@@aarongottfried5595 It can work on wet surfaces. But best is for the area to be dry and clean. I haven't used steelstik. It is the same brand as the waterweld and says it works on plastic as well so may work.
I came looking for an easy solution for a shower drain leak. Not only did I find that, I found a fascinating aquaponics channel. Thanks for the quick video, saved me a lot of time!
I used this to patch a pvc pipe running along the house. Five years later, the stuff is still working fine. JB Weld products are life savers...no I do not work for them..haha.
Thanks for this comment! I have a T on a line that is split and will try this. Not an easy fix as the 3 lines for the front yard are lined up together!
dude...I have never used this stuff before but just attempted to use on the underside of my kitchen sink for a large crack. I did about half the length of the crack and wasted so much because I was having to mound it on and smudge or else it would just stick to me and pull off the sink. I saw your tip and instantly tried it, and was able to easily kneed the putty, then roll it and form near perfectly along the rest of the crack. Thank you.
Dude wish I could subscribe to and like this video a hundred times, You have saved me from getting a new boiler!! I used all kinds of silicone crap and none worked and then i found this!! A big thank you to you my friend!!
Had a crack under my house at a fitting, it would of been damn near impossible to replace just because of reaching it and it being right where it goes through the floor.. Knew there had to be something like this to patch it so water wouldnt leak, i was gonna use silicone but glad i stumbled across this. Thanks a ton!
@@thebigguy963 This stuff, along with most any epoxy products cure very hard, so most likely this epoxy “patch” job that he did will last until he has yet ANOTHER brain fart and drills an additional hole in his drain pipe… that clearly shouldn’t be there!!! However, this is just my opinion and I do not know anything about the person who posted this comment, nor am I familiar with any of the stuff that he is -working- -on- destroying!!! 🤣🤣🤣
I was looking for something like this. I've got an upstairs bathroom drain that's leaking in a pvc joint. I can just barely get to it through my downstairs ceiling. The joint is in hole in the ceiling joist and it would be a mess to cut another hole and cut out a bunch of pvc. I'm going to try to wrap this around the joint and see how well it holds. I've used other JB products before and they're really good. Thanks for showing.
@@prakashuppu448 It works It works very well. Adheres to pvc and stays solid. Make sure the pvc is really clean or maybe sand it off and clean it before you apply.
I noted an epoxy repair on the copper water pipe in my basement when I moved in to my new house. I've been trying to make time to solder a new pipe. Five years later I have yet to make a code approved repair. Since it's still holding fine and it's in the unfinished part of my basement I will leave it alone for now. Thanks
After you've gotten the gunk and epoxy on your hands... Rub your hands in the dirt... the more, the better. The dirt will take to the epoxy, then wash your hands. It's not a perfect way, but better than not trying. This works for want sticky stuff on your hands.
I’ve got a beauty machin and it’s got a tiny leak and I was told it would cost me £595 to fix the leak, and I can’t afford it so I will try this first and hopefully it will save me lot of money
Thanks bro. My tube didn't come with ANY directions. Your vid was quick and concise. Exactly what I needed since I'm trying to do this repair rn. Thank you!
Thank you so much for your tip and demonstration! I went to the store and bought the epoxy paste and fix something that I was about to trash it but I did not Wanted cause I paid $159 and it cost me just $8 to fix it my self. Thanks again.
Was the water on or off when you patched it? My neighbor won't shut her main off for fear of admitting liability,which a certified plumber told me it IS her line!
Thanks. I have a slow leak on a drain pipe from a tub - there is access from the basement. I wanted to find a way to fix the leak without replacing the drain & pipe/s because it's in a tight awkward location. I'll get the product & try it.
A few weeks ago our plastic tub dishwasher started leaking. Learned that after years of use, the bleach (in your dishwasher soap) and heat (from the heating element) has a deteriorating effect on the plastic. I found one hole (1/8" x 3/16") under the element. I purchased the JB Weld epoxy, which will hold up to the water and heat. I prepped the hole area and another spot starting to show signs of deterioration. I applied the epoxy inside the tub, and after removing the kick panel, to the underside area. It's been almost two months with no leaks. Also as my water is hot enough and I don't need the element to dry, I turned the element off.
