Pipe bending really does show the skill of the trade. Separates the men from the boys and your quite the man! especially with that beard. I'm impressed by the quality of your work and passion you put into your work. Keep it up. Keep the videos coming.
@@PlumbingDoctors yes you do but we all need a bit of help or reminder how to do things. I love bending pipe but always find a few tips in Derek's (TomKat's) videos.
Mistakes will always be made but its all about moving forward! I like to show REAL LIFE plumbing vids even if i fuck up as thats the best way to learn & grow 💯 👌
Thanks for posting brother.. Love your vids... real life plumbing & we've all been there with the bending😂😂😂...never used the liquid ptfe but will give it a go. Keep up the good work 👍🏾
Good work mate. I done same mistake many times rushing . This bender is nice tool just be carefull on tight bends close to each other you can mess up plastic guide. Or scratch it with end of the pipe.
A little tip, should always protect the pipe of the backplates through the wall, either wrap some tape around it or put some 22mm pushfit pipe over it and drill a bigger hole. stops it being eaten by cement etc
Really enjoy your videos Wasseem. Nice to see you don’t think you know it all and always willing to learn and improve. I use that liquid ptfe on rad tails but only if I can do it the night before as there’s nothing to say how long it takes to go off. Even with mains pressure and loose fit, how long did that tap take to cure and be watertight?
Salaam bro I’m currently at college doing my plumbing and heating. I’m looking for an apprenticeship, is there any chance I could my apprenticeship with yourself 😊 good videos keep posting as they a huge help whilst am at college👌
You should always sleeve copper pipe if it's going through a wall. Also you need to have a double check valve on your garden tap or have one inside to meet the water regulations.
@@PlumbingDoctors what a load of tosh. I used to enjoy watching your vlogs but you have ruined your rep in one. You’ve proved your good at making excuses. A check valve in a tap is only allowed when it’s a replacement not a new install.
Doing well but I would advise you have a look at some of TomKat's training videos on bending as they will give you some tips. ruclips.net/video/BXnJsV-Ryrw/видео.html
Best laugh i’ve had in ages😂
😀
Pipe bending really does show the skill of the trade. Separates the men from the boys and your quite the man! especially with that beard. I'm impressed by the quality of your work and passion you put into your work. Keep it up. Keep the videos coming.
Thanks i always try to do a good job! 😉
@@PlumbingDoctors yes you do but we all need a bit of help or reminder how to do things. I love bending pipe but always find a few tips in Derek's (TomKat's) videos.
Fair play to you mate showing your mistakes lol, very entertaining some great tips, very real, enjoy your work 👍 😀
Mistakes will always be made but its all about moving forward!
I like to show REAL LIFE plumbing vids even if i fuck up as thats the best way to learn & grow 💯 👌
Very informative, thank you very much.
Thanks
Your videos are getting good keep it up !
Safe bro
Nice to see you guys. Will start following u on tiktok 👍🏻 for more video
Thanks
Thanks great video, Loved the tutorial on bending. Thanks
👍🏼
Thanks for posting brother.. Love your vids... real life plumbing & we've all been there with the bending😂😂😂...never used the liquid ptfe but will give it a go.
Keep up the good work 👍🏾
👍🏼
Good work mate. I done same mistake many times rushing . This bender is nice tool just be carefull on tight bends close to each other you can mess up plastic guide. Or scratch it with end of the pipe.
👍🏼👍🏼
Can you make a video on how to find work please new in this field and struggling
Ok bro! 💯
What unvented cylinder is it ? Great videos
ariston 100l
I have vaillant ecotec plus 831 in center heating mode burner look like slow boiler very quiet slow running so how to set up please let me know
Thanks
Increase temperature on boiler
@@PlumbingDoctors thanks for reply the temperature allredey in fully mode .... it's d 0 mode is right or increase? Thanks
A little tip, should always protect the pipe of the backplates through the wall, either wrap some tape around it or put some 22mm pushfit pipe over it and drill a bigger hole. stops it being eaten by cement etc
Yh good tips there 💯
Wish i could find someone like you for my grandson, just finished level 3 plumbing now looking to go into gas
Thanks bro i appreciate the love
Good one bro
Thanks
Really enjoy your videos Wasseem. Nice to see you don’t think you know it all and always willing to learn and improve.
I use that liquid ptfe on rad tails but only if I can do it the night before as there’s nothing to say how long it takes to go off. Even with mains pressure and loose fit, how long did that tap take to cure and be watertight?
Thanks bro - i normally wait like 10 mins before filling the system
Salaam bro I’m currently at college doing my plumbing and heating. I’m looking for an apprenticeship, is there any chance I could my apprenticeship with yourself 😊 good videos keep posting as they a huge help whilst am at college👌
WS bro,
I appreciate the love but i already have an apprentice
No check valve or none return ? I always fit them unless I’ve missed you doing that
Not stated in MI so i have not fitted
It is a WRAS regulation and should be a double check valve and not in the tap unless a retrofit.
@@warrenprescott7955 there is a check valve on the combination valve?
Doesn't count, there has to be a double check valve between the isolation valve and where it goes outside as per the regs.
Not trying to put your work down just advising what the regs are.
Salaam br,
Could u pls send the link for the bender.
Thanks
WS bro...
Just search Monument Master Bender 15mm
@@PlumbingDoctors Allah rewards
ma sha allah
You should always sleeve copper pipe if it's going through a wall.
Also you need to have a double check valve on your garden tap or have one inside to meet the water regulations.
Never sleeved garden taps & the tap has a double check valve built in
@@PlumbingDoctors You can clearly see that the tap has no internal check valve imho
Brv you have more people respecting you than the Haters, so fuck em ya get me , Rubh Rakha
Respect yh i don't mind the haters they get me views lol
@@PlumbingDoctors good Point Brv… Hate no one ☝️
Bro you doing CM - MM OR inche's
CM & MM bro
Need a check valve on the inside pipework for the outside tap, bad video showing off cowboy antics.
Got check valve built in with the tap
@@PlumbingDoctors no check valve on that tap pal. You would see a small nut on the underneath of the tap.
@@Ian20232 yes your right ✅ good spot - We replaced the tap after we done the recording- this video was mad a good few months ago
@@PlumbingDoctors what a load of tosh. I used to enjoy watching your vlogs but you have ruined your rep in one. You’ve proved your good at making excuses. A check valve in a tap is only allowed when it’s a replacement not a new install.
@@Ian20232 😆 believe what u want i don't give a shit
Doing well but I would advise you have a look at some of TomKat's training videos on bending as they will give you some tips.
ruclips.net/video/BXnJsV-Ryrw/видео.html
I'll check it out when i find a spare min lol
muay8i
#vom.ong
🤕