This video saved me a headache. thank you! Additional information: 1. To remove the bottom seat, just pull straight up because it has two snap-in tabs. 2. To remove the back rest, just lift straight up but it is little difficult and use T50 torx to remove the 2 screws. 3. Use the long stick with a hook to pull the latch. 4. To remove the whole back rest, once the trunk opened, there are two holes that you can use the screw driver to twist the latch.3 so that you can easily put the back rest back in step 2.
Thank you sooooo much for posting this video. We were locked out of our BMW with the battery completely disconnected and were ready to try the method where you trip the trunk wire. You saved us a huge hassel! Especially as we didn't know what we were doing, really. I hope this helps someone else in this situation where you cannot get into the trunk and jumping the battery isn't an option. Our BMW is a 2010 328i, and it worked all the same. I ended up using a broom handle that I was able to slide into the trunk with 2 others holding up the back car seat. I sure hope BMW has corrected this design flaw!
THANK YOU! Your video helped me. All I had to do was open the center section of my rear seat and reach through all the way back with a long screw driver to pull the release handle down. You have to use a flashlight so you can see the pull handle and put the screwdriver in the D ring to push it down. I would have never found the release cable without your video. The release is too far back to grab with your hand so use any tool, or a wooden stick, to pull the D ring down. This will open your trunk! Thanks again bro!
Thank you for your video. Like you, I removed the battery and closed the trunk to secure the car. Once I did that I could not get access to the trunk again. There’s no key hole on the trunk, and I tried putting jumper cables on the front battery posts. BUT... since there is no battery connected, the circuit is not complete. So all those people who just say “just hook up a small battery or jumper cables...”, IT DOES NOT WORK WITHOUT A BATTERY. So thank you for your video. I freaked out for two days, then I followed your steps and it worked for me. I’d say the only issue I had was the two star screws. At first pass, it looked like the T40 bits were the right size, then I stripped several T40 bits until realized it was a T45 but. But overall got it to finally work after watching your video.
Thank you for this video!!!, I'm sorta glad i'm not alone in doing this, fyi in response to 2 other comments I used a t45 torx, and there is NOT a manual key hole for trunk entry on this car
Glad it helped! And this is becoming easier to do it because people have been explaining things better on their comments. Thank you all for helping people save money. Also check the other video where I add a rope to open the truck. I have there all the time just in case that happens to me again.
Ryan Kraus, no problem. I’m glad it worked for you. I broke the Negative cable clamp and it would die all the time. So adding the rope was easy way to pop the trunk open.
The backseat won't lift all the way off because of the headrests which have to be released....u guessed it...via the trunk. But it does raise enough to get a coat hanger on that release handle.
The fact that you have to go to such lengths to get to the battery is a major oversight by BMW. There are some really nice things about BMW’s but man there are some really stupid things to. Why on earth they would not have an easy fail safe for this situation is pathetic on their part.
So in the front in the passage area inside the car , you remove that part and there are cables that open the trunk. Why this information was not online ???? That is what the expert from BMW did and the trunk opened even when there was no battery and the trunk was locked in this 328i 2010 bmw. I wish someone would have mention this method .
NES ADDICT Yes, there’s like 4 if I’m not mistaken. They’re in the bottom and they need to be removed. So you can lift the seat enough for someone to go through the bottom into the trunk and pull on the release lever.
no need to take out your backseat. all you needed to do was to use your key which is attached to your fob. underneath the trunk there is a key slot. stick it in and turn real hard.
Hey I’m just getting into Car DIY’s but I’m having a bit of some trouble getting the backseat screws off. My ratchet doesn’t seem to fit. What is the best tool to get those off? (I am completely confused with the tools and names)
Ratchet with an extension, you have to put pressure on the seat cushions. Stick something in between to separate the recliner and seat. That should help. Slide your hand through the seat and feel the screws. I don’t recall the tools but I need to watch the Vedic to remember
@@kickbuttozki9761 yea the 2 star bolts that are holding the back seat together is extremely HARD to do. I was trying to troubleshoot my battery when I finally got it disconnected and closed the trunk not realizing it would lock me out xD. I found an easier fix and you don’t need to unscrew or play around with anything. Simply get into the car and pop the hood open. Connect cables to the positive and negative terminal in the hood (each of them have it in the front + battery in the trunk) and allow someone to connect the other end to their car. Your car will then have electric power and you can then just press the trunk button on the key fob or inside. It’s faster and easier
I made the same exact mistake and I’m going crazy right now....I have a 2010 535i and I think my backseat has a black firewall to stop me from getting in the trunk I’m not sure but I’ll check....if u can help me....anybody plzzz reply this is my reality for 5 days now thank you in advance
You could only lift or pull from the bottom.. and reach in with a stick or something. Have someone hold the recliner for you.. My daughter was skinny enough to slide in and pull on the emergency release pull
Fyi: there are positive and negative jump connector points in the engine bay where any size. 12 volt battery even a motorcycle battery will work enough that your key fob should work to open the door switches and trunk release switch. Perhaps easier to jump the car than undo all the back seats..
