Fixed! Bosch Dishwasher Cycle Not Completing
HTML-код
- Опубликовано: 13 сен 2024
- In this video I show you how I repaired my Bosch Ascenta dishwasher. The unit would often stop mid-cycle until we would open the door and close it again. Other times it would appear to have only one minute left and then just keep running. Both issues seemrd to be caused by the same problem.
To repair, I replaced the door latch and bracket. I also replaced the door seal.
Bosch dishwasher model number SHE3AR76UC/07.
Door lock assembly: Part Number 10006917 (replaces 00636708, 00630628, 00629580, 00644989, 00623848, 00627946, 00652509, 623848, 627946, 644989, 652509).
Bracket: Part Number 00678930 (replaces 2000391, 678930, AH3482844, EA3482844, PS3482844, PS8734006).
Door Seal: Part Number 00645141 (replaces 1560744, 645141, AH3479727, EA3479727, PS3479727, PS8730289).
Please remember to subscribe! Thank you
Bingo. My Bosch stopped in the middle of wash and blinked time remaining 1:37 / It was the door, sensor latch. I pushed the door shut and gave it a little nudged to make sure sensor made contact while keeping little pressure on door. Washer resumed and I restarted whole cycle. Thank you so much. I just made you one of my favorite.
Thanks, super helpful! Was having the same issue and with your help it's fixed! One addition that my repair required was a shim added to the top center (above the door latch) to help press it down. I found another video referencing the need for a shim and that helped get the job done.
Thanks to this video I see how unlock the 00636708 lock activated for error with the door open. No other indication on Internet. Thanks a lot!
Thank you! you are genius! I thought it was something wrong with programming, but decided to take a chance on $35 part and ordered new lock. It solved the problem. Thank again.
THANK YOU!! I couldn't find any information on how to get the latch into the open position after it was knocked closed!
Great help. Nothing in the manual
Here IS The ACTUAL REASON and LASTING FIX: The problem is that there is a clog or partial obstruction "somewhere" . The issue is finding the clog. (Wait you say...I cleaned out the filter, pump cover, pump impeller...etc. then I cleaned out the drain hose ...100% checked and no clog). Maybe...Well....so did I. I shop vacuumed hose and sump and it and blew it out with a compressor...Dishwasher and Drain hose verified...Clean as a whistle. But..I experienced all the trouble and inconsistent pumping/Washing/Pumping?"Clean" Light behavior that others did. Cleaning out the filter and then resetting by shutting off the breaker for a few minutes usually works. Also the work around like this RUclips may work many times (Thanks Morgan). But eventually this is not working. My filter was clean from a few weeks back.... so when it showed up again I was perplexed. Also, The clog can be partial and just causing some back pressure to trigger the stop and clean light. Then you think all is clean....AND my sink runs good so the drain & trap must be clear...right? . Here is the more nefarious issue that is similar to people with disposal units. I pulled the hose off of the Y again...That Y joint is the last point in the path that was untested...I gently put a screwdriver in there and felt a little resistance...then pushed a little harder and POP.... a little clog in the Y adapter fell down into the trap! Voila!. I have a low Y connector where the hose connects just above the trap. The clog can get pushed out a bit and with a little siphoning or the trap backing up a bit that crud can get pushed or sucked back into the Y.... causing the problem to seem fixed and then come back. Even though the hose itself is not clogged (Ensuring a high loop on the drain hose ...or installing and Air Gap mechanism...helps this issue a bit). The point is that when the pump keeps cycling on and off and water is sitting in the bottom with and early stop ...and the "clean" light on....the path to and from the pump is blocked or partially blocked. Go from one end to the next and make 100% sure it is ALL clear. If the pump has back pressure or a clog it will tray a few times and then trigger a stop and clean light!. That is it.
Thanks, I first closed the door by pushing really hard up where lock is located and that did it. Will spray the lock with food grade lubricant. Saved me $175.00, thanks for the great info. Best
Thank you, this fixed the issue on my unit!!
Thank you very good job of explaining things
Same problem, I Have an older model Bosch #SHE3ARSXUC. I changed the inlet valve with a OEM part "40$". I found by vacuuming the drain area below filter basket and drain hose it started working all the lines have been disconnected and cleaned out. ( Still defaults to clean) ..I am going to change the float switch next and see what happens. Perhaps this is the issue? Perhaps there is a weak signal telling the inlet valve to open and start the filling process? a faulty float switch? .. I'm baffled why it works after the drain line is completely cleared but unfortunately I can't figure out what the root cause is. I can fix most things and I will not give up. My Wife is starting to look at new dishwashers at 1000,$ so therefore I'm under a lot of pressure to get this problem solved🤣🤑
Thanks for this. Also glad Bosch is making modular parts. Is this covered under warranty?
Hello there! Great video! Quick question: where did you go to get/order the parts you needed to repair the dishwasher?
Thanks!
Did you get a reply? Please post if so.
Amazon. Search for : "Bosch ######"
Where did you order the part from?
Also, where did you find the model number on the dishwasher?
Open door and look on the right side of the door. Should have a label with serial #, model # all that good stuff
Great
Where did you order the part, part number. ..?
All of the part numbers I used are in the video description text. You may have to scroll down and hit the down arrow to expand. Thanks!
Amazon. Search for : "Bosch ######"
My Bosch is broken. Again. German engineering. Man modern appliances suck
Agree. What is the root cause of this? Engineering lasting business instead of last products is a thing.