Kia Stinger GT - Snorkel Air Scoop Install
HTML-код
- Опубликовано: 30 сен 2024
- After discovering what Horrible air intake set up the Stinger has, I've decided to buy the Air Scoop for better Ram Air Effect.
Sure the stock way, I guess works fine, with how powerful the Stinger is, but it really could have been better and I can only assume it wasn't due to lack of space for how this front end was designed, for all parts to fit and no room to direct any ram air scoops.
So, I got a pair of JA Air Scoops. You can order them Here, for the best pricing and fast shipping:
kdmwarehouse.c...
You'll need a 10mm socket, #2 Phillips screw driver (optional for few of them).. Thin flat screw driver.. ramps to raise the car up as whole, not just jack up up the one side. So you can get under it to remove push clips under the car. Don't lose any parts
Please Hit Like and Subscribe !!
Just a FYI to my friends on my channel, I've signed up as an Amsoil Dealer. If you love this product or want to know more about protecting your car, motorcycle, Boat, Truck, etc.. with the best oils and tranny, gear lubes, cleaners, etc. Check out the products here oh my Direct link for Amsoil Products: @t
how to make vehicles run on alkali solution, ammonia solution, alcohol solution: electrolysis (can be fuelcell dry/wet hho, radio frequency hho, or plasma hho generators) inside fuel filter (injection vehicles) or big custom float bowl (carburetor vehicles) , and inside combustion chamber by plasma from multi sparkplugs, water laser ignition sparkplugs, we need hack the electrycity by change regular stator/altenator with high current one, then adding air scoop with wind turbine electric generator (all land, sea and aviation vehicles can use it as external electic current generator) inside it and put alternator on propeller shaft or axle (for cars, truck and other wheelers vehicles) and electric motor stator generator inside center of rear velg and front velg (for cars, motorcycles) this guaranteed free energy by movement of vehicles and wind that come from front of vehicles, then use supercapacitor in hydrogen generator connection cable and varistor in coil-ignition sparkplugs cable, then make electrolysis inside fuel filter first electrolysis (pem or plasma hho or by radio freq hydrogen generator), because grafity effect, water inside fuel filter or float bowl will make pressure so hydrogen don't come back to fuel tank come down but up right into injector or carburetor fuels spray, by injecting or spraying both hydrogen and water into internal combustion chamber chain reaction (explosion by next electrolysis stage must been happening inside combustion chamber) plasma sparkplugs or water laser ignition sparkplugs will make electrolysis+ignition , the principle is same like lightning strike on sea (natural electric plasma electrolysis) that convert sea water into hydrogen and oxygen + make pressure at sea water then burn it cause by lightning strike hit hydrogen (explosion of water on sea by lighting strike) on it this mean all vehicles actualy can run and burn on water and hydrogen, the scheme will same to fuelcell electric vehicles which when inside i.c.e engine we burn hydrogen and water in fcev we just injecting hydrogen from electrolysis right into fuelcell
I recently installed the Velossa bigmouth intakes on my stinger as well. The bumper cover removes very easily and no issues. What I don’t understand is why everybody removes the large air scoop for the radiators. You do not have to remove that, I just simply placed my big mouth in position and took a razor knife and made small trim cuts on the large scoop and you have a custom fit and you still have an affective air scoop
from what I can tell, these scoops don't cover a lot of area in front of the Rad, so it really should not affect it at all. Tons of real estate of direct air to hit the Rad. More odd why the engineers put these air scoops facing up ?
@@rpmautoreviews9249 maybe not but why rewire all those cables and zip tie them to your bumper when you don’t even have to pull it out
@@harrymason5032 if I cut out the area of that part I took out, then yes, I don't have to remove it.. and in my video, for those who watch the whole thing (i know most do not), I showed that you could just cut that part out and not have to remove it.. Maybe I should have done it that way. but it doesn't seem to really do anything really. All the air hits the car as you drive.
So if you cut the shroud and install the snorkel(s) through it, do you even need to remove the shroud to make the cuts? I am leaning toward this route as well, especially if you don't even need to remove it and put it back in!
Any issue with rain/road water getting funneled direct into the air filters?
I think I’m going to wait until I install my intercooler video to do this one! Thanks for all the work and step by step!! 💪💪 Stinger fam 🐝
That certainly makes sense. As I was watching the video I said to myself, if he is doing that much work, he should do the intercooler now also. :-)
@@pcthayer I don't want an intercooler. I know itll help, but it's not $200 and I am not going to win a Free Cruise around the world if I get better 1/4 mile times due to cooler turbos... so ... I am not totally have to update my car, kind of guy.. car runs fine.. :-) if everyone wants to start a go fund me to pay for all the cool mods, I'm o.k to put them all on.. haha
Hello and thanks for the video. Will snorkel air ram lite kit fit the gt line. I know gt line is single but the set up is the same.
It should help with one. They work great on mine
@@rpmautoreviews9249 cool. Thanks
I’m going to order the kit.
Kia is really weird for not giving the Stinger GT the stock ram air system it easily could of had.
