Hexacopter Drone using APM2.8 [Part 2] Connections and Flight controller setup | Mission Planner
HTML-код
- Опубликовано: 20 авг 2024
- Download Mission Planner : firmware.ardup...
-----------------------------------------
Required tutorials -
Hexacopter frame only Rs 200(Part 1) : • How to make Hexacopter...
Dots not appearing in Misson Planner(Compass Calibration problem) : • APM 2.8 Compass Calibr...
3 mode switch setup for flight modes : • Flysky fsi6 3-mode swi...
------------------------------------------
Drone experiments 🔻
• Top 9 Amazing Homemade...
-*-*--*-*-*-*-*-*-*-*-*-*-*
Components buy links :
1000kv BLDC Motor : amzn.to/3dOrMPt
Simon k 30A ESC : amzn.to/3pyb8Gz
1045 Propellers carbon Fiber : amzn.to/3R3FH2O
APM 2.8 Flight Controller : amzn.to/3wm3a7k
GPS Module 7M : amzn.to/3AEV9Ns
Power Distribution Board : amzn.to/3wigRUU
Flysky Fsi6 Transmitter and Receiver : amzn.to/3K9hrtM
2200 mah 3s lipo battery : amzn.to/3pxZX0L
-*-*-*-*-*-*-*-*-
Follow us on Instagram :
/ tech_at_home
Like us on Facebook :
/ tech-at-home-220885266...
#apm2.8setup#hexacopter #hexacopterapm2.8#droneusingapm2.8#techathome
Thanks for watching!
*Like Share and Subscribe
Thank You! Excellent video but one extra step is to balance all propellers with a propeller balancer and pieces of electrical tape. This makes it even more stable and less vibration to the drone. I do this for all my quadcopter builds.
Thank you for the info
can you show us how to do this correctly sir?
you saved my life bro, it helped alot
Thank you
why the arm length is 28cm only what is the reason behind it?
I have given my frame dimensions for reference, It is not mandatory.
Hello sir
Sir I had made a drone earlier hexacopter by watching your video
Drone one arm break and I had replaced it but now the problem is my drone is not arming
I reconnect all the connection and and tried again same issue
Also when I connect battery my esc instantly get super hot and smoke came from one of those although wire is normal.
I tried connecting it with arducopter but it is not showing on my laptop in port option
All the lights on arducopter are glowing
GOOD SOLID APPROACH. THANK YOU
Welcome
good demonstration with confidence, few questions, which is the best APM, transmitter, receiver you recommend fail safe design ? , instead of a motor an servo is used, how to drive with ESC, do you have any recommendations ?
Thanks for this excellent video
Welcome
Amazing 🤩
Thank you
Brother , my apm 2.8 compass celebration not work ! today i open it and see there is no mag(Compass ic) . my external compass inside gps work with arduino but not wwork with apm2.8 ! so what can i do? and can u give me a photo of your apm compass ic . i want ot replace it from a compass module.
hey bro. Im doing this DIY hexacopter drone too using PVC, and its heavy. can i only attach the apm and gps for the calibration phase? so i can turn the drone well coz if i attach everthing, its gonna be so heavy and im having a problem turning it on compass calibration. Please notice me bro
Nice video
Thank you
@@techathome plz maind ni kran apna whatsap no send Kro
how much can the drone lift and what is the flight time?
I had used old 2200 mah battery, didn't test continuously
1st view !!
How did you get the income ? Parts have become soo expensive
All components i already had , purchased 3 years back
Yes , even I was shocked with the current prices, too expensive
Btw, thank you!! for showing interest in our content
@@techathome
Hi btw
Are you interested in being a sponsor
I am a representative from an online electronic component store
Please provide your email
So we can contact you
Pleas softwear link
Software link provided in the description
Hlw sir i want to buy this hexacopter.
Sorry, not for sale
@@techathome what will be the total cost of this project ,if i want to make it for college project
When I bought the components 5 years back it was cheap. But now all components prices are high. It can go upto Rs 20,000.
Bhai Arduino ka code phone mein open kyu nhai hota
We have given zipper file for every code in our tutorial. First you need to extract and then get Arduino code ino file