Tried it on small pvc pipe leak on a hot tub. Didn't work at all and this was a pretty small leak. I have a hard time imagining this product being useful in many applications.
I was about to say the same thing.Ive done it wrong before and it didn’t work and I’ve prepped it correct and it worked like a miracle.Like most thinks if you wrong it won’t work.Definitely works good and its also very strong.
I need to fix some bathroom sink water supply lines, would this work?? I think it’d definitely be worth a try! It’ll save me some money considering I would have to replace them all… it’s just leaking a tiny bit because it’s a plastic fitting screwed onto a metal faucet.
Thanks for the info! I had a plumbing repair done last week and at least one of the joints is leaking (about 1 drop every 30 seconds). Hopefully this will do the trick.
It should work on that. Just clean it up so that it has the best chance to adhere to the pvc. A down side is that pvc pipe has high thermal expansion so eventually overtime it could leak again. Basically due to temperature changes pvc could expand or shrink causing the JB weld to become loose.
@@vonponics water in his case is under pressure. I'm dealing with a pinhole on black plastic but it's right at the joint fitting of the 20 lb. pressure filter on a commercial hot tub. most JB products I've seen should take a little pressure. ?
@@Dwightstjohn-fo8ki ya it should hold up against pressure. It does also come down to how well it adheres to the surface, and whether or not you were able to get a good seal.
For anyone needing an epoxy for pressure PVC pipe like for repairing a hot tub freeze situation, there's only one product that is guaranteed to work. Weld-on 10813 (also known as Weld-on 810). Hard to find, but go to a plumbing supply (some pool supply stores will carry it too). Just note this is some incredible stuff that requires caution. It's a 2-part epoxy that is easiest applying by hand. BUT, wear at least three pairs of nitrile gloves when working with it, it will eat through the gloves. You have about 4 min to work with it once mixed and it will be rock hard in 10 min and cured within an hour. Also wear a mask when applying, the fumes are fairly overwhelming. Incredible stuff that melds into the PVC. No other stuff that I've found like it. Amazon used to carry it but no longer sells it.
Just tried this tonight on my kitchen sink drain, leaking at a joint. Hard access area behind drywall so I tried to put it all around the best I could. Fingers crossed!
I'm in the same situation, hard to reach drain pvc line with a leaking elbow but I think I can manage to put this stuff all around. Did it work for you?
Thanks for this. I appreciate the clairty in your exlplanation. Is it difficult to remove once its on? I am looking to do a temp fix where the faucet meets the pvc. But I would like to eventually replace the faucet.
I will try this on my toilet bowl drain pipe, after silicone, flex tape didn't work, maybe this will do the trick It's barely no pressure there but somehow it's still dripping
can you use this to seal a crack on a pvc pipe that is leaking water under ground (backyard, 1 ft under ground/lawn, cracked while using a shovel without knowing there was a pipe)..
Great video. Can you or anyone else comment on the pressure ratings? What is the water pressure of your system? I have a leak and the pressure behind it is about 15 psi. Perhaps an ‘adjustable screw clamp’ around the finished product before it settles could be helpful?
Sorry but I couldn't tell you my psi I don't have a way to test it. Plus I did do some renovations to the aquaponic system, so those spots with the epoxy in the video are no more. The packaging does say 1300psi but idk how accurate that is, you probably have to attach it to the pipe just right for that to happen.
This is probably 3 months late already, but here it is anyway: I just tried to patch a crack on the pvc water pipe going into my house, which at least 120psi, and it only held it for about 10 seconds before it started leaking again. In my case the crack is at the base of the thread that is exposed where the PVC meets the copper. It is a tricky spot with a lot of contour and near the ground/dirt. Also I suspect waiting 1 hour to cure is not enough. I re-did it and made sure the putty coverage extends both PVC and copper side. I'll wait 2-3 hours this time and try again. But so far my conclusion is: This putty might be good to patch even pipe surface, but not joints. Also, I don't think it will work for the water pipe going into the house. Not where I live at least. good luck!
