I want one of these machines so bad, I would legit start a business doing this for other people just as an excuse to give the wife as to a reason to purchase one. Cause truth is I just wanna listen to that sound and laser etch everything. So uh, will this give me a sick ass customized brand too? Lmao
yes ..it can do in seconds .. speed is too fast in 50w .. .we made a comparision video of 30w and 50w .. have a look .. .ruclips.net/video/kIxYWL3VsfI/видео.html
Can A 40 watt co2 laser cut the cerakote on an ar lower and leave an image like the one in this video? I know they cant cut deep into steel or aluminium but can they just burn off fire arm coatings and leave behind an image ?
40W CO2 can do the same thing. No need for a fiber laser; you're just burning the anodization layer off. Even the little diode lasers around 20W (optically 5.5w) should be able to do it. If you want to deep etch, you'd paint the section you want etched, lase the paint off and then use a chemical etch.
@BOYT PLANET 2.0 Hey buddy check this guys out. ruclips.net/video/0q7ykHRjm40/видео.html He has ALOT on both fiber and CO2 and explains each in great detail
I want to do an extravagant design on an upper an lower that has a similar look to gold damascene. You could even leave the pins in and have the laser engrave the ends of the pins.
Questions if you’ve a moment. I want to make ammo with custom head stamp. Would it be feasible to take something like a loading block and use a fiber laser to do the custom marking ?
If you don't mind, what brand of laser are you using and where did you purchase it from? I have been trying to purchase a laser engraver but the prices are all over the board.
Generic 30w fiber laser. Split system. Mine has the Maxphonics fiber source. China imports are cheaper than anything from US vendor but you get zero support from China. Usually between 4k to 5k but you also have to look at accessories that come with it. Some come with the rotary attachment and are higher pice. Got mine on ebay
Is this a plain fiber laser, or a MOPA fiber laser? I am considering moving from CO2 to a fiber laser because I would like to do deep metal engraving in brass and steel. Can you simply keep doing more passes to get a deeper mark? Do you have any advice?
IPG-YLP from china Ebay. I can change the power and frequency. I can not change the wave form. I don't see the one I bought anymore. Yes you can do deep engraving with more passes. Also the program uses different hatch patterns to keep the bottom smooth. See the link for marking settings. If you buy one from china support is going to suck and it has to come in through customs. www.permanentmarking.com/wp-content/uploads/TYKMA-Laser-Marking-Manual-REV214.pdf
Is that part hardcoat anodized? I'm trying to find info on a fiber laser to mark hardcoat anodized aluminum. I'm hoping a 30w laser will be enough. Thank you for posting the video, and for any further information you provide.
@@ajimachining2537 Thank you for replying. I tested a 50w fiber laser in Florida which was essentially a rebranded china laser--even had the same EZCad software. I was hoping to get by with a 30w. Definitely a huge price jump to 50w.
I hate to bother you, but you are the only person I have found to have purchased one of these. Will the 30w engrave a stainless steel pistol? Did you buy it on ebay or directly from china? Any advice would be great. Thanks
from the software and his reply, this machine is bought from China, what ever from ebay or directly from China are same, and on Amazon also has chinese supplier, they are everywhere for selling this machine, you just need to search the keyword: laser marking machine or fiber laser engraver, then you will find many machine and many different price, mostly for 30w laser the price would be around $4500 ~ $5500 with chinese best laser source Raycus.
@@smartpers0n Hello, Mopa is kind of laser, not laser brand, Raycus is a laser brand, you can see mopa laser as a upgraded fiber laser, if you need laser we have.
Sorry for tweaking your OCD. CRAP, it is facing the wrong way. That is my presonal lower. I was excited to try out the new toy. I should have mirrored the art work. Just be glad it is not yours and you don't have to look at it every day. Dam I hope OCD is not contagious because SHIT, IT IS FRIGGIN BACKWARDS!!!
I have a 20 watt fiber and some images that are imported to ezcad have a background behind them. Using corel draw to work with images. Have you had any problems like this and if so any advice? Thanks
If you mean that the white background is also being engraved, you have to go to power by pixel, expand and check disregard below, and put like "20" in the box. That will keep it from engraving white.
