We kindly remind you to thoroughly clean the electrode before calibration. Additionally, it's essential to use fresh calibration solutions for accurate results. Should you require further information or assistance, please don't hesitate to reach out to us at info@gainexpress.com with your order ID. Thank you!
"Regarding calibration, we recommend calibrating the pH every 2-3 days if the product is used frequently " seriously ? that buffer solution is not free
For tds/ec/salt do i have to calibrate it only with 1413 and 12.88 conductivity solution? Or do i have to calibrate seprately for ec, tds, salt respectively using other calibration solution ?
Hello! You'll be pleased to know that there's no need for separate tds/ec/salt calibrations. Just a single calibration solution will suffice to ensure your equipment is properly calibrated. Just calibrate the EC for a hassle-free calibration process.
to Calibrate the TDS, Instead of PH solution, use conductivity buffer solution ( 1413uS, 12.88ms, or 111.8ms) ex. you have 1413uS buffer solution. 1. Change the mode into EC 2. Immerse the meter into the 1413uS buffer solution. 3. Long press MODE/CAL to enter the calibration mode. 4. Wait until 1413 flashes 3x, and that's it. the calibration is done. you may now clean the probe with distilled water and dry it.
@@GainExpress hello. I tried this. The meter shows about 1600 instead of 1413, so it is not correct calibrated. If I press cal, it blinks, but afterwards it's still in the same range. I had about 21°C. What's wrong?
@@auroraglacialis Hello! Please try immersing it in distilled water for 5 minutes, dry it with a paper towel, and recalibrate it with a brand new 1413µS/cm calibration solution. If the problem is still the same, please contact us at info@gainexpress.com and provide us with your order ID. Our technical support team will assist you in resolving the issue. Thank you.
I take it from other ppl's questions in the comments and the response, that there are just 2 different calibrations needed for this device. 1. Calibrating the PH, like shown in this video and 2.) Calibrating the EC, which they say will also take care of " tds/ec/salt calibrations". This looked to be the answer about calibrating EC, but was response asked about TDS. I see it at Amazon saying for calibrating tds/ec/salt calibrations 5 in 1, $11.99 for 4 Bottles of 50mL. "to Calibrate the TDS, Instead of PH solution, use conductivity buffer solution ( 1413uS, 12.88ms, or 111.8ms) ex. you have 1413uS buffer solution. 1. Change the mode into EC 2. Immerse the meter into the 1413uS buffer solution. 3. Long press MODE/CAL to enter the calibration mode. 4. Wait until 1413 flashes 3x, and that's it. the calibration is done. you may now clean the probe with distilled water and dry it."
I see now from your profile that you might be in New Zealand, so idk about Amazon there, but the same seller has all three of these 1413uS, 12.88ms, or 111.8ms for the same price and all are for the same quantity of 4x 50ml bottles.
Hi Mopar, if the item is brand new no need to calibrate, it has been pre-calibrated at the factory. for pH calibration, use the pH buffer solutions for tds/ec/salt calibrations, Just a single calibration solution will suffice to ensure your equipment is properly calibrated. Just calibrate the EC for a hassle-free calibration process.
Hello! Were you looking for information on how to calibrate it? If so, you can find the calibration procedure in the operation manual. Please follow this link: cd50.net/303/, and it will direct you to the operation manual where you can find detailed instructions on calibration. If you have any more questions or need further assistance, please feel free to reach out to us at info@gainexpress.com. Thank you!
Hi, This is how to calibrate but how to test the pool water and what should each ideal reading level should be, Also if we have to calibrate after each use or even 5 uses then going back to liquid testing kit is the go. Thanks
Thank you for your interest in our product. You can take a sample of water from the pool to measure the PH/TDS/EC/Salinity/TEMP levels. However, it's important to note that each country has its own standard level of these parameters, so please check the standard in your country. Regarding calibration, we recommend calibrating the pH every 2-3 days if the product is used frequently. Normally, there is no need to calibrate TDS/EC/Salinity. However, if you find that the readings are not accurate, then calibration may be necessary.
@@enzeypogi you can calibrate it with any brand of standard solution. It's quite versatile in that regard, so feel free to use whichever brand you prefer for calibration. also there's no need for separate tds/ec/salt calibrations. Just a single calibration solution will suffice to ensure your equipment is properly calibrated. Just calibrate the EC for a hassle-free calibration process.
Hello, you can calibrate it with any brand of standard solution. It's quite versatile in that regard, so feel free to use whichever brand you prefer for calibration.
Hello! You'll be pleased to know that there's no need for separate tds/ec/salt calibrations. Just a single calibration solution will suffice to ensure your equipment is properly calibrated. Just calibrate the EC for a hassle-free calibration process.
Hi Hasan, you may rinse it with distilled water before and after you use the meter. And if the meter has been idle for a long time, you need to calibrate it.
to Calibrate the TDS, Instead of PH solution, use conductivity buffer solution ( 1413uS, 12.88ms, or 111.8ms) ex. you have 1413uS buffer solution. 1. Change the mode into EC 2. Immerse the meter into the 1413uS buffer solution. 3. Long press MODE/CAL to enter the calibration mode. 4. Wait until 1413 flashes 3x, and that's it. the calibration is done. you may now clean the probe with distilled water and dry it.
