DIY AM/FM Radio Kit: Crafting Radio Receiver

Assembling and testing an electronic DIY kit "AM/FM radio CF210SP".
This video shows how to make an AM/FM radio at home using an electronic DIY kit. The circuit use IC CD9088 and TDA2822 and does not need to be adjusted after assembly.
This kit is very suitable for users to learn electronic circuits, practice and proficient soldering skills, enhance electronic professional knowledge and interest.
Check out another FM radio DIY kits:
• How to make FM radio r...
• Building a DIY FM Radi...
• Building an FM radio |...
• FM Radio Kit: Crafting...
Playlist with other electronic kit projects - • Electronic kit projects
#icstation
#fm_radio
#diy_radio
#am_radio
#diy_fm_radio
#diycrafts

[@adielveras]

Excelente vídeo - muito bem filmado! Ajudou-me muito a montar o rádio 📻 kit. ❤

[@DIY_Simple_Circuits]

Estou feliz por ter gostado.

[@stefangetsov7836]

Well done job. Bravo!!!

[@stefangetsov7836]

❤❤❤ i only cant understood,where you connect the ferit antenna.....?

[@stefangetsov7836]

What a radio...one single transistor within😂😂😂

[@DIY_Simple_Circuits]

At 5:34 you can see where the coil is connected.

[@ominkan3129]

Your case fits like a glove. Mine not even close on the tuning capacitor side.

[@DIY_Simple_Circuits]

These sets vary in quality, from not bad to very poor.

[@Bartok_J]

Probably the most disappointing of all the Chinese kits I've built, but, then, one of the cheapest.
It's actually quite a reasonable circuit: performance quite good for a simple design. But let down by poor components, a poor quality pcb that is difficult to solder to, with thin copper tracks that come off with the heat of the soldering iron, and an ill-fitting case with a crude tuning mechanism that doesn't work properly. :-(

[@Colonel_Flanders]

I'm trying to build mine right now. The resistors it came with are poorly labeled and they have a lot of variance when I try to test their resistance.

[@dz-abouttechnique1849]

Nice video!

[@DIY_Simple_Circuits]

Thanks!

[@reinaldogoncalves8047]

Este vídeo é o melhor que encontrei. Já estou em fase final de montagem, seguindo suas instruções. Acho que soldei o led um pouco mais rente a placa, não sei se terei que tirar e soldar novamente. Você fixou o alto falante com cola? Qual a temperatura e a velocidade do ar do soprador que vc usou para a solda em pasta? Valeu demais, obrigado!!! Já me inscrevi no canal e dei um joinha.

[@DIY_Simple_Circuits]

Que bom que você gostou. Sim, o orador foi fixado com cola. A temperatura do ar é 350, a velocidade do ar é mínima.

[@reinaldogoncalves8047]

Terminei a montagem. Olhando o seu, parece encaixar tudo direitinho, mas o meu não encaixa ao fechar. As vezes liga o AM, outras não, principalmente quando fecho. FM nem pensar. Acredito que soldei tudo correto. Vendo algumas avaliações de onde comprei, tem muitas críticas, inclusive de rachaduras nas trilhas. ​@@DIY_Simple_Circuits

[@DIY_Simple_Circuits]

@@reinaldogoncalves8047 A qualidade desses conjuntos não é muito boa.

[@ominkan3129]

Thanks for the video. Did you have to adjust the tuning capacitor for receiving the full bands?

[@DIY_Simple_Circuits]

Yes, the tuning capacitor was adjusted by the regulators on the other side.

[@ominkan3129]

@@DIY_Simple_Circuits Thank you very much. If you have time can you say which screws adjustment is for AM and then the other two must be FM. There are four screws.

[@DIY_Simple_Circuits]

As I remember, after soldering, only two screws are available for adjustment. The one at top is for AM.

[@ominkan3129]

@@DIY_Simple_Circuits Oh on mine there are 4 adjustable screws. I guess I will do some tweaking to see what I can get. Right now one FM station out of 10 available and no AM out of 4 available. Thanks again for all your videos.

[@lancebaruela8882]

what is the paste that you put??

[@DIY_Simple_Circuits]

This is solder paste Mechanic XGZ40.

[@FrankDens]

Have also put it together only noise no music what did I do wrong ?

[@DIY_Simple_Circuits]

Check the correct soldering, correct placement of details, antenna connection.

[@stefanpascutoiu]

L-am cumparat si eu dar nu am stiut sa lipesc firisoarele cele mici

[@bashavideos94]

I want purchase

[@DIY_Simple_Circuits]

www.icstation.com/radio-210sp-radio-soldering-assembly-kits-p-15937.html
or
www.aliexpress.com/w/wholesale-cf210sp-radio-kit.html

[@muhammadrafique3903]

Very good information videos thanks sir ❤❤Rafique mastoi DG Khan Pakistan 🏝🇵🇰

[@DIY_Simple_Circuits]

Glad you like it.

[@manikwaghmare9262]

😮😮

[@muralidp5158]

Iwhere do i get this kit to purchse

[@DIY_Simple_Circuits]

AliExpress www.aliexpress.com/w/wholesale-cf210sp-radio-kit.html

[@RKteaching501]

Sir एक रेडियो असेम्बिल करके मेरे पास भेज दीजिए।

[@nandsagartiwari2423]

कितने में मिल सकता है

[@DIY_Simple_Circuits]

इस आइटम के लिए विभिन्न मूल्य हो सकते हैं।
www.aliexpress.com/w/wholesale-cf210sp-radio-kit.html

[@ashishraut8048]

Kaha se liya

[@DIY_Simple_Circuits]

AliExpress www.aliexpress.com/w/wholesale-cf210sp-radio-kit.html

[@AlexeyPankov-zh1kf]

🖐👍👍👍👍👍👍👍👍👍👍✊

[@999apex]

我有製作完成一個，品質不如預期，不好控制選台，made in china

[@DIY_Simple_Circuits]

您可以嘗試調整可變電容器上的調節器。它可以提供幫助。

[@chalmh]

Sensitivity, selectivity and sounds like junk.

[@DIY_Simple_Circuits]

Agree.

[@Jessica_Flores2]

Seym kit

[@rjsanjoyofficial]

I have no money to buy it. Please give it to me for free.

[@DIY_Simple_Circuits]

But I'm not selling anything. I only bought this one and assembled it.

[@rjsanjoyofficial]

Give me one please....🙏

[@vivetu]

No merece la pena ni el tiempo ni el estaño de soldadura invertido en este kit. Es pura basura

[@DIY_Simple_Circuits]

Absolutamente, tienes razón. Este kit no es de muy buena calidad.

[@dilipdhote640]

I want purchase

[@DIY_Simple_Circuits]

AliExpress www.aliexpress.com/w/wholesale-cf210sp-radio-kit.html