Know this, if you are in the business of engraving the ,"Firearm," part of a gun, you are supposed to have a gunsmith FFL. If you stipple, repair, or install parts or any modification of what ATF calls the firearm, you can not keep it in your possession overnight. It must be returned to the customer the same day, unless you have an FFL. Said firearm would have to be logged in and out. You also must provide the means to secure it, just like a dealer or other FFL.
In the video is 1064nm wavelength laser, special for metal engraving, and this software support vector image import and output, I am engineer of this laser marking machine from China, if you need i would like to help you, and i also provide this machine for worldwide, if you are interested please send inquiry to my email max@optic-tech.cn
I'm brand new to laser engraving and just picked up a 40w CNC Fiber Laser myself. Using factory settings I can engrave any of those black laser cards for sale on Amazon fine but on any other metals - nearly nothing! What could I be doing wrong? I've looked for a depth setting in EzCad which it came with and didn't find anything, I tried all different random MhZ and power settings and still no change. I can see a very slight marking if I set it to loop 10x for instance but not much beyond that yet the manufacturer shows it cutting deep into firearm slides and such. Of course out of China I'm getting no support so just wondered if any of you experienced engravers might know what I'm doing wrong?
@@n.r.8719 Yes, I did buy the 50w (not 40w like I said above) and it's still like having a brand new Ferrari in your garage unused because you were never given driving lessons. That being said, my problem isn't everyone elses problem. If you were to buy a machine and give it the much needed attention it requires in training, you could probably have a business setup and running in laser engraving within a month. I personally only get maybe an hour a week to play with it I'm so busy running a ring manufacturing company and only bought it for engraving my rings on a rotary dial so I haven't put it up there on my major to do list even though it would generate an additional 2k monthly for me in income because I'm a small business and work 14 hours a day, 7 days a week and just having a very hard time finding the time to learn. With that, let me get to the point of what I've learned. 1. Yes, it takes a lot of dedicated time and training and there are almost no training facilities anywhere in the United States online or in person for some reason. This is a trade you almost need to be grandfathered into by someone you know otherwise it's all learning by hard knocks and a lot of online research for bits and pieces. 2. I did find one company in Mission Viejo, CA but it costs me $1,500/day in training. This is apparently what the going rate is if you want to learn. 3. You are going to have to learn and master far more than just EZCad2 which from what I can see all laser engravers come stock with. You will need to learn and master Corel Draw, Adobe, and a number of other software programs particularly if you want to get into 3D and custom engravings. My best source for training.... Right here on RUclips, section by section, bit by bit and you practice what you learn as you go. That is the best information I can give you thus far and like when I was first told it would be all learning by "hard knocks self teaching", they weren't lieing. One note is that advertised on TV was a brand new desktop laser engraver that may not be nearly as high end as one like I have but it was only around $3500 for the beginner setup, looked a lot like a scanning machine and apparently they advertise everything is push a button and go so when you consider you'll probably pay more in software and training than the machine itself (I'm in it for around $8k at this point) and that isn't including the time you put into it, that's a bargain. Hopefully this helps a little and for what it's worth, here's the machine I saw on TV that looks honestly, pretty sweet! glowforge.com/?Search-Laser_Cutter-Exact-Hear-GP&msclkid=371c8db0f7231400adb3ecaed2bca301
@@PatriotCoinRings Thanks alot for sharing your dilemma. I have been researching fiber lasers for marking firearms. Even that has been difficult. Thankfully youTubers are a helpful bunch and you can generally find somebody who has made a vid of something you are trying to learn yourself. Just from what I’ve seen so far I have definitely determined there is a steep learning curve with laser engraving. I’m a fairly technical guy and am self taught at a lot of things but this looks a little daunting. Thanks again for your story. I’m still on the fence.
@@shawn5170 Right there with you Shawn. I've come a long way since I last posted that question and getting better but you're not kidding about a pretty big learning curve and if it wasn't for youtubers posting like this gentleman here, I'd be up shits creek.