When I used it it hardened. You need to mix both parts together well. And it is still holding up and still hard to this day. It may leak eventually again, but so far so good.
@@vonponics Hi. You just needed in your fingers? That jb "water" weld product stays soft when i do that. It's almost like play dough and never hardens.
@@dennisrobinson8008 yes I needed it with my fingers. Then after it is all needed together I apply it to the area. After applying it to the area it becomes hard. I forget how long after I had to wait for it to harden, but it hardened.
you need to mix well That means fold it over twist it roll it for abt 1/2 minute or 40 times at least .It's gotta be warm to the touch before applying. and smear it into the gaps hard with pressure to get good adhesion. Make a thin smear to make sure you get it to stick to the surface then add more. Then let it cure at least 4hrs or overnight before H2O pressure. Most people get in a hurry glob it on a dirty wet surface an fk it up.
Did not help with the leak in pvc at elbow joint. Started leaking again after a week. Apparently this stuff stays soft when there is a water on it and eventually will start leaking again 😢
What did you end up using on the pond? We’ve got one with a hole that was supposed to be the drain but leaked and now that we have a pump, we just want to ceil the hole up. What would you do?
If I can get a little more info that would be great since I don't quit follow. But here is a guess: What do you mean by what did I use on the pond. Are you referring to the part when I talked about using JB weld on my pond filter. If so it worked for some time, but I ended up just switching the part out since that area had a lot of movement and made it hard for the JB weld to stay sealed. And for your pond what hole are you referring to. thanks
Does this work on the actual pipe or just where it connects like where you were doing? I got a pretty decent leak in the pipe and taking everything apart looks terrible hard
It should work anywhere on the pipe. But I have found that when using it you have to get it on just right for it to work. So it can be a hit or miss at times, but if attached well it can last for some time. If one spot isn't attached to the pvc pipe to well, it will still leak. Smooth it out as best you can and take your time when applying it.
Ive been using this and i just cannot get the leaks to stop finding a way through the putty. Im just going to keep applying more and more till it stops
I haven't personally used it on a sprinkler system. However I am going to assume it should work, as long as you can get it to adhere to the pvc. Sometimes getting it to stick can be tough. Best would be to sand the pvc area and clean it the best you can. The product says it has a strength of 9000 psi so theoretically it should have no problem with the pressure of the sprinkler system. But again attaching it to the pvc can sometimes be tricky.
I am going to assume you are referring to the spot at 4:00 min. Were earlier in the video you saw that I only put it on half the pipe. I didn't put enough of the epoxy from the start so water just seeped out from higher up on the pipe. It is hard to get a good seal when you just put it half way around the pipe like I originally did. It leaked because of the factor that even if I got a good seal at the bottom area water will just come out of another area around the fitting since the piping wasn't glued. The leak might not have even been coming from the bottom but from higher up and just dripping down (I don't remember), so putting the epoxy just at the bottom was kinda useless. So I therefore added more epoxy around the whole area where the fitting was, to seal it off. Hope that makes sense. Note: It basically came down to me wanting to save money by using less epoxy and only putting it at the bottom area of the piping, but that didn't work out so I just added more.
It might work for a little bit. But since that is a flexible pipe the seal will break. For that the easiest is just to get a barbed adapter like this: amzn.to/3hbLYZE Very easy to do and alot more effective.
I am not entirely sure since I haven't used it on abs plastic. But I do believe that it should work. The only thing with both pvc pipe and abs is that they have high thermal expansion so eventually overtime it could leak again. Basically due to temperature changes pvc and abs could expand or shrink causing the JB weld to become loose.
JB Water Weld product safety notice on Amazon UK states "TOXIC TO AQUATIC LIFE with long-lasting effects" (even though other info suggests it's ok to use with drinking water), so I suggest careful research if intending to use this on ponds.