Hi nova, to Calibrate the TDS, Instead of PH solution, use conductivity buffer solution ( 1413uS, 12.88ms, or 111.8ms) ex. you have 1413uS buffer solution. 1. Change the mode into EC 2. Immerse the meter into the 1413uS buffer solution. 3. Long press MODE/CAL to enter the calibration mode. 4. Wait until 1413 flashes 3x, and thats it. the calibration is done. you may now clean the probe with distilled water and dry it.
I went out looking for lr44 they said there is nothing like that in their various stores. Do you have alternative? Can CR2016 work? I see that everywhere.
Need operating instructions for a beginner, not calibration. First, HOW TO USE to conduct each test.
What if the reading didn't match the buffer solution in the calibration?
I'd like an answer for this too
We kindly remind you to thoroughly clean the electrode before calibration. Additionally, it's essential to use fresh calibration solutions for accurate results. Should you require further information or assistance, please don't hesitate to reach out to us at info@gainexpress.com with your order ID. Thank you!
"Regarding calibration, we recommend calibrating the pH every 2-3 days if the product is used frequently " seriously ? that buffer solution is not free
How long Last 1 Electrode Probe ? ❗
Why the pH value is buffering and dont become stable after rinsing it with distilled water? It is not showing accurate value. How can i solve this?
For tds/ec/salt do i have to calibrate it only with 1413 and 12.88 conductivity solution? Or do i have to calibrate seprately for ec, tds, salt respectively using other calibration solution ?
Hello! You'll be pleased to know that there's no need for separate tds/ec/salt calibrations. Just a single calibration solution will suffice to ensure your equipment is properly calibrated. Just calibrate the EC for a hassle-free calibration process.
Do I also need to calibrate the tds and EC?
to Calibrate the TDS, Instead of PH solution, use conductivity buffer solution ( 1413uS, 12.88ms, or 111.8ms) ex. you have 1413uS buffer solution.
1. Change the mode into EC
2. Immerse the meter into the 1413uS buffer solution.
3. Long press MODE/CAL to enter the calibration mode.
4. Wait until 1413 flashes 3x, and that's it. the calibration is done.
you may now clean the probe with distilled water and dry it.
@@GainExpress hello. I tried this. The meter shows about 1600 instead of 1413, so it is not correct calibrated. If I press cal, it blinks, but afterwards it's still in the same range. I had about 21°C. What's wrong?
@@auroraglacialis Hello! Please try immersing it in distilled water for 5 minutes, dry it with a paper towel, and recalibrate it with a brand new 1413µS/cm calibration solution. If the problem is still the same, please contact us at info@gainexpress.com and provide us with your order ID. Our technical support team will assist you in resolving the issue. Thank you.
do you need to calibrate this if you bought brand new or is it already calibrated at the factory
Hi Mopar, this item has been pre-calibrated at the factory.
How to adjust EC TDS and SALT please?
do you calibrate EC?
I take it from other ppl's questions in the comments and the response, that there are just 2 different calibrations needed for this device.
1. Calibrating the PH, like shown in this video
and
2.) Calibrating the EC, which they say will also take care of " tds/ec/salt calibrations".
This looked to be the answer about calibrating EC, but was response asked about TDS. I see it at Amazon saying for calibrating tds/ec/salt calibrations 5 in 1, $11.99 for 4 Bottles of 50mL.
"to Calibrate the TDS, Instead of PH solution, use conductivity buffer solution ( 1413uS, 12.88ms, or 111.8ms) ex. you have 1413uS buffer solution.
1. Change the mode into EC
2. Immerse the meter into the 1413uS buffer solution.
3. Long press MODE/CAL to enter the calibration mode.
4. Wait until 1413 flashes 3x, and that's it. the calibration is done.
you may now clean the probe with distilled water and dry it."
I see now from your profile that you might be in New Zealand, so idk about Amazon there, but the same seller has all three of these 1413uS, 12.88ms, or 111.8ms for the same price and all are for the same quantity of 4x 50ml bottles.
I think I got a dud. The temperature and PH results jump around and when I calibrated the 9.18 solution showed as 6.86
Hi Ben, can you email us at info@gainexpress.com together with your Order ID. Thanks
Good day! Do i need to calibrate all the parameters or only pH?
Hi Mopar, if the item is brand new no need to calibrate, it has been pre-calibrated at the factory.
for pH calibration, use the pH buffer solutions
for tds/ec/salt calibrations, Just a single calibration solution will suffice to ensure your equipment is properly calibrated. Just calibrate the EC for a hassle-free calibration process.
Would you please tell me the reset procedure? It will be wonderful if you can provide a video on how to reset it.
Hello! Were you looking for information on how to calibrate it? If so, you can find the calibration procedure in the operation manual. Please follow this link: cd50.net/303/, and it will direct you to the operation manual where you can find detailed instructions on calibration.
If you have any more questions or need further assistance, please feel free to reach out to us at info@gainexpress.com. Thank you!