I don't know. You would have to look at the specs. Also there are allot of variables. Your cost for electric, power setting each different job ect.. ect.... ect...
Im looking at starting a small business engraving gun parts like yourself and selling at gun shows but cant decide if I should purchase a co2 or fiber laser first. Any advice you could give and your opinion on which would be better to purchase first. I cant find much help online and any information you could give would be greatly appreciated sir.
This was filmed in real time. I went over it 3 times to make it deeper. The time depends on what fill pattern I use and how deep I want to go. Still learning every day!
There is no branding on it. It is a generic fiber laser from china, but the laser source inside the control box is identified as Maxphonics. If you search ebay for "30watt fiber laser" you will find they are almost all identica
@@brennanhuff2498 ruclips.net/video/WxmIXMmsorc/видео.html hi,dear friend,we have fiber marking machine,please add my whatsapp:+86-13156182531, i will give you a beautiful quotation and machine's detail information
@@Reaperrr53 ruclips.net/video/WxmIXMmsorc/видео.html hi,dear friend,we have fiber marking machine,please add my whatsapp:+86-13156182531, i will give you a beautiful quotation and machine's detail information
There is no branding on it. It is a generic fiber laser from china, but the laser source inside the control box is identified as Maxphonics. If you search ebay for "30watt fiber laser" you will find they are almost all identical.
gunfunandstuff Sticker shock and competitive pricing. For example, we have a 12”x24” ULS 40w CO2 laser, it had a $14,000 price tag. The one Epilog machine that I’m drooling over is around $65,000.
they are with aluminum tube for 65 K you should have a 1 kw 4x8 laser, and not the cheapest one its all about how you can sell your stuff cutting acrylic letters and tactile letters, the 65K machine would send bankrupt the company
Only within a couple mil of the focal length. There are some machines that have a motorized z axis that can follow a contour. Mine does not have that ability.
@@ajimachining2537 That would be a nice feature, but it would likely be a huge bump in price and complicate programming beyond what most people could do.
I got also Chinese machines.. routers and co lasers.. they working fine for me.. however with same machines many folks just cant work.. there are people year long they can not start with machine they just don't get the logic of how it works.. then those going for brand lasers and struggling with bank..
@@cnccarving you are correct, if you are first time get your hands on the laser machine, and did not get good training, you will always worring to damage the laser or hurt your self.
Hi dear 🙏🌹 I am pcb circuit board electronic designer How convert fast and easy my pdf project circuit board to ( shape trace and export dxf vector for laser engraving) laser fiber pcb engraving
depending on the setting, barely anything at all to a small localized burn...skin doesn't absorb this wavelength all that much, at least not white skin.
@@ajimachining2537 Thanks brother I appreciate the reply. If you dont mind me asking what's the price of this machine. Can we meet requirements for serial numbers and do you have any advice as to a lazer engraver that will do stippling and detailed engraving? We have been looking for months but there are so many conflicting answers.
@@seanmitchell48 ruclips.net/video/WxmIXMmsorc/видео.html hi,dear friend,we have fiber marking machine,please add my whatsapp:+86-13156182531, i will give you a beautiful quotation and machine's detail information
Yes I do NFA engraving because i am an FFL. It all depends on what it is going on and if it will be re finished. I am working on a video that will explain more of the power settings. But for AR lowers 60% power 2 hatchs x10 passes at 90 and 180deg. 1 finish pass at 315deg, pass 1 and 2 at 35hz. Cleanup at 75hz
Still using the EZ Cad. The driver board and Ez Cad are married. Seams like the dongle is programmed on the board. I have not tried another software. The only Ez Cad version thet works is the one that came with the machine. And that usb stick was flagged by antivirus. Be careful with chinese supplied software.
![ARGENTINA vs. CHILE [3-0] | RESUMEN | ELIMINATORIAS SUDAMERICANAS | FECHA 7](http://i.ytimg.com/vi/De3AWmXzhuA/mqdefault.jpg)
Is that really what it sounds like? That's pretty crazy never thought the old lazer gun toys had accurate sound fx
I believe the sound changes depending on the material being engraved. It's not the laser making the sound it's the material burning quickly
Nah, just a microphone and good editing ;)
It’s the the laser making the sound, you fucking moron.
