P2784 P0717 P2767 Diagnosis Input speed sensor No Signal Dodge Charger Magnum Challenger Chrysler300
HTML-код
- Опубликовано: 22 авг 2024
- Originally I got the code p2784 INPUT SPEED SENSOR 1/2 CORRELATION.
Then it progressed to P2767 INPUT SPEED SENSOR 2 CIRCUIT NO SIGNAL.
This is also related to P0717 INPUT SPEED SENSOR 1 CIRCUIT NO SIGNAL and is a similar repair.
NAG1 5 Speed transmission. How to fix this issue.
The scanner showed i was losing n3 sensor input speed. After replacing the transmission conductor plate. The issue is now resolved.
Thanks for watching! Please feel free to like, comment, and subscribe!
Good video man one question do you know by any chance if the rear wheel bearings on a 06 charger rt tone rings if they all rusty do you know if thatll cause the car speedometer to not move at all or not go over 20 mph? I can only go up to 2nd gear but by only using the manual shifter tia bro
Thanks for the comment bro, appreciate it. The vehicle uses the wheel speed from all of the wheels in order to calculate the vehicle speed for the speedometer. So, sometimes you can lose the vehicle speed, especially if you don’t have readings from both rear wheels. The transmission uses the rear wheel speed sensors in order to calculate the transmission output shaft speed. So if they don’t have a signal then the transmission will not be able to detect output speed, and it will not be able to shift. If your tone rings are bad. They can be replaced, by removing the old one, and pressing a new tone ring on the old axle. Some other people just replace the rear cv axles and it will come with a new tone ring as part of the new axle assembly. Good luck with your vehicle bro!! 🤝💯
@@colin7761 thank you brother how can I tell if my tone rings are bad or cv axle or my conductor plate can a bad conductor plate cause my car to not run?
If you’re able to, scan your car for all the codes, and let me know what it says. The specific codes you have will help point us in the right direction and then we can go from there. If you have no scanner turn the key on and off 3 times and it will run through some codes on the dash. 💯🤝
@@colin7761 i appreciate you bro I'll comment the codes
@@colin7761 scanner says p0137 but not sure if that's the reason speedometer don't move at all what do you think? I have the abs light on traction control and the esp bas they are all on please help
Do you know what sensor measures Engine Torque and Converted Engine Torque in these transmissions? I have a 2011 Challenger stuck in limp mode. I am getting a reading 48000 lbs of torque
I’ll look into it bro! What codes are you getting?
@@colin7761 no tcm codes, just one from the PCM for a cylinder 5 misfire (bad plug is my guess) car had been sitting around for about 4 years so. Changed the out the fuel pump and battery so I could get it to turn on. Power steering pump also had gone out so I changed that out too. A new MAP sensor as well. Planning to see in the future if a transmission fluid change would help. Fluid looks clean and at proper level but smells a bit off.
Right on bro! What scanner are you using? Is it capable of reading tcm codes. If you are able to get live data, does the wheel speed sensors give a proper readout while they are spinning? Also I would def address the p0305 next. Try swapping the coil pack out with another cylinder. If the misfire changes then it’s the coil pack. If no change, then pull the plugs next to see what they look like 💯💯 After the p0305 is fixed then you should focus on the other issues. Anyway bro, good luck with that and if you need any advice you know where to go!! If your transmission fluid is old and dark, it would probably be a good idea to replace soon too 💯💯🤝
Hello bro , ive had a speed sensor issue once, mine was just a pin on the connector but right now I am still stuck in limp mode from p0758 and p0522 im really freakin stuck there for a month
When I had the speed sensor issue I could clear the codes and it would shift right away but right now it wont shift no matter what
Hey bro, appreciate the comments. Give me some time to look into it and I’ll get back to you here soon.. 💯💯🤝
I have the same code, replaced the cond plate and i still have the same issue? Checked all my wires seem fine what can be another cause??
Sorry to hear that bro! What codes are coming up?
P2767
My car wont go pass 35
How’s the connector on the trans? Do you know where the TCM connector is as well?
@@colin7761where is the TCM connector? We replaced the conductor plate. Still get the p0717 and P0717pd. But not every time we drive it. Checked the wires and connection at the conductor plate. Everything appears to be in good shape/condition.