VW1971C10, You’re are you absolutely right. That is if the battery is low and in the car. This happened when I took the battery out. And when to purchase it. After that, I had to call a tow. They tried jumping it from the front just like you mentioned but without the battery. It was almost impossible for the car to charge or make the fob key work.. Thanks you for your opinion. I’m sure if someone reads this conversation they would do a better job than me and learn not to close the trunk once they remove the battery.
This video saved me a headache. thank you!
Additional information:
1. To remove the bottom seat, just pull straight up because it has two snap-in tabs.
2. To remove the back rest, just lift straight up but it is little difficult and use T50 torx to remove the 2 screws.
3. Use the long stick with a hook to pull the latch.
4. To remove the whole back rest, once the trunk opened, there are two holes that you can use the screw driver to twist the latch.3 so that you can easily put the back rest back in step 2.
Thank you sooooo much for posting this video. We were locked out of our BMW with the battery completely disconnected and were ready to try the method where you trip the trunk wire. You saved us a huge hassel! Especially as we didn't know what we were doing, really. I hope this helps someone else in this situation where you cannot get into the trunk and jumping the battery isn't an option. Our BMW is a 2010 328i, and it worked all the same. I ended up using a broom handle that I was able to slide into the trunk with 2 others holding up the back car seat. I sure hope BMW has corrected this design flaw!
What size tool did you use oleae
Godz Kidz It was a torque bit but I don’t know what size we used. We had several different sizes to choose from.
Hmmm our 2010 is probably built differently because this didn’t work the same . When we unbolted we faced another barricade behind the seat 🤨
Thanks! My dad locked the battery in the trunk and he was scratching his head trying to figure it out. You made me look like a hero!
Gracias bruh needed this one out of all of them this is my problem right now
This video is a life saver. Bmw is being designed by idiots since opening a trunk is so difficult.
THANK YOU! Your video helped me. All I had to do was open the center section of my rear seat and reach through all the way back with a long screw driver to pull the release handle down. You have to use a flashlight so you can see the pull handle and put the screwdriver in the D ring to push it down. I would have never found the release cable without your video. The release is too far back to grab with your hand so use any tool, or a wooden stick, to pull the D ring down. This will open your trunk! Thanks again bro!
Thank you for your video. Like you, I removed the battery and closed the trunk to secure the car. Once I did that I could not get access to the trunk again. There’s no key hole on the trunk, and I tried putting jumper cables on the front battery posts. BUT... since there is no battery connected, the circuit is not complete. So all those people who just say “just hook up a small battery or jumper cables...”, IT DOES NOT WORK WITHOUT A BATTERY.
So thank you for your video. I freaked out for two days, then I followed your steps and it worked for me. I’d say the only issue I had was the two star screws. At first pass, it looked like the T40 bits were the right size, then I stripped several T40 bits until realized it was a T45 but. But overall got it to finally work after watching your video.
From all the vidz on RUclips,this video sorted me out💪🏽👍🏽😂
Thank you for this video!!!, I'm sorta glad i'm not alone in doing this, fyi in response to 2 other comments I used a t45 torx, and there is NOT a manual key hole for trunk entry on this car
Great, Thank for clarifying more information. I have other videos that I can make.
I want to say thank you for sharing this as well! So huge!
Thanks a million... every other video didn't apply to my specific problem.
Man!! I owe you a coke or a Pepsi or ice cold beer, Thank You.
You are welcome. If I can help let me know.
Thanks bro this helped me out a lot
We tried this approach and really works Thanks
Yeah, this was easier just by watching your tutorial! Many thanks man!
Thank u i was about making a hole on the dam car
Glad that I helped you.
Just works on mine thanks for the video
Glad it still helping people out there!
This helped me so much thank you man
Glad it helped! And this is becoming easier to do it because people have been explaining things better on their comments. Thank you all for helping people save money. Also check the other video where I add a rope to open the truck. I have there all the time just in case that happens to me again.
Mate your a life saver!!!
I just did the same thing! Thank you for this video! 🙏🏼
thanks to you and my sister i made it!
Ahahah thnx a lot!
Thanks for tip , bro!
Ryan Kraus, no problem. I’m glad it worked for you. I broke the Negative cable clamp and it would die all the time. So adding the rope was easy way to pop the trunk open.
Thanks for the video. Very helpful 👌
The backseat won't lift all the way off because of the headrests which have to be released....u guessed it...via the trunk. But it does raise enough to get a coat hanger on that release handle.
