This is some of the best info on router bits specific to luthiers. Especially for beginners and those buying their first router, it can be overwhelming with all the different bits and all the different dimensions. I hope your videos get the attention they deserve.
Thanks. As someone who likes learning new skills and techniques, I am trying to see where others may need that little note or angle that may seem obvious to seasoned pros.
When I 1st started making guitar blanks and necks, I had some scary situations with the straight cut Pattern Bits. I use either a Spiral or compression bit, with the Compression bit (fairly expensive) works like a charm. The Infinity Mega Flush Trim router bit, or the Whiteside Ultimate Trim Combination Router Bit are my suggestions for starters. The Whiteside runs about $195 and the Infinity Mega runs about $89.
These sound like great bits and I am sure would give great results and are easier to work with IF you can afford them. Sadly a lot of beginners will not want to spend $195 or even $89. I have learned to work with $10-15 bits and get decent results, and I think that is what many first-time / amature luthiers usually deal with. I am sure you appreciate the 'fancier' bits even more after using the straight ones. 😉
Do you need a plunge router to do cavities (i.e. pickups, tremelo, etc.), or can you also do it with a trimmer router? Also, when I am doing it in sections, is the area (depth) covered reliant only on the length of the bit blade, or are the bits secured into the router the same way a drill/driver bit is into a drill, where you can put it deeper in, or have it sticking further out? Thanks, and, GREAT video. Second to none. :)
I have a small trimmer router, and a large (non plunging) one. Aside from the planging action making work eaisier on the entry, it's a matter of power. The small trimmers may just not be able to handle deeper cuts with harder woods. If this is your only option, you can get by with multiple passes and slow motion. Do make sure you have a sharp bit.
@@theelectricluthier1928 Thanks. Could I get by with a cheap bit, or is that something that you really need to go ahead and spend a little more money on? I just don't want to pay for expensive bits if it's not really necessary (as I'm on a _tight_ budget, and there are so many different tools needed to do a whole project).
@@51MontyPython I would love to get those 200$ bits to really know what they're like, but I am not there yet either. I think my most expensive bit (the large round over bit, I do the neck with) was around 15$. The cheap ones work, just work slowly, consider the routing direction and check that your bearings are in good shape. Be safe and enjoy them.
I love this tutorial, very informative 🙂 but may I suggest that you use a clip on mic If you can for better audio quality and for more relax tone of voice though I can here you clearly. I already subscribe to your channel, thank you for sharing 🙂
Thanks for the comment and the suggestion Ninja, I believe I have improved the quality and the tone since this video was done. (What do you think of more recent ones?) As with guitar building, there is always a place for learning and improving. There is also the dilemma: should I get another tool, or upgrade the recording equipment?...
![Megan Thee Stallion - Neva Play (feat. RM) [Official Video]](http://i.ytimg.com/vi/TpYTyAaTRts/mqdefault.jpg)
This is some of the best info on router bits specific to luthiers. Especially for beginners and those buying their first router, it can be overwhelming with all the different bits and all the different dimensions. I hope your videos get the attention they deserve.
Thanks. As someone who likes learning new skills and techniques, I am trying to see where others may need that little note or angle that may seem obvious to seasoned pros.
This video helps me a lot with my project. And show me that iam on the right way.
Thanks a lot. Luthiers
Thank you for that, and you are most welcome.
When I 1st started making guitar blanks and necks, I had some scary situations with the straight cut Pattern Bits. I use either a Spiral or compression bit, with the Compression bit (fairly expensive) works like a charm. The Infinity Mega Flush Trim router bit, or the Whiteside Ultimate Trim Combination Router Bit are my suggestions for starters. The Whiteside runs about $195 and the Infinity Mega runs about $89.
These sound like great bits and I am sure would give great results and are easier to work with IF you can afford them. Sadly a lot of beginners will not want to spend $195 or even $89. I have learned to work with $10-15 bits and get decent results, and I think that is what many first-time / amature luthiers usually deal with. I am sure you appreciate the 'fancier' bits even more after using the straight ones. 😉
Thanks. That's been a helpful set of examples.
🙏 Thanks, glad I can help
Do you need a plunge router to do cavities (i.e. pickups, tremelo, etc.), or can you also do it with a trimmer router? Also, when I am doing it in sections, is the area (depth) covered reliant only on the length of the bit blade, or are the bits secured into the router the same way a drill/driver bit is into a drill, where you can put it deeper in, or have it sticking further out? Thanks, and, GREAT video. Second to none. :)
I have a small trimmer router, and a large (non plunging) one. Aside from the planging action making work eaisier on the entry, it's a matter of power. The small trimmers may just not be able to handle deeper cuts with harder woods. If this is your only option, you can get by with multiple passes and slow motion. Do make sure you have a sharp bit.
@@theelectricluthier1928 Thanks. Could I get by with a cheap bit, or is that something that you really need to go ahead and spend a little more money on? I just don't want to pay for expensive bits if it's not really necessary (as I'm on a _tight_ budget, and there are so many different tools needed to do a whole project).
@@51MontyPython I would love to get those 200$ bits to really know what they're like, but I am not there yet either. I think my most expensive bit (the large round over bit, I do the neck with) was around 15$. The cheap ones work, just work slowly, consider the routing direction and check that your bearings are in good shape. Be safe and enjoy them.
I love this tutorial, very informative 🙂
but may I suggest that you use a clip on mic If you can for better audio quality and for more relax tone of voice though I can here you clearly.
I already subscribe to your channel, thank you for sharing 🙂
Thanks for the comment and the suggestion Ninja, I believe I have improved the quality and the tone since this video was done. (What do you think of more recent ones?) As with guitar building, there is always a place for learning and improving. There is also the dilemma: should I get another tool, or upgrade the recording equipment?...
@@yoavbinyamini I did check it,
It sounded much better 🙂 another great video thanks 👍
Super
Thanks 🙏
For trimming the sides of the body should I use a bit that is the exact length or is it better to use one that is slightly longer?