I can't fathom why they'd go so far out of their way to obstruct those intake ports In front of the airbox. Other than to prevent hydrolock or something, but I doubt that would've been a common occurrence.
probably because itll be too beasty ! haha.. most likely no room without ruining another part of engine bay area & parts, etc.. ????
@@rpmautoreviews9249 I gotta admit, I'm really curious to see what you get out of the snorkels.
I think a lot of people negate their effectiveness by going with simple short rams in the engine bay. But then they leave themselves susceptible drawing in the heat of the turbos. (Though some try to hide their intakes away in a box.)
But the stock system is fully enclosed from the engine heat in plastic, and now the only strong access to air is exclusively coming from outside, which will always be cooler than inside the engine bay.
I have a good feeling about your next dyno.
@@rpmautoreviews9249 have you gotten any 0 to 60 times or quarter mile time since replacing the air intakes? Curious to see if it took any time off of your best or average runs.
Looks good. What if there is heavy rain ? Isnt water washing air filters ?
I am told no by others. Other cars have more direct intake vents as well.
Great video thanks!
It's the same for the g70 3.3t. I'm about to do new snorkels intercooler and air intakes
The thumbnail is a different car, which is odd.
I used one from the website where I bought them. Didn't have a photo that I liked.
@@rpmautoreviews9249 got it. Great install by the way - appreciate the detail 👍
Hey sir just wanted to say thank you for the step by step. I wish I could send a photo.
Stavros because you had to remove the bumper to install the air scoops you should have changed the intercooler also. 2 birds with one stone....
haha.. you just want me to spend all my Santorini $$ & pimp out my stinger.. haha.. I havent heard of it overheating, so dont believe its an issue... if it was, how would i know ? engine & oil temp gauges have yet to really go up.
Has anyone who installed them had a problem with moister from rain or snow? Just bought a 2022 and the Velossa but want to be sure b4 i install them.
I havent yet & likely will never have. few curves in flow, so will be hard for rain to make it thru that.
If you really want a 20-40 horsepower gain, you need a better intercooler. It doesn't "make your turbos cooler" it cools the charged air that heats from going through the compressor and gives you a denser amount of air going into the motor. You will see huge gains from a bigger more efficient intercooler.
Would this require to then have better exhaust to handle the extra HP ? and a tune to handle and properly adjust timing, fuel mixture ? I personally dont want to do anything that'll force me to do more for it to work properly. This set up has got me .3 secs better 1/4 mile times and all is good so far.
@@rpmautoreviews9249 No you do not need to do anything to the exhaust. A tune is not necessary but if you want to make the most out of all the mods you currently have it will be the single biggest boost in power you can do. With a Turbo charged car you can get 80-100 hp just by getting a good tune, because the manufacture leaves so much on the table when it comes to turning up boost.
Wouldn't it suck driving in the rain with those snorkels? Worst thing is to direct rain into your intake.
rain doesnt make it in there. there is like 5 curves before entering the intake. Never get wet !
@@rpmautoreviews9249 Hmmm.
O.k. So video to follow with some runs from this evenings test n tune. It was a bit cooler out than the last time I was here, but bit closer to the temp my first time out few weeks ago at this same place "Shannonvile Motorsport Park"... and first two times there, I averaged 13.5 and 13.6 (average of all runs that were o.k. launch or better).. my best was 13.159 I think... Well, today with the air scoops in, I average 13.2 (taking guess, as I haven't actually done the math yet).. and my best two runs were 13.068 @103.33mph and 13.069 @ 103.32mph.. and have a couple at 13.1's and 13.3's. one bad one at 13.5's... so about 10 runs and consistently better.. I suspect the cooler temp helped, but it wasn't cold. Just not as hot as Sunday . I really suspect the scoops helped out.. and my best 60 foot was 2.003 (before Up I was averaging 2.09)... Not even $300 to my door, $$ well spent. Runing on Shell V-max 91... most runs were in SM and some in Custom Mode, w/sport settings except for awd in Comfort, for a better launch, because the start pads not the stickiest here). Videos to follow next week.. Still have a few more to load from Sunday's runs. Look out for them brothers
Holy moly your stinger is slow. My 2022 with just k&n intakes and vellosatech snorkels runs 12.5 @ 113 mph on the street with bad traction. Im taking it to a track soon so it should run 12.3s at least with better traction.
Your DA could vary quite a bit from his. I don’t know this but this is my guess why you see that difference.
I'm surprised by all the rust (3m36s, 5m08s for example) on the core support. What year is this car?
19. i did rust proofing when i got it, but i guess they dont spray everywhere properly
@@rpmautoreviews9249 looks like its on/around the welds used for their clips. Could probably get away with hand sanding and getting a few layers of primer/paint on there if u eventually have it off again for intercooler upgrades etc.
I think 🤔 you could of saved your money 💰 by leaving them off for more cooler air 😎 😉 😎 I'm a supercharged fan 😉 not much of a turbo fan because you lose boost power over so many runs I'm just saying people's upgrade intercooler would be the best guess for your turbo or Supercharged and turbochaged etc..
how would i get more cooler air by not installing these ? or what did you mean ?