I've got a clamp on the upstairs neighbors' line(leaking into my condo,hoa is useless)and I bought some plumbers epoxy putty,should I try that if/when the clamp fails? Somebody please? The upstairs neighbor is just as uncooperative as the hoa! smfh.
not entirely sure since I haven't put it on silicon. I remove the silicone that I had before. But I do think you can just surround the silicone with the epoxy, as long as the epoxy is attached to the pipe that doesn't have the silicone it should be good.
Anyone can tell if it sticks to rusted metal pipes, and holds the pressure of 10 households, with half of them two floors above the leak? It would be Very useful for the next 36 hours.
I have a small leak in my back yard sprinkling system's PVC pipe. I put this on and a little while later it still leaked. Then I tried drying the area and also wrapped over it with Super Glue "E-Z Fuse Tape". Now, it still leaks! WASTE OF MONEY! Next time I am going to have copper pipes put in. I HATE PLASTIC stuff! These pipe are getting daily sun and should have been either painted, or better yet . . . copper.
Link to the JB weld on amazon:
amzn.to/3iKrRC6
hi is this for wet surfaces? does steelstik work the same?
@@aarongottfried5595 It can work on wet surfaces. But best is for the area to be dry and clean. I haven't used steelstik. It is the same brand as the waterweld and says it works on plastic as well so may work.
@@vonponics it doesnt work just did it
@@aarongottfried5595 Thanks for letting us know
Does plumber's putty work for this kind of leak?
If it is pressurized pipes, my guess is not.
I came looking for an easy solution for a shower drain leak. Not only did I find that, I found a fascinating aquaponics channel. Thanks for the quick video, saved me a lot of time!
Hey, I’m here looking to fix a hole in a drain pan… did you ever fix it?
I used this to patch a pvc pipe running along the house. Five years later, the stuff is still working fine. JB Weld products are life savers...no I do not work for them..haha.
Thanks for this comment! I have a T on a line that is split and will try this. Not an easy fix as the 3 lines for the front yard are lined up together!
dude...I have never used this stuff before but just attempted to use on the underside of my kitchen sink for a large crack. I did about half the length of the crack and wasted so much because I was having to mound it on and smudge or else it would just stick to me and pull off the sink. I saw your tip and instantly tried it, and was able to easily kneed the putty, then roll it and form near perfectly along the rest of the crack. Thank you.
2:00 Take what you need, and knead what you take.
I just saved $450 by watching this video. Thanks!!!!!!
Dude wish I could subscribe to and like this video a hundred times, You have saved me from getting a new boiler!!
I used all kinds of silicone crap and none worked and then i found this!!
A big thank you to you my friend!!
Product is easy to install and kept the pool warmer than it had usually been. Extended the use of the pool by a month or so. Great value!
Thanks!
Had a crack under my house at a fitting, it would of been damn near impossible to replace just because of reaching it and it being right where it goes through the floor.. Knew there had to be something like this to patch it so water wouldnt leak, i was gonna use silicone but glad i stumbled across this. Thanks a ton!
I was just about to purchase some Flex Paste, but this looks like a way better option, thanks for the video
Flex tape is a complete waste of time and worst... money!
@@doxx2427 I will second this. Never will purchase it again.
I used it on a hole I accidentally drilled in a drain pipe. Works great, thanks!
how long does it last?
@@thebigguy963
This stuff, along with most any epoxy products cure very hard, so most likely this epoxy “patch” job that he did will last until he has yet ANOTHER brain fart and drills an additional hole in his drain pipe… that clearly shouldn’t be there!!! However, this is just my opinion and I do not know anything about the person who posted this comment, nor am I familiar with any of the stuff that he is -working- -on- destroying!!! 🤣🤣🤣
I was looking for something like this. I've got an upstairs bathroom drain that's leaking in a pvc joint. I can just barely get to it through my downstairs ceiling. The joint is in hole in the ceiling joist and it would be a mess to cut another hole and cut out a bunch of pvc. I'm going to try to wrap this around the joint and see how well it holds. I've used other JB products before and they're really good. Thanks for showing.
