This video contains the full build of the IKEA Bekant Office Shelf. It is a great sturdy metal shelf about 53 inches tall and 47 inches wide. What do you think of the hat?
Thank you for taking the time to film this, prepares me well for what to expect as I’ll be building it on my own & I’m a bit of a lightweight these days. Very helpful
Much appreciated. I have not put any Ikea furniture together in close to 30 years. It made the task so much easier and quicker by following your video. All done. Just need to determine the shelf heights now.
I just bought this tonight and am so excited that you posted this video walking us through it! Appreciate the text in the bottom spelling out the steps. I can’t thank you enough!
Thank you! One note: the shorter leg is achieved by screwing in the long end into the leg, leaving the short stub to go into the base at the front center leg position. If, like me, you say ‘huh, all my legs are the same length’ and you’re tired because it’s now 11pm, you’ll end up puncturing the inside base once the leg is screwed in tight. D’uh! Sand, putty, paint.
This is a very sturdy shelf. I put a little wet dab of bar soap on the twist knobs and the shelf and it's much easier. There's a rail on the underside of each shelf for anti-sag, and a center front foot for anti-sag. I like it so well I'm glad I ordered two (same price for shipping). I wasn't sure of the build quality, but it's so good that i wish I'd bought the rolling side cabinet also to replace my current printer stand. The powder coating and edges are very smooth. I don't expect to snag any thing or cut my finger, etc. Note that the anti-sag bar under each shelf may take up a little vertical room, depending on what you want to slide onto the shelf below it. I put some other white IKEA storage boxes with only 1/2" to spare. So take that bar into account when you're measuring so you get it right the first time. (I couldn't figure out how to link my previous order to my IKEA account so I can't leave a review there. Hope this helps other people deciding...)
IMPORTANT!!!!!! If you are putting the legs on, make sure you pay attention and put the short one at the front. If you don't, the longer bolt will push through the board!!! (I took notice of this but somehow did it anyway!!!)
I have searched all over the internet to find its weight limit (by shelf) but I haven't come across any information. Would you happen to know? I wanna fill it with my comic books. Do you think it will endure the weight?
I don't know the weight limit but that could be pushing it a little bit since they are sitting on plastic pins. It's pretty strong though I think it could be close but to be certain I'd probably look for something like a metal shop shelf.
Is there a trick to get those little white pegs inside their hole in the boards? Especially the last one when putting the bottom shelf (the one on the middle). 14:11 Help!
thank you i followed every step. thank you for the help
Thank you for taking the time to film this, prepares me well for what to expect as I’ll be building it on my own & I’m a bit of a lightweight these days. Very helpful
Much appreciated. I have not put any Ikea furniture together in close to 30 years. It made the task so much easier and quicker by following your video. All done. Just need to determine the shelf heights now.
That's great I'm glad it helped.
I just bought this tonight and am so excited that you posted this video walking us through it! Appreciate the text in the bottom spelling out the steps. I can’t thank you enough!
Thank you! One note: the shorter leg is achieved by screwing in the long end into the leg, leaving the short stub to go into the base at the front center leg position. If, like me, you say ‘huh, all my legs are the same length’ and you’re tired because it’s now 11pm, you’ll end up puncturing the inside base once the leg is screwed in tight. D’uh! Sand, putty, paint.
This is a very sturdy shelf. I put a little wet dab of bar soap on the twist knobs and the shelf and it's much easier. There's a rail on the underside of each shelf for anti-sag, and a center front foot for anti-sag. I like it so well I'm glad I ordered two (same price for shipping). I wasn't sure of the build quality, but it's so good that i wish I'd bought the rolling side cabinet also to replace my current printer stand. The powder coating and edges are very smooth. I don't expect to snag any thing or cut my finger, etc. Note that the anti-sag bar under each shelf may take up a little vertical room, depending on what you want to slide onto the shelf below it. I put some other white IKEA storage boxes with only 1/2" to spare. So take that bar into account when you're measuring so you get it right the first time. (I couldn't figure out how to link my previous order to my IKEA account so I can't leave a review there. Hope this helps other people deciding...)
I could not figure out from the pictures in the manual which posts went in front and in back. Thanks for clearing that up!
Good job! 😎
THANK GOD FOR YOU SERIOUSLY YOU ARE A LIFE SAVER. YOUR VIDEO SAVED ME THE DIRECTIONS IN THE BOOK ARE SHIT.... SO TY VERY MUCH
Can’t wait to buy! Where do I buy the hook that you used to hang the headphones?
IMPORTANT!!!!!! If you are putting the legs on, make sure you pay attention and put the short one at the front. If you don't, the longer bolt will push through the board!!! (I took notice of this but somehow did it anyway!!!)
I have searched all over the internet to find its weight limit (by shelf) but I haven't come across any information. Would you happen to know? I wanna fill it with my comic books. Do you think it will endure the weight?
I don't know the weight limit but that could be pushing it a little bit since they are sitting on plastic pins. It's pretty strong though I think it could be close but to be certain I'd probably look for something like a metal shop shelf.
@@gwoyang thank you for the reply!!
@@AnastasiaBasta_MadQueen on the ikea website in the measurement tab, it says 110lbs (50kg) per shelf. Not sure if Ikea is strict on those or lenient.
I couldn’t get both back panels in...
It can be tricky to line up. Now that I've made two of them it's easier.
Could you build this without the mesh on the sides?
Unfortunately no. They are an essential part of the structure.
Is there a trick to get those little white pegs inside their hole in the boards? Especially the last one when putting the bottom shelf (the one on the middle). 14:11 Help!
OK I figured it out! In case anyone else is having trouble- I made the hole slightly larger with a kitchen knife.