Your doom in 8-bit glory
Fiber lasers make crazy laser sounds pew pew
That sound tho i love it
Me too! Cann't even stop it. I might spend too much time in the fiber group facebook.com/groups/fiberlasers Love the sound!
When you realize Skynet is already here:
Edit: These comments confuse me... I'm just saying it sounds cool futuristic and robotic
When you realize it's JUST a laser
When you realise that there is always one dude who has a problem ☝️☝️
Funnily enough upon seeing this comment I've just bought a limited edition t800 micro processor chip XD
Sounds like my old atari 😄 very cool machine
I wanna swipe my hand through it as fast as I can
Lol same here
I've read that fiber laser doesn't burn skin. But it can actually pass right through your skin and hit the bone.
@@brilliantgamestudios holy shit
brilliantgamestudios ya never mind the passing hand through it
@@brilliantgamestudios so you’re saying I can engrave something on the back of my skull
I want one of these machines so bad, I would legit start a business doing this for other people just as an excuse to give the wife as to a reason to purchase one. Cause truth is I just wanna listen to that sound and laser etch everything. So uh, will this give me a sick ass customized brand too? Lmao
Do you know what machine this is?
I love the sounds these make, I need to get me one of those.
50w can do that in around a second unless this is like a deep setting or something
If you’re talking about a 50w CO2 no it can’t. He isn’t marking the coating, he’s actually engraving the aluminum
yes ..it can do in seconds .. speed is too fast in 50w .. .we made a comparision video of 30w and 50w .. have a look .. .ruclips.net/video/kIxYWL3VsfI/видео.html
I’m sitting over here, happy as hell with my 40 watt CO2 laser then I see this fiber laser wizardry.
LMAOOOOOO i was thinking the exact same thing, lmaooo i really was going to comment something like that lol
patprop74 where does this guy get off waving his enormous fiber laser in our faces??
Can A 40 watt co2 laser cut the cerakote on an ar lower and leave an image like the one in this video? I know they cant cut deep into steel or aluminium but can they just burn off fire arm coatings and leave behind an image ?
40W CO2 can do the same thing. No need for a fiber laser; you're just burning the anodization layer off. Even the little diode lasers around 20W (optically 5.5w) should be able to do it. If you want to deep etch, you'd paint the section you want etched, lase the paint off and then use a chemical etch.
@BOYT PLANET 2.0 Hey buddy check this guys out. ruclips.net/video/0q7ykHRjm40/видео.html He has ALOT on both fiber and CO2 and explains each in great detail
awesome video, do you mind sharing what machine you are using.
Generic Chinese fiber laser from ebay
@@ajimachining2537thanks for sharing, is this metal engraving machine? would you mind sharing the link to this machine?
I have a 30W Fiber Laser engraver, where can I find a tutorial on how to set the machine up for engraving metal, the manual was confusing ? Thanks Ken
It is all in the way you set it.
Power, hatch, and frequency
High power, multiple hatches, 35hz will deep engrave
@@ajimachining2537 35 hz or 35Khz?
@@rickyspanish3714 i just put 35 in the frequency box i dont remember if it is in khz
@@ajigamming6939 ruclips.net/video/PV7Ao85DSWc/видео.html
Are you using the supplies EZCad software or have you changed to a different setup? Thanks!
Sound like those old video games, hahhahhaha, great times!!!!
It sounds like a video game of gunshots or racecars
What is your fee to laser the lower ?
I need one of these to start my Lasik business
What software do you use?
I have one here in Brazil and the software that came with it is bad.
Fiber lasers are just insane
Do you mind sharing the pen settings that you used?
What kind of laser are you using? Also, how deep can that laser go. Like say for instance you want to engrave a revolver barrel
It’s a Fiber Laser, we use one for our engravings.
How many watt can a 30watt do or need 50
What settings are you using? I can't seem to get white marking.