Does it work? Mine having same problem
@@prakashuppu448 It works It works very well. Adheres to pvc and stays solid. Make sure the pvc is really clean or maybe sand it off and clean it before you apply.
I noted an epoxy repair on the copper water pipe in my basement when I moved in to my new house. I've been trying to make time to solder a new pipe. Five years later I have yet to make a code approved repair. Since it's still holding fine and it's in the unfinished part of my basement I will leave it alone for now. Thanks
Thanks for this video. I’m glad you shared an affiliate link. Idk how much you get but I hope it helps in some way
Thank you for the video going to use it for a connection on the side of my house. Take care!
After you've gotten the gunk and epoxy on your hands... Rub your hands in the dirt... the more, the better. The dirt will take to the epoxy, then wash your hands. It's not a perfect way, but better than not trying.
This works for want sticky stuff on your hands.
or... just wear... gloves?
Thanks, that's exactly where my leak is in my garden irrigation system.
no problem
Did it work? About to try this instead of digging it all up
@@Dan007UTdid it work for you?
@@exia1989yes it did
I’ve got a beauty machin and it’s got a tiny leak and I was told it would cost me £595 to fix the leak, and I can’t afford it so I will try this first and hopefully it will save me lot of money
Thanks bro. My tube didn't come with ANY directions. Your vid was quick and concise. Exactly what I needed since I'm trying to do this repair rn. Thank you!
Thank you so much for your tip and demonstration! I went to the store and bought the epoxy paste and fix something that I was about to trash it but I did not
Wanted cause I paid $159 and it cost me just $8 to fix it my self. Thanks again.
Glad I could help!
Was the water on or off when you patched it? My neighbor won't shut her main off for fear of admitting liability,which a certified plumber told me it IS her line!
Thanks. I have a slow leak on a drain pipe from a tub - there is access from the basement. I wanted to find a way to fix the leak without replacing the drain & pipe/s because it's in a tight awkward location. I'll get the product & try it.
A few weeks ago our plastic tub dishwasher started leaking. Learned that after years of use, the bleach (in your dishwasher soap) and heat (from the heating element) has a deteriorating effect on the plastic. I found one hole (1/8" x 3/16") under the element. I purchased the JB Weld epoxy, which will hold up to the water and heat. I prepped the hole area and another spot starting to show signs of deterioration. I applied the epoxy inside the tub, and after removing the kick panel, to the underside area. It's been almost two months with no leaks. Also as my water is hot enough and I don't need the element to dry, I turned the element off.
Im using on a PVC valve on my pool! Thanks !
Tried it on small pvc pipe leak on a hot tub. Didn't work at all and this was a pretty small leak. I have a hard time imagining this product being useful in many applications.
U didn't clean it well enough an u should of sanded it
I was about to say the same thing.Ive done it wrong before and it didn’t work and I’ve prepped it correct and it worked like a miracle.Like most thinks if you wrong it won’t work.Definitely works good and its also very strong.
I need to fix some bathroom sink water supply lines, would this work?? I think it’d definitely be worth a try! It’ll save me some money considering I would have to replace them all… it’s just leaking a tiny bit because it’s a plastic fitting screwed onto a metal faucet.
How long does it need to cure before turning the water back on?
Your video just saved me a lot of time and MONEY!! Thank you.. Subscribing to your channel now..
You’re a life saver. Thank you
Thanks for the info! I had a plumbing repair done last week and at least one of the joints is leaking (about 1 drop every 30 seconds). Hopefully this will do the trick.
What’s the verdict? I’m thinking of fixing basically the exact same situation as yours
Need that for fixing Hoover Dam its leaking bad and Las Vegas going run out of water soon for electric power
Can you use this on copper?
Thanks for your support
My dear friend
Is it available in karachi pakistan?
Good video, good narriation brother!!
Thank you so much, I wanted to buy flex seal but I saw your video.
Glad I could help
thanks for the suggestions
Nicely done! Thank you...
nicely demonstrated
would this work on the pvc pipe that provides cold water to my water heater?
