Thank you! I needed to screw it in a little more, but I didn't know how I could reach it! I didn't know you could just pop a ledge off like that on the base!
I literally owe you, I accidentally dropped my square 1 and it's middle layer and one of the corners shattered into pieces, I tried to join the corner but it wasn't just fitting and I thought I'd lose it forever, your video helped me a lot, RUclips was a real life saver. You deserve a sub
i still havent lerned the algorithms for square-1 completely i know a / turn idk if theres a \ turn and i know 1 2 3 4 turns and -1 -2 -3 -4 turns idk if i know it or not i forgot hehe
In case people happen to need this information, if you have the original North America Square 1 (green/white/red/blue/yellow/orange), the main axle adjustment screw is on the yellow side, pretty much directly behind the Q of the Square 1 sticker.
dang, im just a kid and with my chrismas money i bought my first sq1 for 40$ and your video made me break it, i hope you are happy now. i loved your chanal but i guess you dont care about me
Easy. Break off one half of the circle, make half of the layer, and turn it then do / (move up twice). Then slide half of the layer into the piece, do / again, and slide the half onto the other side, /, and then 2 layers will be fixed. There should be a half of a circle, so place the four pieces there, then get the other half circle, place the four remaining pieces onto that, put the half circle in, and press down on those pieces. Hopefully this fixed your cube!
Thanks for this video, my Qiyi suddenly became very loose for no reason. I didn't know you can pop out the middle layer and adjust the screw to tighten it again.
So I was in the middle of a solve and it popped (qiyi) and it was scrambled when I put them back in could I just put it back together ( solved) and have it be fine or should I put the pieces in randomly and see what happnea
Yes, I am very sure. But if you want to be more careful, loosen the screw on the side a couple of wrist turns, then you can pull an entire edge out, then do the method he shows with the corners.
I just got my first squere-1 i desembled it ... and when i put it together it fellt like turning a cube bith no core,idk how to explay it just feall like its without spirings or screavs .... some one can hellp ?
They all do come apart. If you're not willing to force them apart, you can save those edges until last and you'll still be able to reassemble it normally.
Well, I have a Calvin's puzzle Square-1. Not to be a turd or anything, but it DOES come apart differently. You have to either pull it apart, pull out one of the edges, then repeat, then do the corners, or you can solve it too fast and pop it.
can someone help me please my blue and green are on the wrong side lol I might just be dumb but the blue is to the right of orange and green is on the leftor does it not matter
I CANT REASSEMBLE IT HELP Edit: I put it back together, but for some reason one layer is looser and when I do a slice move, it gets even looser. I tried tightening it but nothing happened. I NEED MORE HELP (Note: this was happening before i disassembled it. I assumed my classmate screwed up the tensions or whatever but that's not what happened)
Are you talking about the upper/lower layer or the slice layer? On the two opposite layers, you’ll sometimes find a small screw perpendicular to the main one that holds them in place. On the slice layer, core stripping is a big problem on a lot of older square-1’s that unfortunately can’t be fixed very easily, t other than just avoiding making the cube too loose.
The Man Behind The Camera i very much like my MoYu weilong square one, ITS SO MUCH BETTER THAN MY STICKERLESS QIYI SQUARE ONE LOL BEST OF ALL, The moyu weilong square 1 sticker dont have any problems, the stickers r 1000000% amazing!!!!
How to disassemble a cubetwist or shengshou. Step 1 do the parity algorithm as fast as you can turn it
Maybe you Mean fast as impossible
@@auf3428 yes fast as impossible 😎
I just popped my qiyi like this. I CAN'T put this shit IN
who came here to fix a pop
I came here because my friend accidentally broke it lol
I did
Me
I don’t know how to fix it still
My brain hurted so I wanted to
thanks so much my square 1 fell apart and u helped me
Literally same
Thank you! I needed to screw it in a little more, but I didn't know how I could reach it! I didn't know you could just pop a ledge off like that on the base!
i got a yj mgc sqaure 1 and i didnt know how to take it apart (it was my first sqaure 1) so i found you and your very underrated!
I literally owe you, I accidentally dropped my square 1 and it's middle layer and one of the corners shattered into pieces, I tried to join the corner but it wasn't just fitting and I thought I'd lose it forever, your video helped me a lot, RUclips was a real life saver. You deserve a sub
I’m trying but it’s not working
@@xerxeszoo4691 ???? brain.exe not found wth??
I love how you always come up with a new idea for each video!