I want to do an extravagant design on an upper an lower that has a similar look to gold damascene. You could even leave the pins in and have the laser engrave the ends of the pins.
Yes
What if you put your finger in the laser?
What kind of engraver is this ? I want to start engraving pistol slides and know nothing about it. What engraver do I start with ?
30 watt fiber laser
Nice work 👍👍👍
Wow thats crazy how fast it is
Questions if you’ve a moment. I want to make ammo with custom head stamp. Would it be feasible to take something like a loading block and use a fiber laser to do the custom marking ?
Yes you could do it it will take a few passes to get the depth you want
It sounds like waiting for a commodore 64 game to load
Nice work. What laser system are you using?
How is this laser holding up?
What coating is needed to keep the .metal from rusting after the laser burn
This is aluminum so it wont rust. But oil will work in steei
If you don't mind, what brand of laser are you using and where did you purchase it from?
I have been trying to purchase a laser engraver but the prices are all over the board.
Generic 30w fiber laser. Split system. Mine has the Maxphonics fiber source. China imports are cheaper than anything from US vendor but you get zero support from China.
Usually between 4k to 5k but you also have to look at accessories that come with it. Some come with the rotary attachment and are higher pice. Got mine on ebay
Is this a plain fiber laser, or a MOPA fiber laser? I am considering moving from CO2 to a fiber laser because I would like to do deep metal engraving in brass and steel. Can you simply keep doing more passes to get a deeper mark? Do you have any advice?
IPG-YLP from china Ebay.
I can change the power and frequency. I can not change the wave form.
I don't see the one I bought anymore. Yes you can do deep engraving with more passes. Also the program uses different hatch patterns to keep the bottom smooth.
See the link for marking settings.
If you buy one from china support is going to suck and it has to come in through customs.
www.permanentmarking.com/wp-content/uploads/TYKMA-Laser-Marking-Manual-REV214.pdf
Satisfaction to the max
Is that part hardcoat anodized? I'm trying to find info on a fiber laser to mark hardcoat anodized aluminum. I'm hoping a 30w laser will be enough. Thank you for posting the video, and for any further information you provide.
Yes it is.
You need a fiber laser NOT CO2.
Co2 will leech the die color out but won't do deep engraving on metal.
@@ajimachining2537 Thank you for replying. I tested a 50w fiber laser in Florida which was essentially a rebranded china laser--even had the same EZCad software. I was hoping to get by with a 30w. Definitely a huge price jump to 50w.
@@ajfreeze215 mine is 30watts.
What program do you use? Looked seamless. Could love easier
For the video?
Davinci Resolve. Free version
Power of the laser and computer?
What kind of laser engraver are you using ?
What kind of material is this? Rubber? Can it engrave on rubber like tires?
Not rubber shit dick
What were the hatch lines measurements?
I hate to bother you, but you are the only person I have found to have purchased one of these. Will the 30w engrave a stainless steel pistol? Did you buy it on ebay or directly from china? Any advice would be great.
Thanks
Welcome to send enquiry to sales1@barch-motion.com if you need laser engraving machines for deep stainless steel engraving
from the software and his reply, this machine is bought from China, what ever from ebay or directly from China are same, and on Amazon also has chinese supplier, they are everywhere for selling this machine, you just need to search the keyword: laser marking machine or fiber laser engraver, then you will find many machine and many different price, mostly for 30w laser the price would be around $4500 ~ $5500 with chinese best laser source Raycus.
Max OPTIC LASER is raycus better than MOPA?
@@smartpers0n Hello, Mopa is kind of laser, not laser brand, Raycus is a laser brand, you can see mopa laser as a upgraded fiber laser, if you need laser we have.
@@smartpers0n ruclips.net/video/PV7Ao85DSWc/видео.html
Do you have a link to the laser your using? Or any details?
I have a 50 watt.. mind sharing your settings?
my OCD is fuckin geekin since the skull is facing the wrong way!!!
Sorry for tweaking your OCD.
CRAP, it is facing the wrong way. That is my presonal lower. I was excited to try out the new toy. I should have mirrored the art work.
