HYUNDAI KIA SYSTEM LEAN CODES P2187 AND P2189

Поделиться
HTML-код
  • Опубликовано: 29 окт 2015
  • showing what seems to be a common issue for the hyundai or kia 2.7l engine with system lean at idle codes..also a system rich code that i believe could be linked to the failure.
  • Авто/МотоАвто/Мото

Комментарии • 75

  • @R4MON
    @R4MON 7 лет назад +3

    This was exactly what was wrong with my car. Followed your instructions (had to go pick up a pair of long needle-nose pliers at Harbor Freight) and the numbers behaved exactly the same way. Thanks for saving me a lot of money. Subscribed!

  • @jesusmalagon4336
    @jesusmalagon4336 8 лет назад +3

    Thanks James Danner another great video thanks for shering for your time thanks

  • @30kendel
    @30kendel 8 лет назад +1

    "Queue the compressor" hahaha. Fav part of the video. Awesome video! 😄

  • @johnwrench4speed
    @johnwrench4speed 8 лет назад +5

    Nice video. "Purge" is normally closed and "vent" is normally open. Therefore, when purge sticks open, vacuum leak because vent is open. Rich condition will develop at start-up (build up of fuel vapors) converts to lean condition as engine runs (drawing only atmosphere).

    • @jamesdanner7850
      @jamesdanner7850  8 лет назад

      Yea. In hindsight I should have looked to see if freeze frame data showed the rich conditions at colder engine temps. Good thinking...thanks

    • @BigMac2222
      @BigMac2222 8 лет назад +1

      +johnwrench4speed Vent is only open during key off though, it closes during key on or run. The lean condition came from a bypass valve built in to the gas cap opening when the vacuum in the tank gets too strong.

    • @johnwrench4speed
      @johnwrench4speed 8 лет назад +1

      +Derrick Hodges The vent, or as Hyundai describes it Canister Close Valve (CCV), and as described in ALLDATA:
      "The Canister Close Valve (CCV) is located between canister and fuel tank air filter. It closes off the air inlet to the canister for the Evaporative Emissions System leak detection inspection function and also prevents fuel vapors from escaping from the Canister when the vehicle is not operating."
      Therefore, in order for fuel to be drawn from the fuel tank during engine operation, the vent has to be open.

    • @BigMac2222
      @BigMac2222 8 лет назад +1

      johnwrench4speed Looks like basic CVV operation. However, an open vent is not the only means for air to enter a tank. Nearly all vehicles that still use gas caps have a vacuum bypass valve built in to keep the tank from imploding under too high vacuum scenarios. If that bypass valve is stuck open air will enter the tank even with a perfectly functioning vent/purge system.

    • @billycutshaw8538
      @billycutshaw8538 7 лет назад

      This lean run will throw a bad o2 after the repair of the purge .purge ohm was a bad one .fixed it but now its got a o2 bank 2 code.109 bucks ..hoping this keeps it off.

  • @stuzman52
    @stuzman52 8 лет назад +1

    Nice work on finding the issue. Keep up the good work!

  • @MotoFloyRepuestos
    @MotoFloyRepuestos 5 лет назад

    aqui en mi taller en Caracas, Venezuela tengo una Santa Fe con DTC p2189 y p0341, gracias por tu tiempo y conocimientos amigo

  • @EXOVCDS
    @EXOVCDS 8 лет назад +2

    Good video... I pinch hoses as well when the smoke doesn't come out anywhere and I've got the same needle nose pliers, love them!

    • @jamesdanner7850
      @jamesdanner7850  8 лет назад +1

      Nice. Back when I got them,snap on called them the stork pliers. They came with a monstrous orange coffee mug. Way back

  • @wa6gxq
    @wa6gxq 8 лет назад +1

    Learn something every video!
    Thanks!

  • @grizley6666
    @grizley6666 8 лет назад +1

    Great video. Thank-you

  • @wysetech2000
    @wysetech2000 8 лет назад +3

    Nice job as usual, James. I have seen a lot of purge solenoid problems with Hyundai cars. Usually hard start and poor run after filling the fuel tank. Sometimes I think those cars are completely built with Dorman parts. {:-)

    • @jamesdanner7850
      @jamesdanner7850  8 лет назад +1

      So what u r saying is I used OE parts. :/

    • @wysetech2000
      @wysetech2000 8 лет назад +1

      +James Danner Very good possibility.

  • @stechmer1
    @stechmer1 6 лет назад +2

    So basically if it has vacuum after it's done purging, its bad?

  • @rrmech11
    @rrmech11 8 лет назад +2

    Hello James. I just joined iATN and want to know where on iATN did you find the repair for these lean

  • @derekgray1633
    @derekgray1633 4 года назад

    Very helpful man 10/10

  • @dvdalvarez9524
    @dvdalvarez9524 5 лет назад +1

    hello i have the same probleme... my hyundai santa fe 2008... is the purge valve the probleme.. but is the same place in santa fe 2009? ( after gaz the car not starting the same code p2187 p2189

  • @mlb0611
    @mlb0611 8 лет назад +3

    fixed many kia's and Hyundai 's with the same codes, some do have issues with the canister coming apart and clogging the purge valve. I have had several 4 cyl. that would stall in the am running very rich from an over saturated canister too.

    • @jamesdanner7850
      @jamesdanner7850  8 лет назад +2

      Ok. That's good to know. One of the complaints on this car was running poorly and stalling but I never experienced it in the shop. Seems like the rich issue is happening cold or long soak time

  • @alexcuba04
    @alexcuba04 4 года назад

    So what it produce the code p 2187 and 2189 is the purge valve them system too lean them

  • @noreenmcneela1
    @noreenmcneela1 5 лет назад

    Had same codes. Purge value was clicking. Replaced valve and now 6 months later same codes but dont hear the clicking. Any ideas? Only tool I have is code scanner. Just asking before I take to shop I cant afford. Thanks

  • @eddiemartinez265
    @eddiemartinez265 8 лет назад +2

    hey jim you working like mad on time for us anymore?