Hi, This is how to calibrate but how to test the pool water and what should each ideal reading level should be, Also if we have to calibrate after each use or even 5 uses then going back to liquid testing kit is the go. Thanks
Thank you for your interest in our product. You can take a sample of water from the pool to measure the PH/TDS/EC/Salinity/TEMP levels. However, it's important to note that each country has its own standard level of these parameters, so please check the standard in your country.
Regarding calibration, we recommend calibrating the pH every 2-3 days if the product is used frequently. Normally, there is no need to calibrate TDS/EC/Salinity. However, if you find that the readings are not accurate, then calibration may be necessary.
@GainExpress to calibrate EC, can I use aquadest or do I need some special solution and whaf is it?
After the ph calibration is the tds is also calibrated or do i need another buffer powder to calibrate tds?
Yes, you need another solution to calibrate the TDS
@@GainExpress thank you so much
What solution is needed to calibrate tds and ec?
@@enzeypogi you can calibrate it with any brand of standard solution. It's quite versatile in that regard, so feel free to use whichever brand you prefer for calibration. also there's no need for separate tds/ec/salt calibrations. Just a single calibration solution will suffice to ensure your equipment is properly calibrated. Just calibrate the EC for a hassle-free calibration process.
Is it okay to calibrate it with adwa ad70030 ec standar 12880 uS/cm solution to calibrate it? Or do i have to use any specific 12.88 solution?
Hello, you can calibrate it with any brand of standard solution. It's quite versatile in that regard, so feel free to use whichever brand you prefer for calibration.
How much water do I add to the packets
Hi Jared, dissolve in 250ml of distilled water each pack.
@@GainExpressr u sure its 250ml of water???in the video it doesnt look like 250ml
bought one on ebay and I can't get a stable ph reading on it, is my electrode broken? where do I get replacement electrodes?
Hi Neville, may I know your Order number?
What for kind of solution for tds ?? To calibrate
Hello! You'll be pleased to know that there's no need for separate tds/ec/salt calibrations. Just a single calibration solution will suffice to ensure your equipment is properly calibrated. Just calibrate the EC for a hassle-free calibration process.
Kindly do this process after each use? Or just in the beginning and then I can use it several times
Hi Ahmed, you can only use the solution one time.
Hi. Do we need to calibrate it again in further usage?
Hi Hasan, you may rinse it with distilled water before and after you use the meter. And if the meter has been idle for a long time, you need to calibrate it.
@@GainExpress can you purchase the calibration solution packages ?
Do i need to buy different solution to test salinity? They only provide ph solution
Yes, you need to buy a separate solution to test salinity. Only the pH solution is provided.
@@GainExpress Why? That is so frustrating
Do we need to calibrate for salinity?
Do I need calibration for new device?
Hi, This Model has been pre-calibrated at the factory.
The ph number keep jumping and not in 0 when I bought it. Is it normal?
Hi Chang, can you email us at info@gainexpress.com together with your Order ID. Thanks
How to calibration tds ?
to Calibrate the TDS, Instead of PH solution, use conductivity buffer solution ( 1413uS, 12.88ms, or 111.8ms) ex. you have 1413uS buffer solution.
1. Change the mode into EC
2. Immerse the meter into the 1413uS buffer solution.
3. Long press MODE/CAL to enter the calibration mode.
4. Wait until 1413 flashes 3x, and that's it. the calibration is done.
you may now clean the probe with distilled water and dry it.
@@GainExpress thanks!!!!
How to calibrate TDS??
Hi nova, to Calibrate the TDS, Instead of PH solution, use conductivity buffer solution ( 1413uS, 12.88ms, or 111.8ms) ex. you have 1413uS buffer solution.
1. Change the mode into EC
2. Immerse the meter into the 1413uS buffer solution.
3. Long press MODE/CAL to enter the calibration mode.
4. Wait until 1413 flashes 3x, and thats it. the calibration is done.
you may now clean the probe with distilled water and dry it.
when I calibrate with the 3 envelopes in all I get 6.86 :(
@@matiasaranda6405 me too
@@matiasaranda6405 did you fix bro?
Please can you give me the battery number for replacement?
Hi, it uses 3 x 1.5V (LR44) button size battery
@@GainExpress Thank you so much,will buy today
I went out looking for lr44 they said there is nothing like that in their various stores.
Do you have alternative?
Can CR2016 work?
I see that everywhere.
@@cyprianokpalaku8770 CR2016 is thinner compare to LR44, it might not fit in the battery compartment, I suggest to use LR44
Wow to reset it?
the Item has been pre-calibrated at the factory. if the item has been idle for a long time, you need to calibrate it.
when I calibrate with the 3 envelopes in all I get 6.86
Hi Matias, Please message us your concern at info@gainexpress.com with your Order ID. Thank you
Does the temperature make that much of a difference to where my water temp is at 75 and it won’t climb past 6.03ph using the 6.86 cal?
Ŕŕŕ⁴
All 3 buffering solutions used but the meter shows lower numbers for each claiming accuracy +/-0.01
I have the same problem
White Michelle Johnson James Wilson Kimberly
Uma merda ,não segura a calibração
61810 Terry Junction