Yeah, unfortunately I didn't have much time so it wasn't very exciting. :/
It’s not working
i broke my sqaure 1 doing this. godamnit
Same
Same
It probably works better with other square 1s then
Same
I’m not gonna try I’m just watching this
im late heres a joke
Parity Alg
Whale FX only if u know csp
HOlY CARP that’s spooky
that's not a joke that's just plain out scary
i ordered a square 1 yesterday so im just waiting to use this tutorial also this is just a fun fact your one of my favorite rubiks cube youtubers
i still havent lerned the algorithms for square-1 completely i know a / turn idk if theres a \ turn and i know 1 2 3 4 turns and -1 -2 -3 -4 turns idk if i know it or not i forgot hehe
In case people happen to need this information, if you have the original North America Square 1 (green/white/red/blue/yellow/orange), the main axle adjustment screw is on the yellow side, pretty much directly behind the Q of the Square 1 sticker.
Thank you so much, my cube is now broken:(😤😤
Ur other vids r so much better though!
You made me happy back😊
dang, im just a kid and with my chrismas money i bought my first sq1 for 40$ and your video made me break it, i hope you are happy now. i loved your chanal but i guess you dont care about me
Do you know how to assemble the Square-2?
It should work basically the same way, just with two corner pieces where there would be one on a square-1.
legoboyz3! Thanks:)
Wait is that a real thing or is this a joke lmao
WikoTheCuber no it’s a real thing. It’s like a harder version of square 1
@@peytonwest7876 joke
could you make a tutorial for the moyu ones? i have a moyu and it has weird slots and i cant fit it in to the core
So my square 1 it white centered but isn't a speed cube with a bigger middle part making it hard to put the corners back in
Without unscrewing, is there any way to reattach a corner if that's the last peace?
Hello person reading the comments have a very good day.
Thanks, helped me.
this helped me solve my sqr 1 xD
okay WHAT? this was recommended to me just after I disassembled and reassembled my square 1...
Right when I clicked on this video I fixed the pop! My first square one pop.
How do you do it with the mfsq1
Yeah...
Benjamin Singh no, it’s made by moyu... qiyi made the QiFa
Easy. Break off one half of the circle, make half of the layer, and turn it then do / (move up twice). Then slide half of the layer into the piece, do / again, and slide the half onto the other side, /, and then 2 layers will be fixed. There should be a half of a circle, so place the four pieces there, then get the other half circle, place the four remaining pieces onto that, put the half circle in, and press down on those pieces. Hopefully this fixed your cube!
Thanks for this video, my Qiyi suddenly became very loose for no reason. I didn't know you can pop out the middle layer and adjust the screw to tighten it again.
River Capulet same! Mine crumbled before i could figure it out though
What about for the little magic? Is it the same for the sticker less one you showed in the vid? I don’t want to break mine
So I was in the middle of a solve and it popped (qiyi) and it was scrambled when I put them back in could I just put it back together ( solved) and have it be fine or should I put the pieces in randomly and see what happnea
I attempted to disassemble my qiyi square 1. When I put it back together, the piece to the edge continued falling out.
SAME! I dropped my qiyi square 1 on the carpet and an edge piece popped out. Now the piece won’t stay in - it keeps falling out.
None of the pieces on my Qiyi sq1s will split. I want to split them to swap the caps. Can anyone help?
how do you put in the corner pieces for a qiyi square-1 cause mine does not come apart
My brain wasn't hurting enough after watching a solve so I came here
What about x-man volt
same thing
Npuzzle you sure because i am really scared to take it apart
Yes, I am very sure. But if you want to be more careful, loosen the screw on the side a couple of wrist turns, then you can pull an entire edge out, then do the method he shows with the corners.
DONT!!! I tried and some pieces SNAPPED! I was so mad. Had to buy another one.
Rubik Geek you could have bought a replacement part(s)
I just got my first squere-1 i desembled it ... and when i put it together it fellt like turning a cube bith no core,idk how to explay it just feall like its without spirings or screavs .... some one can hellp ?
Set the tensions
R/ihadastroke
This was practically a cube twist square-1 roast
Only two of my qiyi edges split and there both yellow so how do I do the white side or how can I split the edge
They all do come apart. If you're not willing to force them apart, you can save those edges until last and you'll still be able to reassemble it normally.
i got a qiyi square one recently and my top and bottom faces are loose. What should I do?
There's only one way to tension it, which is in the center layer. Are you sure it's looser than normal?
Yes when I try to turn it it spins
Yes when I try to turn it it spins
Did not work for me....
thx man now I konw what to do when my sq1 pops !
Cool video!
cant get it together :(
⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻⸻ ？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？？
Does this work on the Yuxin Little Magic?
Glass of Milk
YOU ARE FAMILIAR
HMM IS IT THAT
Mega unboxing and the to do list from tingman?
If it is ayy m8
Can you assemble and disassemble a gear cube
help please my square 1 is very loose now i assembled what i do i?