Just be glad it is not yours and you don't have to look at it every day.
Dam I hope OCD is not contagious because SHIT, IT IS FRIGGIN BACKWARDS!!!
I have a 20 watt fiber and some images that are imported to ezcad have a background behind them. Using corel draw to work with images. Have you had any problems like this and if so any advice? Thanks
If you mean that the white background is also being engraved, you have to go to power by pixel, expand and check disregard below, and put like "20" in the box. That will keep it from engraving white.
amdni4 thank
@@amdni4276 Thanks lol just learned something that has anoyed me greatly !
@@amdni4276 ruclips.net/video/qY3VXxzIjOY/видео.html
@@phantienhung93 ruclips.net/video/qY3VXxzIjOY/видео.html
Know this, if you are in the business of engraving the ,"Firearm," part of a gun, you are supposed to have a gunsmith FFL. If you stipple, repair, or install parts or any modification of what ATF calls the firearm, you can not keep it in your possession overnight. It must be returned to the customer the same day, unless you have an FFL. Said firearm would have to be logged in and out. You also must provide the means to secure it, just like a dealer or other FFL.
Please provide a link for machine.
contact for quotation offer whatsApp:+86 13510567251
Can I have a link to this specific machine ? Is it still holding up well?
In the video is 1064nm wavelength laser, special for metal engraving, and this software support vector image import and output, I am engineer of this laser marking machine from China, if you need i would like to help you, and i also provide this machine for worldwide, if you are interested please send inquiry to my email max@optic-tech.cn
Max OPTIC LASER Nice
@@phantienhung93 Thanks :)
@@jycjewelrymakingmachine2886 how much for this laser machine?
brandenleecook i sell Chinese laser price $3200
What would happen if you used it on your arm, like a tattoo machine ? 🤔
Nothing. Look up the guy that did Still Alive and Want You Gone on a fiber laser.
Sounds like DBZ androids / cell game era
How much was your machine?
How much was your machine
how much workspace lens?
what kind of laser is this?????????
30 watt Fiber laser from China. Ebay..
what machines are u using
30 watt fiber laser from china. Ebay
I'm brand new to laser engraving and just picked up a 40w CNC Fiber Laser myself. Using factory settings I can engrave any of those black laser cards for sale on Amazon fine but on any other metals - nearly nothing! What could I be doing wrong? I've looked for a depth setting in EzCad which it came with and didn't find anything, I tried all different random MhZ and power settings and still no change. I can see a very slight marking if I set it to loop 10x for instance but not much beyond that yet the manufacturer shows it cutting deep into firearm slides and such. Of course out of China I'm getting no support so just wondered if any of you experienced engravers might know what I'm doing wrong?
I can point you to this facebook fiber laser group where you can find a lot of helpful info: facebook.com/groups/4105345129538639/
How did that turn out? In looking to purchase a machine here soon... Any advice you can share?
@@n.r.8719 Yes, I did buy the 50w (not 40w like I said above) and it's still like having a brand new Ferrari in your garage unused because you were never given driving lessons. That being said, my problem isn't everyone elses problem. If you were to buy a machine and give it the much needed attention it requires in training, you could probably have a business setup and running in laser engraving within a month. I personally only get maybe an hour a week to play with it I'm so busy running a ring manufacturing company and only bought it for engraving my rings on a rotary dial so I haven't put it up there on my major to do list even though it would generate an additional 2k monthly for me in income because I'm a small business and work 14 hours a day, 7 days a week and just having a very hard time finding the time to learn. With that, let me get to the point of what I've learned.
1. Yes, it takes a lot of dedicated time and training and there are almost no training facilities anywhere in the United States online or in person for some reason. This is a trade you almost need to be grandfathered into by someone you know otherwise it's all learning by hard knocks and a lot of online research for bits and pieces.
2. I did find one company in Mission Viejo, CA but it costs me $1,500/day in training. This is apparently what the going rate is if you want to learn.
3. You are going to have to learn and master far more than just EZCad2 which from what I can see all laser engravers come stock with. You will need to learn and master Corel Draw, Adobe, and a number of other software programs particularly if you want to get into 3D and custom engravings.
