Just did a build with this exact case and I was really impressed with it. Plenty of room. All the features made it very easy to add components. RGB controller built in. Excellent airflow. Three argb fans included. Cable management was good and it has a GPU brace built in. 3.5 drive case slides in and out with a click and single easy access case screw. The case and RGBs look really nice to. My only gripe was two of the panel screws where not threaded right and hard to screw in and out..Got this case at micro center in Indianapolis for 78 dollars on sale. For the price I give this case five stars.
Well it's up to personal preference when it comes to weight. I never take it into consideration to be honest. But the weight comes because there is a thicker steel which most cases in this price range category don't have. Anyways, thanks for the comment as always. :)
Oh, Cougar you were doing so well! Then I saw the separate front panel connectors. It's 2023 and the front panel layout is standardized. Why not have the single unified front panel connector?
BRAVO DARIO ❗Super kučište za tu cijenu. Ali što uraditi s 3-pin 5V Addressable RGB , kada MBO ima 4-pin utor ❓ Što je s kontrolom brzine okretaja ventilatora ❓ KANAL ti je već poduže pravo osvježenje u moru sličnih. Samo tako dalje 🤩
Hvala puno na ovom komentaru!!!! :) Svakako mi puno znači! Ako netko nema 3-pin 5V ARGB konektor na matičnoj, onda spoji fino SATA kabel od ARGB kontrolera koji se nalazi iza na kućišta i preko tipke kod I/O portova kontrolira osvjetljenje. Što se tiče same brzine ventilatora, prednja tri imaju DC 3-pin spojena na splitter i to se donekle da regulirati u BIOS-u, dok stražnji ima 4-pin PWM sa splitterom. Čudno, ali tak je kak je. I još jednom, hvala na podršci. ;)
Hello! I loved the video and I am taking it into account to be able to buy this cabinet, for its price it seems incredible and since it is my first high-end cabinet I wanted to know if the included fans make a lot of noise, or if the speed of the fans is adjustable fans and rgb via asus software, I mainly wanted to change the case of my Sate 1401K because its integrated fans are very noisy between 60db and it's very annoying. I hope you read my comment and you can answer me, thank you very much and I really liked the video
Hi, the case will be epic for sure and the fans are definitely ok without a doubt. They run fixeed on 1000RPMs if I remember correctly. RGB can be adjusted though. You have to connect SATA power and 5V 3-pin ARGB header to the motherboard.
One more thing because I just checked once again. The front fans are 3-pin DC connected to the same DC splitter. The rear fans is 4-pin PWM that has a splitter on it additionally.
Normally the 3 in the front are plugged into a splitter cable and u plug it into a fan connector somewhere on the front of the board, and the back fan is plugged into a rear fan connector.
Just did a build with this exact case and I was really impressed with it. Plenty of room. All the features made it very easy to add components. RGB controller built in. Excellent airflow. Three argb fans included. Cable management was good and it has a GPU brace built in. 3.5 drive case slides in and out with a click and single easy access case screw. The case and RGBs look really nice to. My only gripe was two of the panel screws where not threaded right and hard to screw in and out..Got this case at micro center in Indianapolis for 78 dollars on sale. For the price I give this case five stars.
So many nice features. Too heavy for me. But kudos to Cougar for a good design. And at a reasonable price too.
Well it's up to personal preference when it comes to weight. I never take it into consideration to be honest. But the weight comes because there is a thicker steel which most cases in this price range category don't have. Anyways, thanks for the comment as always. :)
Oh, Cougar you were doing so well! Then I saw the separate front panel connectors. It's 2023 and the front panel layout is standardized. Why not have the single unified front panel connector?
So many have them separated but I do agree on that. Not only on Cougar cases, but in general.
BRAVO DARIO ❗Super kučište za tu cijenu. Ali što uraditi s 3-pin 5V Addressable RGB , kada MBO ima 4-pin utor ❓ Što je s kontrolom brzine okretaja ventilatora ❓ KANAL ti je već poduže pravo osvježenje u moru sličnih. Samo tako dalje 🤩
Hvala puno na ovom komentaru!!!! :) Svakako mi puno znači! Ako netko nema 3-pin 5V ARGB konektor na matičnoj, onda spoji fino SATA kabel od ARGB kontrolera koji se nalazi iza na kućišta i preko tipke kod I/O portova kontrolira osvjetljenje. Što se tiče same brzine ventilatora, prednja tri imaju DC 3-pin spojena na splitter i to se donekle da regulirati u BIOS-u, dok stražnji ima 4-pin PWM sa splitterom. Čudno, ali tak je kak je. I još jednom, hvala na podršci. ;)
hello. An orange USB 3.0 port doesn't work for me. Do the two front orange ones work for you?
yes, I decided to buy that case instead corsair 4000D
SWEET!!!!! :)
Hello! I loved the video and I am taking it into account to be able to buy this cabinet, for its price it seems incredible and since it is my first high-end cabinet I wanted to know if the included fans make a lot of noise, or if the speed of the fans is adjustable fans and rgb via asus software, I mainly wanted to change the case of my Sate 1401K because its integrated fans are very noisy between 60db and it's very annoying. I hope you read my comment and you can answer me, thank you very much and I really liked the video
Hi, the case will be epic for sure and the fans are definitely ok without a doubt. They run fixeed on 1000RPMs if I remember correctly. RGB can be adjusted though. You have to connect SATA power and 5V 3-pin ARGB header to the motherboard.
One more thing because I just checked once again. The front fans are 3-pin DC connected to the same DC splitter. The rear fans is 4-pin PWM that has a splitter on it additionally.
cool case man
Hi, what amperage are these fans? Is it safe to cram all of them on a single fan header using the provided cable?
Normally the 3 in the front are plugged into a splitter cable and u plug it into a fan connector somewhere on the front of the board, and the back fan is plugged into a rear fan connector.
Does the bracket come with the case?
I can't put the front dust filter back on AAAAAH