Is the qiyi the same as the weilong square one
I'm not sure, I don't have one.
legoboyz3! Oh ok
Well, I have a Calvin's puzzle Square-1. Not to be a turd or anything, but it DOES come apart differently. You have to either pull it apart, pull out one of the edges, then repeat, then do the corners, or you can solve it too fast and pop it.
I'm still liking the video though.
Tysm! This 100% works!
can someone help me please my blue and green are on the wrong side lol I might just be dumb but the blue is to the right of orange and green is on the leftor does it not matter
I'm a year late but do /(6,6)/
Thanks, I accidentally removed 2 edge pieces when I was experimenting with illegal slices (slices with 7 or 5 units)
I just tried taking out a. Peice and I guess it was connected to the core and now the peice is broke 😭😭 and it’s my only square one I’m so sad
square one force cubes
how will it be possible
It's not.
No. You would need stickerless square-1's produced with different top/side colors, which no companies make.
maybe spray painting will work
lol, that would literally completely defeat the purpose of a force cube.
Maybe a random company that will make a square one that has a weird color scheme
Imma using this to make a 1x1x2 square 1 that I saw
This broke my xman squan ☹️
F
My Square 1 broke too :(
same and i got it yesterday but i think glue will fix it
Marshall Pieri yea, it worked with mine
@@Angel-kx9ij what kind of glue worked?
what about the calvin's and faxin
Thanks ❤
Is it really supposed to be wobbly and stuff, and very loose
I just wanted to know how it works and turns.
Can you do How to solve Megaminx or Pyraminx (if you have done already i just didnt know)
+XReviewer - Cube Reviews Thanks !!
I broke my cube trying to do this
same
Thank god I was so scared because I was getting ready to solve my square 1 for the first time and right before I started the scramble... POP
Can you please make a square 1 tutorial.
How to do the MFSQ1
good to know man :D
Hi
Thank you
Thank for the video because my friend broke his
What about the cubing classroom squan
I cant assemble the center piece of qiyi.
Ikr!
same!
Now I understand how to assemble after a thousand attempts :P
are you talking about the core because i have no clue where the white nut and the black piece go....
I cant get the pieces back in
#StopcubeViolence
but you can put it back together
Or can you...
Mate what if it's REALLY tight
You broke my cube?
thanks a lot!
what about the MoYu Weilong
I can't take my pieces apart and the other one don't work
I can’t put the last piece
I CANT REASSEMBLE IT HELP
Edit: I put it back together, but for some reason one layer is looser and when I do a slice move, it gets even looser. I tried tightening it but nothing happened. I NEED MORE HELP
(Note: this was happening before i disassembled it. I assumed my classmate screwed up the tensions or whatever but that's not what happened)
Are you talking about the upper/lower layer or the slice layer? On the two opposite layers, you’ll sometimes find a small screw perpendicular to the main one that holds them in place. On the slice layer, core stripping is a big problem on a lot of older square-1’s that unfortunately can’t be fixed very easily, t other than just avoiding making the cube too loose.
@@Z3Cubing Sorry for bothering you, I fixed it hehe...
Mine has a different mecahnisem plz hep
i like how hes called legoboys but he does rubiks cubes lol
Appreciate you telling us how to do this but these methods dont work for me
Storyline of my Square 1:
I bought my square one.
I mix it up.
I try to solve it.
I can't figure it out so I take it apart.
I broke my square 1.
Subtitles be like:hey guys it’s sigle boys you three today......
Thank a lot now my square 1 is broken🤬🤬🤬
Why did u dissasembale it on purpose
Nice grammer
5.85987448205 haha, you wrecked him
Mine too
may I fix it?
ty
The part where you take it apart works.....but not the putting it back together part;(
dued to somebody bow my square one is broken
tried, broken edge pice :(( 2 deys old cube :((((((
rip cube
Why does every cubing youtuber (including you) have stickerless square-1s?
+Akash Malajpure That's why I got Stickerless too.
Stickerless is not good for me because all the sweat from your hands dry onto the surface of your cube making it very sticky.
The Man Behind The Camera i very much like my MoYu weilong square one, ITS SO MUCH BETTER THAN MY STICKERLESS QIYI SQUARE ONE LOL BEST OF ALL, The moyu weilong square 1 sticker dont have any problems, the stickers r 1000000% amazing!!!!
I cant Split the Edges
Doesn't work on my moyu
My X-Man Volt Snapped.
do company spotlight please please
Calvins?
This would be more useful if I had a square 1
what bout the guan squan
My square 2 popped lmao
thank yooouuuuuuuu
thanks you Soo much
Here 1 sub
Did someone notice?... His qiyi square has a wrong orientation... The white and yellow must be flipped... Watch carefully and compare both the cubes
Some people like the white color on top, depending on how they can easily recognize colors.
You can just unscrew the screw
Who came here because you can't solve a square 1
Mine is a yongjun