That’s correct
You’re welcome. I’m glad that it helpful.
The fact that you have to go to such lengths to get to the battery is a major oversight by BMW. There are some really nice things about BMW’s but man there are some really stupid things to. Why on earth they would not have an easy fail safe for this situation is pathetic on their part.
Thank very much it work for me
Where would you find the screws on a coupe back seat? All I see are the seatbelt screws
You can just put cables on the terminal under the hood and just pop it with the button… 😂
What about a blown fuse nothing wrong with my battery but my trunk won't open which fuse is it?? Before I go changing every single one
So in the front in the passage area inside the car , you remove that part and there are cables that open the trunk. Why this information was not online ???? That is what the expert from BMW did and the trunk opened even when there was no battery and the trunk was locked in this 328i 2010 bmw. I wish someone would have mention this method .
Thank you, BUT, you don't have to remove the seat belts👍🏼👌🏽
Thanks but does it work on 2009 bmw
At least you have an idea
All you had to do was get jumper cables attach it to where the battery jumps in the engine bay and just just open the trunk with key fob
I tried, I removed the battery to buy one and locked the trunk
Exactly!! That’s what I said 😂
Is there a handle to drag in every BMW? I have a 2010 330d touring, and I don’t find, can not see, find the handle to drag.
Yes they all should have it.
Does anyone know exactly what size bit I need to remove the back seats?
Hi. What's your model e90 or f30 ???
2011 BMW 328i falls on the e90
We’re there any screws removed to pull the bottom of the back seat up?
NES ADDICT Yes, there’s like 4 if I’m not mistaken. They’re in the bottom and they need to be removed. So you can lift the seat enough for someone to go through the bottom into the trunk and pull on the release lever.
NES ADDICT You won’t be able to fully remove the seat, only pull the bottom up. And squeeze someone in there.
no need to take out your backseat. all you needed to do was to use your key which is attached to your fob. underneath the trunk there is a key slot. stick it in and turn real hard.
😂😂😂
2011 I know so not have key slot under the trunk maybe older e90s
Those 2 tork 50 screws won’t come out, I’ve tried using a ratchet set and a drill and no matter how much force I use, they won’t come out.
Hey I’m just getting into Car DIY’s but I’m having a bit of some trouble getting the backseat screws off. My ratchet doesn’t seem to fit. What is the best tool to get those off? (I am completely confused with the tools and names)
Ratchet with an extension, you have to put pressure on the seat cushions. Stick something in between to separate the recliner and seat. That should help. Slide your hand through the seat and feel the screws. I don’t recall the tools but I need to watch the Vedic to remember
@@kickbuttozki9761 yea the 2 star bolts that are holding the back seat together is extremely HARD to do. I was trying to troubleshoot my battery when I finally got it disconnected and closed the trunk not realizing it would lock me out xD. I found an easier fix and you don’t need to unscrew or play around with anything. Simply get into the car and pop the hood open. Connect cables to the positive and negative terminal in the hood (each of them have it in the front + battery in the trunk) and allow someone to connect the other end to their car. Your car will then have electric power and you can then just press the trunk button on the key fob or inside. It’s faster and easier
I made the same exact mistake and I’m going crazy right now....I have a 2010 535i and I think my backseat has a black firewall to stop me from getting in the trunk I’m not sure but I’ll check....if u can help me....anybody plzzz reply this is my reality for 5 days now thank you in advance
I removed all the torque bolts but it’s still not coming off man
You could only lift or pull from the bottom.. and reach in with a stick or something. Have someone hold the recliner for you.. My daughter was skinny enough to slide in and pull on the emergency release pull
Lift from one corner in the bottom
I need to know what I can use to take it off
If your talking about the star screw? You need a size T45 bit.
👍👍👍👍👍👍👍👍👍👍👍👍👋🙏🙏🙏🙏🙏🙏🙏
Fyi: there are positive and negative jump connector points in the engine bay where any size. 12 volt battery even a motorcycle battery will work enough that your key fob should work to open the door switches and trunk release switch. Perhaps easier to jump the car than undo all the back seats..
VW1971C10, You’re are you absolutely right. That is if the battery is low and in the car. This happened when I took the battery out. And when to purchase it. After that, I had to call a tow. They tried jumping it from the front just like you mentioned but without the battery. It was almost impossible for the car to charge or make the fob key work.. Thanks you for your opinion. I’m sure if someone reads this conversation they would do a better job than me and learn not to close the trunk once they remove the battery.
What tool again ?
9T or 10T, if you just buy a set of star bits you would be good. I suggest to get the ones that you’re able to use a ratchet.
Got it done, thanks
Such a stupid problem to have!