It should work on that. Just clean it up so that it has the best chance to adhere to the pvc. A down side is that pvc pipe has high thermal expansion so eventually overtime it could leak again. Basically due to temperature changes pvc could expand or shrink causing the JB weld to become loose.
@@vonponics water in his case is under pressure. I'm dealing with a pinhole on black plastic but it's right at the joint fitting of the 20 lb. pressure filter on a commercial hot tub. most JB products I've seen should take a little pressure. ?
@@Dwightstjohn-fo8ki ya it should hold up against pressure. It does also come down to how well it adheres to the surface, and whether or not you were able to get a good seal.
For anyone needing an epoxy for pressure PVC pipe like for repairing a hot tub freeze situation, there's only one product that is guaranteed to work. Weld-on 10813 (also known as Weld-on 810). Hard to find, but go to a plumbing supply (some pool supply stores will carry it too). Just note this is some incredible stuff that requires caution. It's a 2-part epoxy that is easiest applying by hand. BUT, wear at least three pairs of nitrile gloves when working with it, it will eat through the gloves. You have about 4 min to work with it once mixed and it will be rock hard in 10 min and cured within an hour. Also wear a mask when applying, the fumes are fairly overwhelming. Incredible stuff that melds into the PVC. No other stuff that I've found like it. Amazon used to carry it but no longer sells it.
Just tried this tonight on my kitchen sink drain, leaking at a joint. Hard access area behind drywall so I tried to put it all around the best I could. Fingers crossed!
Did it work?
Did it work?
I'm in the same situation, hard to reach drain pvc line with a leaking elbow but I think I can manage to put this stuff all around. Did it work for you?
Thanks for this. I appreciate the clairty in your exlplanation. Is it difficult to remove once its on? I am looking to do a temp fix where the faucet meets the pvc. But I would like to eventually replace the faucet.
No problem. Glad I could help. I have used a chisel and a hammer to take it off which worked.
Great stuff! Thanks for sharing.
Imagine hiring a plumber and he spends an hour under the sink only to find out that’s all he used. 😁
Can i use on my pool fitting?
yes
This works on wet GI pipe
Hi will the water still Leak while the epoxy is curing?
It depends on how much pressure there is. If there is a lot of water just gushing out best is to turn the water off and wait for it to cure.
I will try this on my toilet bowl drain pipe, after silicone, flex tape didn't work, maybe this will do the trick
It's barely no pressure there but somehow it's still dripping
The 2-ounce container is very small and may be insufficient for certain situations.
can you use this to seal a crack on a pvc pipe that is leaking water under ground (backyard, 1 ft under ground/lawn, cracked while using a shovel without knowing there was a pipe)..
Yes you can but for something like that I would just purchase some couplers and fix it properly.
I just used it for a cast drain pipe in my kitchen, had to let it set for 1 day, but no more leaks.
Great video. Can you or anyone else comment on the pressure ratings? What is the water pressure of your system? I have a leak and the pressure behind it is about 15 psi. Perhaps an ‘adjustable screw clamp’ around the finished product before it settles could be helpful?
Sorry but I couldn't tell you my psi I don't have a way to test it. Plus I did do some renovations to the aquaponic system, so those spots with the epoxy in the video are no more. The packaging does say 1300psi but idk how accurate that is, you probably have to attach it to the pipe just right for that to happen.
This is probably 3 months late already, but here it is anyway: I just tried to patch a crack on the pvc water pipe going into my house, which at least 120psi, and it only held it for about 10 seconds before it started leaking again. In my case the crack is at the base of the thread that is exposed where the PVC meets the copper. It is a tricky spot with a lot of contour and near the ground/dirt. Also I suspect waiting 1 hour to cure is not enough. I re-did it and made sure the putty coverage extends both PVC and copper side. I'll wait 2-3 hours this time and try again.
But so far my conclusion is: This putty might be good to patch even pipe surface, but not joints. Also, I don't think it will work for the water pipe going into the house. Not where I live at least. good luck!