  • @Stl71
    @Stl71 Год назад

    9:32 I have the same noise and same code 2187 on my Mazda 3 2005. Do you know if Kia and Mazda share the same parts? I am impressed that two different cars may have the same problems.

  • @rrmech11
    @rrmech11 8 лет назад +1

    Also try out Identix direct hit. Its iATN sister company. You can try it for free for two months. It's pretty good.

  • @abdulkreemalsultan134
    @abdulkreemalsultan134 3 года назад

    I bought new valve but still not fix the problem. B2 oxygen sensor valve is not moving even when I increase the RPM. Please advise

  • @shotoalves9041
    @shotoalves9041 4 года назад

    muito bom parabens !!!!!

  • @johnmckamy6398
    @johnmckamy6398 8 лет назад +1

    I didn't realize there were different categories of lien .

  • @WAGNER4708
    @WAGNER4708 2 года назад

    My holy faith is 2008, I turned it off and it didn't turn on anymore, I changed the fuel pump it started working but it stopped again, but after 30km it stopped and it didn't work anymore the code p2187, bank 1 appeared. Can you help me? I'm from

  • @josephtaylor6457
    @josephtaylor6457 9 месяцев назад

    I have a kia Rio 2015 and mash for gas after while I driving it is take a while to come

  • @SteveRobReviews
    @SteveRobReviews 8 лет назад +3

    Fantastic vid Danner 👍👍

  • @rrmech11
    @rrmech11 8 лет назад +1

    I always wait for your videos. Great job. Was wondering if you ever use Identifix Direct Hit? They own Iatn. Regardless, You would of found the problem. Tell all the guys hello.

  • @ScannerDanner
    @ScannerDanner 8 лет назад +8

    Im 30 seconds in and dizzy already

    • @jamesdanner7850
      @jamesdanner7850  8 лет назад +2

      I'll never be as cool as u. :p

    • @SchrodingersBox
      @SchrodingersBox 8 лет назад +2

      I love the irony when the camera pans right past a set-up tripod lol.

    • @jamesdanner7850
      @jamesdanner7850  8 лет назад +1

      I knew you would appreciate that.

    • @rrmech11
      @rrmech11 8 лет назад +1

      Schrodingers Box hey Matt signing up for the new channel.

    • @SchrodingersBox
      @SchrodingersBox 8 лет назад +1

      ***** You'll love it!! Lots of new videos there!!

  • @eddiemartinez265
    @eddiemartinez265 8 лет назад +1

    See paul made you a star now you forgot us little people?

  • @eddiemartinez265
    @eddiemartinez265 8 лет назад +1

    hey jim you must be working hard no videos.

  • @GRowe1978
    @GRowe1978 8 лет назад +1

    Oh man! A sideways check engine light? How do you fix THAT! LOL

    • @jamesdanner7850
      @jamesdanner7850  8 лет назад +1

      Duct tape. Ha

    • @GRowe1978
      @GRowe1978 8 лет назад +1

      James Danner Haha! That should do it, but if that doesn't hold you can always go with the JBweld.

  • @dblr616
    @dblr616 8 лет назад +1

    We use tracs at my shop

  • @brakedd
    @brakedd 8 лет назад +1

    worst oil fill location ever in those 2.7 SUVs

  • @shawnlockard2370
    @shawnlockard2370 8 лет назад

    Why not clear the codes?

    • @jamesdanner7850
      @jamesdanner7850  8 лет назад +2

      The way pa emissions is set up, check engine light has to be off and all readiness monitors ready or complete. (all but one) to pass. If I cleared the codes ,the monitors go not ready or incomplete . The result of a test after that is "NOT READY FOR TESTING" I needed to issue a sticker that day so my option is to issue a waiver sticker. That's qualified by spending more than $150 towards the cause of failure. But I need an initial test fail and an after repairs test fail ,where I enter the repair data. A not ready test won't let me enter data ,so I can't get waiver approval from state . I usually clear the codes after the waiver is approved

    • @shawnlockard2370
      @shawnlockard2370 8 лет назад +1

      Thanks, awesome videos. It has help me a lot

  • @wdwh4708
    @wdwh4708 5 лет назад

    good night

  • @romeondzoula229
    @romeondzoula229 3 года назад

    Besoin d'une vidéo en francais

  • @SilentServiceCode
    @SilentServiceCode 8 лет назад +1

    it's a shame the car stuff has to be mired in weird god stuff

    • @jamesdanner7850
      @jamesdanner7850  8 лет назад +2

      +SilentServiceCode I don't think it's mired. I just like to give thanks for the gift God has given me. I only put it at the end of a hopefully substantive video for that purpose . Maybe spark a thought in someone. Not preaching. Thanks for watching and the feedback

    • @davidscharringhausen8949
      @davidscharringhausen8949 7 лет назад +1

      This is not weird There is not enough information her to explain what is needed to believe.We all have sinned and come short of the glory of god. This does not mean we are horrible nasty people, just not as perfect aa God. We have not kept all of God's law.. God sent Jesus to do for us what we can not do for ourselves, pay for sin. He lived totally sin free, allowed men to do all the horrible things to him that the did, hang him on a cross to. He was buried, and third day rose from the dead, Proving he did not lie. It is finished. For God so loved you that He gave his only begotten Son , that when you believe in him, you shall not perish, but have everlasting life. The gift is your's believe it.

  • @wdwh4708
    @wdwh4708 5 лет назад

    o2senser chat ktalest