I posted this on G3 Hemi Swaps on Facebook. Go there and search my name and you will see the thread along with pictures. 392 swap in 1st generation LX vehicles. I did just the engine swap in my 2006 Chrysler and been getting quite a few messages asking what did the swap entail.I have no problem sharing what I have done and have already posted what was done. 1. Need a 2009 pcm with your vin written in it and programmed with the 392 tune. 2. I used my 2006 OEM wiring harness but had to swap out the connectors for that of the 392. That's the hardest part of the swap because its tedious. 3. You need a 2012 a/c compressor and you need to use your power steering pump with 1/2 spacers for the belt to align. 4. Need a 2009 crankshaft sensor and connector. 5. You need to re-pin the wiring harness for the VVT and alternator. Not hard but again tedious. See diagram of the connectors. They will be cavities 8 and 24 but they are on different plugs. 6. You need a MSD rpm box to control the SRV on the intake manifold. That's it. Easy breezy.
I’ve done everything you’ve mentioned but mines is overheating .. new radiator, radiator fans , condenser, water pump ,thermostat and still over heating .. did pressure test on the heads and it’s all good there … what could you think the problem is with the overheating??
I think imma just build the 5.7 better anyway this is a sick build tho 🏎️ I need get right just for my first mopar 2 months ago been dreaming to have one worked hard af I’m trying get like this fr 🔨💪🏻
@Jervey Preston Ah HPT -- seems I should check out your FB thread. I am also particularly interested in the details of the engine harness. I 1000% like this method of a 392 swap as it appears to keep a full functioning OE 1st gen interior. I have an '08 5.7 BTW, and will be considering this as an option should it drop a valve seat! Thanks again for the reply.
I have a 2006 300c 5.7 and I have a 2018 charger 6.4 scat pack my scatpack is wrecked and I won’t to take motor and trans out of that and put in the 300 what else do I have to have to get started
My 07 dead on same color and body. I don’t know the real difference? But I def wanna upgrade from the 5.7 it’s still beast at 150k miles but starting to have alternator issues.
@@lameguy9862 hell nahh dont want to crank over.... 6.4 in it already 09 computer from 5.7 tuned n vined programmed to 6.4 specs idont know if its my harness at this point seen some harness diagrams for 09 an 06, they different pin lay out each one...im ready to give up on it tbh cant seem to get this mf run
If you look, I still have the third brake light on the deck. I added the trunk lid and rear taillights from an '09. Much more a cleaner sleeker look and the 08 to 10 300srt8 had the same trunk lid. The spoiler is built into the deck.
@@392goonskiii over the course of them 11 months i bought a blown up 12 Chrysler 300c used that stock engine that I took out win I put in the 6.4 … then took the 5.7 back out and 6.4 swapped my whole car motor and trans everything’s on my page subscribe bro 😎
I had a 09 chager at first but it kept having electrical issues and I couldn’t get communication to my ABS to bleed my brakes so i took my expensive parts and junked the car
facebook.com/groups/750056585062561/permalink/5529504203784418/?mibextid=Nif5oz It's in g3 hemi swaps on Facebook. On that group search my name and it's there.
im looking for a older model 300 to swap and seeing this just gave me so much hope for it and the build in general
That’s badass bro! I haven’t seen very many of these!!! Definitely will be tuned in for this build👌🏾
Who programmed your pcm to run and which connectors did you add it change
You inspire me my guy I want to do everything you did
Beautiful car, man. What about the transmission. Is ur trans 5 speed or the newer 8 speed??
I posted this on G3 Hemi Swaps on Facebook. Go there and search my name and you will see the thread along with pictures. 392 swap in 1st generation LX vehicles.
I did just the engine swap in my 2006 Chrysler and been getting quite a few messages asking what did the swap entail.I have no problem sharing what I have done and have already posted what was done.
1. Need a 2009 pcm with your vin written in it and programmed with the 392 tune.
2. I used my 2006 OEM wiring harness but had to swap out the connectors for that of the 392. That's the hardest part of the swap because its tedious.
3. You need a 2012 a/c compressor and you need to use your power steering pump with 1/2 spacers for the belt to align.
4. Need a 2009 crankshaft sensor and connector.
5. You need to re-pin the wiring harness for the VVT and alternator. Not hard but again tedious. See diagram of the connectors. They will be cavities 8 and 24 but they are on different plugs.
6. You need a MSD rpm box to control the SRV on the intake manifold. That's it. Easy breezy.
But in o6 there where no vvt on 06 5.7 so how did you wire the vvt
If you used a wiring harness from the donor car you think it would’ve been easier and you wouldn’t have to splice ?
I’ve done everything you’ve mentioned but mines is overheating .. new radiator, radiator fans , condenser, water pump ,thermostat and still over heating .. did pressure test on the heads and it’s all good there … what could you think the problem is with the overheating??
@@luisrubio262 did u bleed the system from the bleeder screw on top of water pump?