My best source for training.... Right here on RUclips, section by section, bit by bit and you practice what you learn as you go.
That is the best information I can give you thus far and like when I was first told it would be all learning by "hard knocks self teaching", they weren't lieing.
One note is that advertised on TV was a brand new desktop laser engraver that may not be nearly as high end as one like I have but it was only around $3500 for the beginner setup, looked a lot like a scanning machine and apparently they advertise everything is push a button and go so when you consider you'll probably pay more in software and training than the machine itself (I'm in it for around $8k at this point) and that isn't including the time you put into it, that's a bargain. Hopefully this helps a little and for what it's worth, here's the machine I saw on TV that looks honestly, pretty sweet!
glowforge.com/?Search-Laser_Cutter-Exact-Hear-GP&msclkid=371c8db0f7231400adb3ecaed2bca301
@@PatriotCoinRings Thanks alot for sharing your dilemma. I have been researching fiber lasers for marking firearms. Even that has been difficult. Thankfully youTubers are a helpful bunch and you can generally find somebody who has made a vid of something you are trying to learn yourself. Just from what I’ve seen so far I have definitely determined there is a steep learning curve with laser engraving. I’m a fairly technical guy and am self taught at a lot of things but this looks a little daunting. Thanks again for your story. I’m still on the fence.
@@shawn5170 Right there with you Shawn. I've come a long way since I last posted that question and getting better but you're not kidding about a pretty big learning curve and if it wasn't for youtubers posting like this gentleman here, I'd be up shits creek.
When your sibling farted first then you feel like farting and its payback time.🌚
The sound:
What is the cost to operate per hour on this machine?
I don't know. You would have to look at the specs. Also there are allot of variables. Your cost for electric, power setting each different job ect.. ect.... ect...
Settings please
Im looking at starting a small business engraving gun parts like yourself and selling at gun shows but cant decide if I should purchase a co2 or fiber laser first. Any advice you could give and your opinion on which would be better to purchase first. I cant find much help online and any information you could give would be greatly appreciated sir.
Fiber laser is what you need for engraving on gun metal. CO2 is better suited for non metal parts
fiber is the best bang for your buck.
hmm
you can get a nice fiber laser on Ebay shipped from USA California 30w system for $5500 only.. I got one and I love every single day
@@hemidesign omg, 30w laser only at $5500
That thing is fucking horrifying
What lazer setup are you using?
30watt fiber laser. With galvo head
Can you do this to any AR Lower? If so, does it have to be gutted ?
ruclips.net/video/qY3VXxzIjOY/видео.html
Yes, and no it does not need to be gutted
How long did it take to do this?
This was filmed in real time. I went over it 3 times to make it deeper. The time depends on what fill pattern I use and how deep I want to go. Still learning every day!
which brand engraver are you using? interested in purchasing one for myself
There is no branding on it. It is a generic fiber laser from china, but the laser source inside the control box is identified as Maxphonics. If you search ebay for "30watt fiber laser" you will find they are almost all identica
thanks!
@@brennanhuff2498 ruclips.net/video/WxmIXMmsorc/видео.html hi,dear friend,we have fiber marking machine,please add my whatsapp:+86-13156182531, i will give you a beautiful quotation and machine's detail information
We just bought a 30 watt was wondering if I could ask some questions
Yea email me and I will send you my cell number
Aji549@gmail.com
@@ajimachining2537 we got the laser from style cnc in China we r having a little trouble figuring out software
@@freddiedrawhorn1939 ruclips.net/video/qY3VXxzIjOY/видео.html
@@ajimachining2537 any way i can email you as well? i just got my machine and would love someone to ask some questions
I wonder when you do it on a humans back
Will it cut to the legal marking depth for serial number and firearm info?
Bobby Eaves yes
@@Reaperrr53 ruclips.net/video/PV7Ao85DSWc/видео.html
Where do I purchase this machine?
