amigo, pelas suas informações, tão importante....!!!
Show, gained one more follower,👍🇧🇷
The components looks do big on ur hands.
Creative video, thanks :)
es exactamente lo que necesito, gracias.
F U L L B R I D G E R E C T I F I E R ! ! !
橋式整流+电容1中濾波+电感器+电容中濾波=可得更直的直流(近穩压直線),在很多開関电源後面都可以看到
مبدع
I loved that small plastoc box, from where to buy those
9v to 15v
In video
вот так вот иностранцы без всяких условий создают шедевры
Это не щедевр, а как любят делать иностранны показуха, он ничего не поднял просто конденсаторы заряжаются до амплитудного значения напряжения, а на коропбе указана номинальное, судя по конденсатору который он вставил туда при первойже нагрузке напряжение просадит и устройство будет работать не корректно
FUUUUUUULL BRIIIIIDGE RECTIIIIIIFIIIER!!!
zap
quá tuyệt vời luôn bạn ơi 😍😍 tiện bạn cho tôi hỏi đấu như nào để con điốt 4 chân thành điốt 2 chân thường vậy?? cảm ơn bạn rất nhiều 😍😍
Super działa dziękówka
Мостовой диод интересно, может диодный мост. И вообще это однофазный выпрямитель со сглаживающим конденсатором.
hize la prueba y si funciono recargue 2 baterias sin cargas solo se calento un poco el trasformador
Thanks.
Super tips
AUGUSTINE violinist from Malaysia
بسیار علی وپر محتوا
تشکر
it is really brilliant in a guide for babies
Amazing
Channel for maintenance of electrical equipment
YEEEEEEEEEEEEEEEEEEEEEEESSSSSSSSSSSSSSSSS!
What if we input dc voltage instead of ac
О БОЖЕ КАК ЭТО КРУТО... ДАЙТЕ СХЕМКУ СРОЧНО...
هل هذاا. تستر او ممكن بدل الموسيقى كلام حنى نفتهم افظل وشكرا
Video rất hay rất bổ ích cảm ơn bạn đã chia sẽ ok nhé bạn
Hello sir I have a question , I'm connecting 3x3 piezoelectric sensor and produced at around 9v how can I use tranformer and how do I connect?
Also I have another question I have connected rectifier to ac o/p of piezoelectric sensor and produced some volts but even after getting the o/p at the capacitor if I connect Dc to DC booster it is not working which is not giving o/p
I thinks that adaptor already dc
well you are wrong.The output is 9vac
AC DC เป็นวงร็อคที่โครตเทพคับ
how does that capacitor rating relates to voltage out put?
Im mostly interested to build magnet alternator so Im curriuse to know how its voltage regulator build or current cutt out if baterry reaches centrain Ah charge .
دمت گرم
Wow creative
Rectification (ac to dc) ke lie Bridge rectifier ke bajaae Center tap transformer, jis men kewal dhao diode hothaa he, behthar he.
Friend, I did something similar to turn on 12 12v bulbs, but my rectifier heats up too much. What could I use so it doesn't get too hot?
What is the best capacitor for this ?
A High or Low UF number ?
adapter is already convert ac to dc why still using gbj2510 clarification plz
No it hasn't
the Adapter output was 9V AC
the primary input was 240 V AC
it didn't convert to DC
he was basically using it so that he didn't have to manually step down the V AC
from there he basically just rectified the AC and smoothed it out with a cap.
look carefully at video 1m35sec. he already shown you.
Solder'a krenn.. Unikkk👍
How many voltage is the capacitor
Can that circuet be used with alternator?
I want some thing to build for me ignition coil useing seperate rectifier and tap in those 3 phase windings on the alternator but Im woried about me lead acid baterry if it wuld explode .
So I dont realy have negative on the coil be me its e core type ignition coil with 4 pin gm ignition module .
So can the coil and those rectifiers you show with 4 pin gm ignition module have seperate grounding?
To not interfeare with baterry ore the altrnator voltage potential?
In the past I did try out hv ceramic capacitors on me ignition coil evry thing was great except the alternator its starting charge from 1200rpm goes up to 3000rpm that was problem for me .
So please any circuets that can protect ground reference voltage and protection please.
Ciao, sul citofono ho una lampadina a 12 volt vorrei mettere una a led sempre da 12 volt il tuo circuito va bene? devo comunque sempre mettere il condensatore?Grazie
What is the diaode name please tell me
Diodes
Parabéns vídeo muito bom!
Zzzalma
Автор видео, походу китайцы тебя кинули на диодный мост и конденсатор, когда ты у них купил этот блок питания)).