Hey bro can we chat about you swap? i really need some help @@luisrubio262
Hey man where did you go into more detail about the build
I think imma just build the 5.7 better anyway this is a sick build tho 🏎️ I need get right just for my first mopar 2 months ago been dreaming to have one worked hard af I’m trying get like this fr 🔨💪🏻
You solved my problem 🙌🏾
im stuck cant get my 05 300c 5.7 swqpped to 6.4 to crank over any way i can reach out to you?!
Looking to do this same swap what did cost look like and how much work was needed ? Any info would help
Can you make a new video on going into the details
I have 1 what was the cost for the build in all and did you have too change the transmission as well
🔥🔥🔥❤️💪300GANG🙌
Did you go full drive line , diff ,and subspension too?
I assume this still runs the NAG1. What was your method for adapting the 3.91? I ask because I did 3.06 swap and ended up swapping in TCM from 3.06
Install was straight forward. No need for a TCM when using HP TUNERS. Easily can tune the trans and change gear ratios. Yes still Nag1.
@Jervey Preston Ah HPT -- seems I should check out your FB thread. I am also particularly interested in the details of the engine harness. I 1000% like this method of a 392 swap as it appears to keep a full functioning OE 1st gen interior. I have an '08 5.7 BTW, and will be considering this as an option should it drop a valve seat! Thanks again for the reply.
@@re8672 Upgrade to the eagle 5.7 heads. All you need is the longer push rods.
Was it a 2010 rt computer ?
How much did everything else cost not including the engine
So you just use the original trans you had with the 5.7?
Did you have to change the body harness or splice any wires?
@@jerveypreston2743 the link isn’t working
I will copy it and paste it here briefly.
I posted it here in the comments.
Nice job bro
I have a 2006 300c 5.7 and I have a 2018 charger 6.4 scat pack my scatpack is wrecked and I won’t to take motor and trans out of that and put in the 300 what else do I have to have to get started
My 07 dead on same color and body. I don’t know the real difference? But I def wanna upgrade from the 5.7 it’s still beast at 150k miles but starting to have alternator issues.
5 speed or 8 speed trans?
Hey where did u get da computer swap I'm trying 2 swap my 06 as well
lmk if you are able to cranck over your car/swapped with the 6.4 in it already im stuck at this point...
@@rudy3287did you figure it out
@@lameguy9862 hell nahh dont want to crank over.... 6.4 in it already 09 computer from 5.7 tuned n vined programmed to 6.4 specs idont know if its my harness at this point seen some harness diagrams for 09 an 06, they different pin lay out each one...im ready to give up on it tbh cant seem to get this mf run
@rudy3287 you need a 09 to 12 crank sensor
@@rudy3287 you trying to sell it?
Hellow there would you share a copy from the tune file that you are running on your 300c please?
I have 09 charger v6 trinna do a scat swap I got everything frm a workin scat can I just put the wiring frm the scat like the tcm
I got a 2010 c trying do this same swap how hard is it labor and money wise
Yooo can I give you a call I’m running into that computer issue?
What did you use for the door wiring harness?
Did you finish yours?
Hey bruh where u get da computer swap I'm tryna swap my 06 also
What was the total cost my brother
Hey can you tell me who did the computer work for you?
im stuck on the same page...lmk if you got your computer work
You sure this a 06? Because the back didn’t have a brake light on the trunk till about 08-09 unless you must’ve did that?
If you look, I still have the third brake light on the deck. I added the trunk lid and rear taillights from an '09. Much more a cleaner sleeker look and the 08 to 10 300srt8 had the same trunk lid. The spoiler is built into the deck.
@@jerveypreston2743 that’s nice I always wondered if they would fit cuz I kinda always wanted to do that to mine
Thanks for the info I got a 09 and was doing the 6.4 swap bout a took the 6.4 out cuz I thought it wouldn’t run right
Bruh what😂😂😂 you took it out instead of seeing what the actual problem was
@@392goonskiii over the course of them 11 months i bought a blown up 12 Chrysler 300c used that stock engine that I took out win I put in the 6.4 … then took the 5.7 back out and 6.4 swapped my whole car motor and trans everything’s on my page subscribe bro 😎
I had a 09 chager at first but it kept having electrical issues and I couldn’t get communication to my ABS to bleed my brakes so i took my expensive parts and junked the car
What if I got a Front wheel drive
How much was the swap
What you charge
Interest in selling it?
I wanna do my 08 srt8 jeep
How much u charge
Yes officer it stock
Updates.
I’m trying to do the same I need help man
Can you link the thread I'm trying to do the same to my 07 charger
facebook.com/groups/750056585062561/permalink/5529504203784418/?mibextid=Nif5oz
It's in g3 hemi swaps on Facebook. On that group search my name and it's there.
@@jerveypreston2743link isn’t there would love a write up due to me going this swap
Did you change the interior?
No.
Around wat price did this cost to manufacture?
Anybody with the brake booster/lines
Semi bentley
Hey, I’m doing a similar swap and have a few questions. Is there anyway we could chat?
Do you have a ig or number I can text? I’m about to do this swap on a 06 v6 300
Currently doing this swap do you have social medial I can contact you on