You built it very nicely! I would like to make one comment: you have fixed one of the outputs of the differential. With this, you have reduced the ratio by half. It does not cut perfectly because the speed of the cutting roller is low. And the solution is right there in your hands: free the fixed output and simply weld the planetary gears of the differential inside. It will cut beautifully! Very clever!
Nice job. Impressive fabrication skills. I probably wouldn’t have thought of this myself if I designed this, but since the flails rotate the same direction as travel and the leading edge of the mower lays the grass down, it doesn’t cut tall grass so well it appears. Mowing in reverse in those conditions would work though.
Yooo I was just talking about this with my brother, but I was thinking of a flail mower that has the belt in the middle instead of the side. We go vineyard work and the belt on the side gets in the way of trying to mow closely to the vines. Also because most new vineyards are doing compact spacing and some try to do sustainable organic flail mower is very popular but like I mentioned most flail mowers are wide because of the belts on the side but it would be nice to have one where the belts are not in the way on either side. Just a thought and may you can make it happen. Also something else to design for vineyards is something to get rid of the weeds between each vine. There are a few but not much for compact tractors.
Masz rację. Ale spokojnie, mercedesowski most myślę że wytrzyma. Tym bardziej że dalej napęd jest realizowany przez paski klinowe które w ewentualności wyłapią drgania od wału tnącego który czasem się przyblokuje na jakimś kretowisku.
Bonjour, j'aimerais savoir si il serait possible d'avoir des plans, des cotes, des diamètres ? J'aimerais m'en fabriquer de 1m30 de largeur pour mon tracteur
nice build. the transfer case for the pto shouldn't be so tight it stops the flail immediately...these are made by manufacturers to spin down to reduce wear and tear and save your tractors rear pto box as well.
Buenas tardes excelente trabajo, pregunta tengo un rotovator, si le cambio las paletas que tiene, por unas cuchillas como la suyas ¿funcionara? Qué me dice usted, le agradecería su comentario, gracias de antemano salud.
Correct me if I'm wrong but are you not running through your spider gears by stopping the other side with that bracket welded to the frame? if you are they won't last long. Would be best if you took the diff apart and welded the spider gears together and took that bracket off on the other side of the diff. Other than that ,,,, great build!
More like professional made flail mower... well done sir 👏
You built it very nicely! I would like to make one comment: you have fixed one of the outputs of the differential. With this, you have reduced the ratio by half. It does not cut perfectly because the speed of the cutting roller is low. And the solution is right there in your hands: free the fixed output and simply weld the planetary gears of the differential inside. It will cut beautifully! Very clever!
o
Не оторвать взгляд ! Очень красивая работа !
Great job!! I have a CNC plasma table. Never mind buying one you made this look easy even by hand.
Nice job. Impressive fabrication skills.
I probably wouldn’t have thought of this myself if I designed this, but since the flails rotate the same direction as travel and the leading edge of the mower lays the grass down, it doesn’t cut tall grass so well it appears. Mowing in reverse in those conditions would work though.
Pretty interesting machine indeed, dude! Fantastic work!!! 😃
Stay safe there with your family! 🖖😊
Nice job .and high skills .you are great😊
That gearbox isn't ever gonna go out. Built like a tank! Nice job brother!
I like the round stock holder for cutting keys, very nice
sei un fenomeno certo gli attrezzi fanno il 50% ma sei un fenomeno di fabbrica...
Bardzo fajna kosiarka wyszła .
Pozdrawiam z okolic Krosna 😀.
A to co, on je Poljak?
Tak@@Cyclonut96
Most z W220 z dopiskiem "srebny" 🤣 dobitnie pokazuje u kogo nawet było kupione. Dobry śledczy moment by odnalazł która kasacja robi takie literówki.
Great skills well done🤠👍
16:24, did you buy this input shaft or you made/modified the shaft?
Yooo I was just talking about this with my brother, but I was thinking of a flail mower that has the belt in the middle instead of the side. We go vineyard work and the belt on the side gets in the way of trying to mow closely to the vines. Also because most new vineyards are doing compact spacing and some try to do sustainable organic flail mower is very popular but like I mentioned most flail mowers are wide because of the belts on the side but it would be nice to have one where the belts are not in the way on either side. Just a thought and may you can make it happen. Also something else to design for vineyards is something to get rid of the weeds between each vine. There are a few but not much for compact tractors.