Thé transformer has already done AC to DC so .
so,no it hasn't.Transformers do turn ac to dc.The bridge rectifier does,not the transformer.
The transformer don't do this alone.
how did you make a soldering iron used in this video??? please share me a link of that video.
can you make how to charge battery 12v ro 24 volts.
bisa dipakai buat ampli power gak nih
so approxiamtely you have: 9V AC *1,41= 12,69DC.if you want to have 12V DC stable output under load,from a 12vAC supply,what should you change/add?
add a IC7812 (12v positive voltage regulator), give you max 1Amp but heat sink required..
Apakah 12 volt to 15 volt ?
After Casing the electronic was looking so clean nice video
But plz explain how did we get 15 volts at output ??
It was 11v AC so when converted to DC it gains 40%, so becomes 15.4v DC
@@englishrupe01 but how did it for gain of 40 percent ?
@@parth7888 When AC gets converted to DC it gains 40%. Look it up.
Learn how FULL WAVE RECTIFICATION WORKS
Learn the steps
- do it on an Oscilloscope for yourself
- Take readings before Conversion
- Learn what Half Wave Rectification is and how it works
- Learn what a full bridge rectifier is
- Learn how it works
- make a model and test take readings
- Send and AC Signal into a Bridge Rectifier WITHOUT A CAPACITOR on the output,
Look at this through an Oscilloscope and see what you get
- then put on the cap, and see what you get
Basically the answer to your question lies in Understanding AC and DC and Wave Rectification
if we just tell you the answer, you're going to keep saying BUT WHY, ok
you need to test a few things and look up a few things and understand some fundamentals
does that help you understand it ?
buenas tardes xq te da 15 voltios si el adaptador es de 9 voltios
Los diodos de la llave reticadora retiran Los puntos de la hola eletrica. Haciendo con q haya un aumento de la energia.
You just put a bridge rectifier on a 9v DC supply. The transformer already converted to dc.
The transformer was clearly marked "9V ~". "~" means AC. Watch it again at about 2:20
Ryan Hoke it says that it is in 9 v AC. Its kinda weird but it works
Ryan transformer says 9v AC a wave sign means ac
Well if that is the case then they miss labeled the case also because a powersupply would be converting ac to dc and a transformer steps ac voltage up or down. I thought the ac symbol was the miss labeled item as ac 220 to 9v are not as common as they use to be.
This is normal AC - AC transformer in plastic box...
تحياتي لحضرتك
Merci
Eu não entendi,já n saiu corrente DC desse adaptador?
Thanks
Mas essas fontes já não vem retificadas?
Se você presta um pouco mais de atenção quando ele mostra a fonte vc vai ver que é uma rara fonte AC não sai retificado dela nao
@@valberjonesdecastro9071 O porque do fio polarizado então? (Fios da saída da fonte de 9v que se diz AC)
Kya bridge rectifier dc voltage pr work krega
Is ko hum dc to DC use kr sakte he
What cause, that 9V AC power supply can give 15V DC?
What was the point of this?
جزاك الله خير
claro el transformador es de corriente alterna a corriente alterna,un reductor,pero es alterna 9 volts...generalmente esos transforma a corriente continua x eso la confusion.....
It's a very simple rectifier system ..... I think if you put peak capacitors on the bridge rectifier it will be better.
Your solder, is it home made? Thanks
Muy bueno
Gostei muito legal
Адаптер что он использовал и так выдаёт постоянный ток, и за чем мост и конденсатор?...
What is it for? Lack of stabilization, low power
شكرا جدا للفيديو والشرح والتعليق
Thank you so much sir but how to make dc 12v 3A ? i need this adapter for my dreambox 800
Just buy a 12v 3a power supply
This is adaptor to dc
Esto puede llegar a sustituir a un MB10F?
very good video but you need one resister to protect output, otherwise the voltage would not be astable
Can u mention the resistor rating
Thank you for sharing the video, it was very useful. Greetings re-introduction
Hello, how if i want to result the output of 311vdc?
Pak bos bikinin yg pake lampu LED juga dong..serupa tp pake lampu indikator jd klu penuh biar tau.
Bạn Cho mình hỏi Điốt cầu KBU 1010 điện áp vào ~220 ; điện áp ra?
Más a fonte ja não vem retificada?
Bridge Rectifier diode number tell me plz
Le transformateur à déjà fait
Excellent
Nice fingers
Ac den dc ye olması gerekmezmiydi başlığın?
I always thought a diode bridge serves to get DC from AC like 220v etc. ....
Your Input is already DC 9v, why bother?