@@DodySuratman this helps. Our pvc pipe just ruptured at the valve where you would turn the water on/off to the house so this poxy wouldn't work
Is this any good for pvc spa pipes?
I have not used it personally on spa pipes, but it should work on those pipes as well.
@@vonponics 👍
does it work on painted metal pipe?
I would sand the paint off. Better to attach it to the raw material of the pipe.
With the thread leaks you could put teflon on it
Thanks . Very helpful
Does it matter if there is literally a tiny pinhole like drip? Or can I slap it right on there
you should be able to just slap it on there.
Appreciate the video❤
I need to fix leak in a rubber fitting connecting abs and cast iron; would this work?
It might work. Doesn't hurt to try.
Can u use this on an outside pipe that will constantly get wet?
yes I have used it in spots that were under water.
The are was dry when I applied the epoxy but then it got filled with water.
Can u remove it after long time?
Ya I was able to remove it with a chisel.
Excuse me can i use that product on copper pipe???
I haven't used it on copper but on the products packaging it says it works on copper.
Does it work under pressure?
Yes it should. But I find if it is not applied just right it will leak.
great video Thanks !
Does the jb weld water weld harden? I recently used s
recently used some it doesn't appear to harden.
When I used it it hardened. You need to mix both parts together well. And it is still holding up and still hard to this day. It may leak eventually again, but so far so good.
@@vonponics Hi. You just needed in your fingers? That jb "water" weld product stays soft when i do that. It's almost like play dough and never hardens.
@@dennisrobinson8008 yes I needed it with my fingers. Then after it is all needed together I apply it to the area. After applying it to the area it becomes hard. I forget how long after I had to wait for it to harden, but it hardened.
you need to mix well That means fold it over twist it roll it for abt 1/2 minute or 40 times at least .It's gotta be warm to the touch before applying. and smear it into the gaps hard with pressure to get good adhesion. Make a thin smear to make sure you get it to stick to the surface then add more. Then let it cure at least 4hrs or overnight before H2O pressure. Most people get in a hurry glob it on a dirty wet surface an fk it up.
Would this water weld work on metal pipes??
I haven't personally used it on a metal pipe. But the product says it should work on metal.
You have some nice equipment there. Tilapia in the tanks?
Thanks
I do have some blue tilapia, red Nile tilapia, and Mozambique tilapia.
how much psi can it take ?
he said on the product is 9000psi
Did not help with the leak in pvc at elbow joint. Started leaking again after a week. Apparently this stuff stays soft when there is a water on it and eventually will start leaking again 😢
What did you end up using on the pond? We’ve got one with a hole that was supposed to be the drain but leaked and now that we have a pump, we just want to ceil the hole up. What would you do?
If I can get a little more info that would be great since I don't quit follow.
But here is a guess:
What do you mean by what did I use on the pond. Are you referring to the part when I talked about using JB weld on my pond filter. If so it worked for some time, but I ended up just switching the part out since that area had a lot of movement and made it hard for the JB weld to stay sealed.
And for your pond what hole are you referring to.
thanks
Im about to jb the top of my windshield where water is leaking in my Truck when it rains...any suggestions
let us know how it goes.
I would rather use liquid RTV its thin watery silicone made for windshild leaks at the rubber seals.
Does this work on the actual pipe or just where it connects like where you were doing? I got a pretty decent leak in the pipe and taking everything apart looks terrible hard
It should work anywhere on the pipe. But I have found that when using it you have to get it on just right for it to work. So it can be a hit or miss at times, but if attached well it can last for some time. If one spot isn't attached to the pvc pipe to well, it will still leak. Smooth it out as best you can and take your time when applying it.
Ive been using this and i just cannot get the leaks to stop finding a way through the putty. Im just going to keep applying more and more till it stops
prolly should have sanded the area first. If you have a Dremel you may have to grind off the the original repair and start over.
@@barneycarparts I did sand the area pretty good. Idk like I said I'll just keep trying.