I need to make one of these to groom the softball infield. Thanks for the inspiration! I'll need to learn to weld ! Thanks for the video
Great video! Thank you for sharing! More people should make their own equipment. Respect!
Расход металла ? Сортамент ? Стоимость оборудования ? Мастерская- маленький завод... + Правильные руки... Браво!
Zablokowanie półosi powoduje ciągłą pracę satelit.
Lepszą opcją jest zaspawanie mechanizmu różnicowego.
Masz rację. Ale spokojnie, mercedesowski most myślę że wytrzyma. Tym bardziej że dalej napęd jest realizowany przez paski klinowe które w ewentualności wyłapią drgania od wału tnącego który czasem się przyblokuje na jakimś kretowisku.
Small hint your top pulley needs to be a little bigger than the lower one, so you will have a higher number of revolutions on the mulcher
Hello mister beautifully made professionally done
Jak rozmiesciłeś mocowania młotków ?
Epic stuff... dimension would be greatly appreciated
What are the cutting blades called and how can I get them?
Mesin alat yg luar biasa mantap bos kembang kan terus ide kreatif
Nice job friend. Where can I find those hammer’s blades. What is their size.?
ebay has a selection of them
nicely done, but the belt was slipping, need a chaindrive.
Bonjour s'il vous plaît Quel est le diamètre du tube porte fleaux??
merci Super travail good job 👍
لا اعتقد انها جيده بما يكفي لكنك عملت بجد
Bonjour, j'aimerais savoir si il serait possible d'avoir des plans, des cotes, des diamètres ? J'aimerais m'en fabriquer de 1m30 de largeur pour mon tracteur
Is this a second channel for, made in Poland?
Yes it is 😉
You sir are a gifted individual. Did you make your very first spoon as a child?
nice build. the transfer case for the pto shouldn't be so tight it stops the flail immediately...these are made by manufacturers to spin down to reduce wear and tear and save your tractors rear pto box as well.
Swój chłop - pozdrawiam z RZE
Грудобій. Щоб косило то може розвернути його, спробувати рухатись задньою передачею?
Редуктор поменять местами, что бы прибавить обороты на мульчер. А то сейчас он просто гладит...
Но работа шикарная!
Просто розблокувати полуось і заварити диференціаціал
Не разорвет ли полуосевые шестерни.
Buenas tardes excelente trabajo, pregunta tengo un rotovator, si le cambio las paletas que tiene, por unas cuchillas como la suyas ¿funcionara? Qué me dice usted, le agradecería su comentario, gracias de antemano salud.
What are the main rotor tube dimensions?
1250 x 105 mm.
@@homemadeinventionsMIP thank you
Dyfer od S-Klasy?
jeszcze ze dwa kanały załóż i dawaj te same filmy na wszystkich.
Taki mam zamiar ;)
Very good craftemanship, but your idea of homemade and my idea of homemade are way different. Lol
Bravo
Set up makes spider gears do a lot of work. It would be better to reorient and weld spider gears.
The machine needs the rpm increase resulting from this. But you are right, a differential is not made for this purpose
Великолепно!
Хорошая работа , но трава остаётся , так не должно быть .
👍🏿👍🏿👍🏿
Digging the air over hydraulic bench vice.
MM77 Approved 👍🏼👍🏼
Correct me if I'm wrong but are you not running through your spider gears by stopping the other side with that bracket welded to the frame? if you are they won't last long. Would be best if you took the diff apart and welded the spider gears together and took that bracket off on the other side of the diff. Other than that ,,,, great build!
Amigo moro no Brasil tu poderia me passar as medidas
Молодец
It fails to flail in spots……. pity such a nice job.
🙂👏👏👏👍🙂
Добавить оборотов 3000 - 5000 и срезать будет всё.
chcelo by to ine zuby slaby vysledok
А трава все равно остаётся.
Bota concha para escavar vala em Trator
Made in poland
Whack a mole... !!
NOOOOOOOOOOOOOOOO
It exists since 1970 at the means!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Mz
Each one gave you. Haug