After installing a completely new caliper and new brake pads for the front left and right. As well as replacing the rear pads. Now I can’t move my 08 grizzly 660 when it’s in neutral. What might I have done wrong?
I've seen and I am experiencing the same issue that Robert and Nathan mentioned below. The brakes bleed as per normal and work well, but the back brakes do not seem to bleed properly and remain soft, if not immediately they definitely soften over a long ride. I've searched and seen lots of forums on this with the 700 Grizzly's. Any tricks to correct this, or typical system parts that are diagnosed as the problem? Thanks in advance!
Having trouble bleeding my brakes on a 2012 Grizzly 700 , for some reason I just can't get them to get any pressure ? I'm referring to the rear brakes that is .
I normally work on mowers, but am taking in a few ATV's. This Yamaha I just took in for a carburetor replacement, and now a rear brake job. The location of the vin number (left front frame, in fenderwell) has rubbed so much there's no ID left. Is there another way to ID this mower? Customer says it's a 2012.
My apologies! Let me correct my original statement. The front brakes bleed as they normally would successfully. It's the back brakes that do not bleed as per statement below. Thanks.
I have to pump my brake handle 5 or 6 times then my brakes come back then the next day it will randomly do it again ill pump it 5 or 6 times then I have brakes again any idea to what is causing my brakes to randomly stop working
@@darrell5363 Same here. IDK what's with these 700 Grizzly rear brake systems. Very difficult to set up once maintenance is completed. Mine still get soft over a day of riding and aren't great when cool either. Any hints or corrective actions would be greatly appreciated.
doesn't yama have two brake fluid reservoirs...? you did not mentioned which you are using or maybe one on each side....little more details would be great...
Didn't know if bleeding brakes from my truck would translate to quad super helpful for those who don't know how to bleed. Well put.
Thanks for the help!
After installing a completely new caliper and new brake pads for the front left and right. As well as replacing the rear pads. Now I can’t move my 08 grizzly 660 when it’s in neutral. What might I have done wrong?
What about the back?
I've seen and I am experiencing the same issue that Robert and Nathan mentioned below.
The brakes bleed as per normal and work well, but the back brakes do not seem to bleed properly and remain soft, if not immediately they definitely soften over a long ride. I've searched and seen lots of forums on this with the 700 Grizzly's. Any tricks to correct this, or typical system parts that are diagnosed as the problem?
Thanks in advance!
trying to figure this out on my 16 grizzly the brake pedal easily touches the grip and i slowly stop, should lock up the wheels
Zillaman you are the daddy :) Thank you
Is there a different master cylinder for the rear brakes?
Yes.
Yes it’s on a grizzly 660 by the front right tire down low. In fact I think it’s lower then the rear caliper making it more difficult to bleed
Having trouble bleeding my brakes on a 2012 Grizzly 700 , for some reason I just can't get them to get any pressure ? I'm referring to the rear brakes that is .
same on my 16
I normally work on mowers, but am taking in a few ATV's. This Yamaha I just took in for a carburetor replacement, and now a rear brake job. The location of the vin number (left front frame, in fenderwell) has rubbed so much there's no ID left. Is there another way to ID this mower? Customer says it's a 2012.
My apologies! Let me correct my original statement. The front brakes bleed as they normally would successfully. It's the back brakes that do not bleed as per statement below. Thanks.
Foot brake is doing not much. Cannot find anything on this. Help?
I have to pump my brake handle 5 or 6 times then my brakes come back then the next day it will randomly do it again ill pump it 5 or 6 times then I have brakes again any idea to what is causing my brakes to randomly stop working
I’m having problems with my rear brakes where they barley grab
Same here did you figure out the problem? I’ve bled mine completely and nothing changed
@@nathansimpson5498 same
@@darrell5363 Same here. IDK what's with these 700 Grizzly rear brake systems. Very difficult to set up once maintenance is completed. Mine still get soft over a day of riding and aren't great when cool either. Any hints or corrective actions would be greatly appreciated.
@@timlewis5937my brake lever touches the handle grips and I slowly roll to a stop
My 1999 yamaha kodiak locks up all 4 tires so I know theirs def a issue here
What about the rear brakes?
What about the rear brake?
Pressed the rear brake down while the caliper was off the rotor. Is bleeding the brakes the only way to get them back open?
You need to push the piston back into the caliper. Use a vise clamp
Awesome video
yeah, it does have two, left one for a rear brake..
Thank you
doesn't yama have two brake fluid reservoirs...? you did not mentioned which you are using or maybe one on each side....little more details would be great...
There are two reservoirs. One for front brakes and one for rear. Right side is for front and left side is for rear.
What size hose is he using
1/4" inner diameter
Thanks super helpful!
One important question is do you know JESUS CHRIST AS YOUR PERSONAL LORD AND SAVIOR?
obviously
My brake completely exploded into a million pieces