Do moter ko VFd lagane ke bad 1 no motor chalu hone ke bad hi dusri motor chalu honi chahiye. Ager 1 no motor band he to 2 no motor chalu nahi honi chahiye interlock karna he please bataye
GPD 315/V7.... Ka on off kon sy number terminal sy ho ga.. Galti sy S+ S_.. R+ R_ ko galti sy 24 volt dy dia tha.. Ab koi hal hai.. Please give me reply
Meri motor start karne per jab band karta hun to turant per ho jate thoda rang mein band hona chahie uske liye kaun sa setting hai mere ko jaane han Jaan jankari chahie
Sir. I have a question, why I don't have output frequency and 0 current in the f7 driver, I change and check everything and the motor still not run, only the stop light is blinking
Mujhe Ek help chaiye mera application aisa hai Ki drive par preset Timing deni hai 5 second me Fwd direction fir next 5 sec rev direction , Aur ek Application hai Har 2 second me speed 10-20;30 hz jana chaiye 50 par stop
been attempting to set S6 and S7 to be inhibit switches for travel limits of direction. I have tried 7 and 9 in H01.07 and H01.06 and also tried B and D in H01.06 and H01.07, it takes flashes UL2 Upper limit, and LL2 for lower limit, i am thinking my interface terminal board might be bad. Anyone got any recommendation ?
Sir. Bahut. Khub. Samjhate. Hai. App. Dhanybad
Bhut badhia
Presentation is very usefull
Very nice teaching
PLEASE EXPLAIN TORQUE CONTROL CONFIGURATION
very good..thanks for your time
Very nice video sir
Thanks
सिमन्स drive ka bhi video banaye sir
Push button mai Red vala nc use hoga ya no
Thank you sir your explanation
Yaskawa V1000 मे
S1,S2 मे Forwrd Revers मे 8 rpm और दुसरा स्पीड S5 मे 800 rpm चाहीये क्या करना होगा.
How to do 800 rpm
Thank you so much sir
Thank you sir.good messeg
Good
Thanks
Shir g j1000 me bhi parameter dal sakte hai kya
Sir external fault use kaise krte hai no NC mein ek video bnaye
Pls make same video also on Danfoss drives...
Full pramitter ka video banaiye
Do moter ko VFd lagane ke bad 1 no motor chalu hone ke bad hi dusri motor chalu honi chahiye. Ager 1 no motor band he to 2 no motor chalu nahi honi chahiye interlock karna he please bataye
Dear sir
Kindly make a video digital terminal selection
Bhai yaskwa ke sare modal me kw setting liye o2-o4 me 1hp se 300hp tak kya hex value aayegi as par video banao
Sir Lift rev frd 4flor ka limit switch ke satth video bnaye
Schnider vfd ke upar video banaiye sir
Ok
सर मुझे Yaskawa V1000 मे forward और Reverse मे 8HZ पर चलना है और तिसरी स्पीड जो है वो फुल्ल स्पीड forward 50HZ पर चलाना है क्या करना होगा..
Sir yaskawa ko servo motor pr kasy auto tune krty ha video bnyae
GPD 315/V7.... Ka on off kon sy number terminal sy ho ga..
Galti sy S+ S_.. R+ R_ ko galti sy 24 volt dy dia tha..
Ab koi hal hai.. Please give me reply
Sir connection to samajh gae lekin parameter Nahi samjhe please sir ek video
Nice explanation.
Please upload a vedio for tourque control method with parameter settings
Yes sir ditails parameters
Sir yaskawa varispeed7 ka connection aur terminal function ka kuchh batye
Meri motor start karne per jab band karta hun to turant per ho jate thoda rang mein band hona chahie uske liye kaun sa setting hai mere ko jaane han Jaan jankari chahie
Sir yaskawa v100 drive motor forward to reverse direction changing parameters bolosir
Pura details batai sir parameter seting
👍
Salam sir... Sir fualty drive ko multimeter say k say check kartay hai is pe koi video banay...
Thnks sir
Sir. I have a question, why I don't have output frequency and 0 current in the f7 driver, I change and check everything and the motor still not run, only the stop light is blinking
Isme potential free relay ka use karke drive ko stop karna ho to kese kare???
Mujhe Ek help chaiye mera application aisa hai Ki drive par preset Timing deni hai 5 second me Fwd direction fir next 5 sec rev direction , Aur ek Application hai Har 2 second me speed 10-20;30 hz jana chaiye 50 par stop
Yaskawa drive 15 kw se 12.6kw ki motor chalane k liye kaise set kre
Witaj,
prosze o link do tej instrukcji
Paramitar ko fansan ke duru ad kare
Sir v1000 inverter when I changing frequency busy message coming, what's the problems
Ad ke bina nahi dikhata sakte he link tut jata he
Potentiometer ka velu kitna hoga?? 10k or 100k
2wire kya hai /3wire kya hai
"Jota he, re he he, muta he, vala he" What language is this?
A1000 parameter setting eot crane list
been attempting to set S6 and S7 to be inhibit switches for travel limits of direction. I have tried 7 and 9 in H01.07 and H01.06 and also tried B and D in H01.06 and H01.07, it takes flashes UL2 Upper limit, and LL2 for lower limit, i am thinking my interface terminal board might be bad. Anyone got any recommendation ?
Thanks sir, my one question how to configure s6&s7 digital input and its parameters?
I wish it was english
Good vedio ❤ I need Drive parameter for PID controller for pressure control . Also pl share your mobile no for asking any doubts
Não entendi nada
Detail me parameter seting bataie sir
Inovance vfd error 16 ka matalab