Does this work with sprinkler pvc with the pressure
I haven't personally used it on a sprinkler system. However I am going to assume it should work, as long as you can get it to adhere to the pvc. Sometimes getting it to stick can be tough. Best would be to sand the pvc area and clean it the best you can. The product says it has a strength of 9000 psi so theoretically it should have no problem with the pressure of the sprinkler system. But again attaching it to the pvc can sometimes be tricky.
Did you try it? Did it work?
I used it on a road shower and it wouldn't even hold 20 psi
Great video. Thanks.
why did you go back and add JB Water Weld to the leak you fixed? did it start leaking?
I am going to assume you are referring to the spot at 4:00 min. Were earlier in the video you saw that I only put it on half the pipe. I didn't put enough of the epoxy from the start so water just seeped out from higher up on the pipe. It is hard to get a good seal when you just put it half way around the pipe like I originally did. It leaked because of the factor that even if I got a good seal at the bottom area water will just come out of another area around the fitting since the piping wasn't glued. The leak might not have even been coming from the bottom but from higher up and just dripping down (I don't remember), so putting the epoxy just at the bottom was kinda useless. So I therefore added more epoxy around the whole area where the fitting was, to seal it off. Hope that makes sense.
Note:
It basically came down to me wanting to save money by using less epoxy and only putting it at the bottom area of the piping, but that didn't work out so I just added more.
Needed this video! English bulldog puppy chewed on our pool drain 🤦🏻♀️❤️🐶
Glad it was helpful!
I accidently cut a slice of my aquapex. Would this work on it?
It might work for a little bit. But since that is a flexible pipe the seal will break.
For that the easiest is just to get a barbed adapter like this: amzn.to/3hbLYZE
Very easy to do and alot more effective.
Will it work on abs plastic pipe?
I am not entirely sure since I haven't used it on abs plastic. But I do believe that it should work. The only thing with both pvc pipe and abs is that they have high thermal expansion so eventually overtime it could leak again. Basically due to temperature changes pvc and abs could expand or shrink causing the JB weld to become loose.
Is it pond fish safe?
Yes
JB Water Weld product safety notice on Amazon UK states "TOXIC TO AQUATIC LIFE with long-lasting effects" (even though other info suggests it's ok to use with drinking water), so I suggest careful research if intending to use this on ponds.
I've got a clamp on the upstairs neighbors' line(leaking into my condo,hoa is useless)and I bought some plumbers epoxy putty,should I try that if/when the clamp fails? Somebody please? The upstairs neighbor is just as uncooperative as the hoa! smfh.
I can't be used on pressured water lines. Great video, though
Did it harden?
yes
You saved me bro thanks
Wer can i buy that
amzn.to/3iKrRC6
How to remove this from pipe again, it’s very hard now
I have done it with a chisel and hammer
Thanks - really helpful!
Is it better than resi bond please reply
I am not sure since I have not used that product.
does it stick to silicon??
not entirely sure since I haven't put it on silicon. I remove the silicone that I had before. But I do think you can just surround the silicone with the epoxy, as long as the epoxy is attached to the pipe that doesn't have the silicone it should be good.
Anyone can tell if it sticks to rusted metal pipes, and holds the pressure of 10 households, with half of them two floors above the leak?
It would be Very useful for the next 36 hours.
Thank you
It would not stick for me
I have a small leak in my back yard sprinkling system's PVC pipe. I put this on and a little while later it still leaked. Then I tried drying the area and also wrapped over it with Super Glue "E-Z Fuse Tape". Now, it still leaks! WASTE OF MONEY! Next time I am going to have copper pipes put in. I HATE PLASTIC stuff! These pipe are getting daily sun and should have been either painted, or better yet . . . copper.
for cracks its best to drill a 1/8 hole just beyond the end of the crack. It keeps the crack from continuing to run.
I need this, ASAP
I couldn't get a seal because the water leaking was creating voids
Don't make a habit of not wearing gloves. Your liver will thank you.
Does not worrk on PVC to Brass fittings. I wish it did so sad.....
Thank you for your awesome video…..on my way to pick some of this stuff up!
Splash zone ftw
Thanks for tips man!
No problem!