Ebay
@@ajimachining2537 Where on Ebay>?? I NEED ONE
@@Reaperrr53 search on ebay "30watt fiber laser"
@@Reaperrr53 ruclips.net/video/WxmIXMmsorc/видео.html hi,dear friend,we have fiber marking machine,please add my whatsapp:+86-13156182531, i will give you a beautiful quotation and machine's detail information
@@Reaperrr53 ruclips.net/video/qY3VXxzIjOY/видео.html
How much was your machine please?
Have you asked in these laser groups? facebook.com/groups/440091022989424/
facebook.com/groups/4105345129538639/
what's the price of this machine in Indian rupee,s ?
Hello, I want to make an engraving on a silver ring
contact for quotation offer whatsApp:+86 13510567251
ruclips.net/video/nncFaioPyOI/видео.html
can you send me that file?
about how much money per one🧐
Nice skull 👍
$30. - 40
what software ?
Ezcad2
what specific brand is your laser? @@ajimachining2537
There is no branding on it. It is a generic fiber laser from china, but the laser source inside the control box is identified as Maxphonics. If you search ebay for "30watt fiber laser" you will find they are almost all identical.
@@benchmarksignsandgifts ruclips.net/video/PV7Ao85DSWc/видео.html
I know that probably is late to ask but, can you please share with us the price and seller of this machine ? Thank you so much!
Hi Alexandru! We sell a 30W laser that has this capability. Check it out here: swistek.com/product/fiber-laser-marking-machine/
swistekswiss thank you verry mich but do please email me with a price offer for this machine also for a bigger table size alexandruchesoi@gmail.com
Why doesn't any of these companies list the prices on their machines? What are they afraid of and/or hiding?
gunfunandstuff Sticker shock and competitive pricing. For example, we have a 12”x24” ULS 40w CO2 laser, it had a $14,000 price tag. The one Epilog machine that I’m drooling over is around $65,000.
they are with aluminum tube
for 65 K you should have a 1 kw 4x8 laser, and not the cheapest one
its all about how you can sell your stuff
cutting acrylic letters and tactile letters, the 65K machine would send bankrupt the company
I legit wanna die via Laser Machine, it's gonna be painfull...
Can you engrave on uneven surfaces?
Only within a couple mil of the focal length. There are some machines that have a motorized z axis that can follow a contour. Mine does not have that ability.
@@ajimachining2537
That would be a nice feature, but it would likely be a huge bump in price and complicate programming beyond what most people could do.
@@joelanderegg2092 ruclips.net/video/qY3VXxzIjOY/видео.html
Is that a chinese fiber laser? If so, are you happy with it?
Yes, Chinese 30w fiber laser. So far no issues.
I got also Chinese machines..
routers and co lasers.. they working fine for me..
however with same machines many folks just cant work..
there are people year long they can not start with machine they just don't get the logic of how it works..
then those going for brand lasers and struggling with bank..
@@cnccarving you are correct, if you are first time get your hands on the laser machine, and did not get good training, you will always worring to damage the laser or hurt your self.
@@cnccarving ruclips.net/video/J0CgTmFDaT8/видео.html
so cool
Hi dear 🙏🌹
I am pcb circuit board electronic designer
How convert fast and easy my pdf project circuit board to ( shape trace and export dxf vector for laser engraving) laser fiber pcb engraving
sorry for the delay this comment was flagged as spam. Send me a file and I will do a video on it.
aji549@gmail.com
Edit: thank for like.
what happens if that laser hits your finger :O
Dont know and not willing to try
depending on the setting, barely anything at all to a small localized burn...skin doesn't absorb this wavelength all that much, at least not white skin.
@@AKAtheA ruclips.net/video/J0CgTmFDaT8/видео.html
What model laser is this?
30 watt fiber laser. Kind of a generic laser model. Maxphonics power source. Ebay
@@ajimachining2537 Thanks brother I appreciate the reply. If you dont mind me asking what's the price of this machine. Can we meet requirements for serial numbers and do you have any advice as to a lazer engraver that will do stippling and detailed engraving? We have been looking for months but there are so many conflicting answers.
Email me you number we can talk
aji549@gmail.com
@@seanmitchell48 ruclips.net/video/WxmIXMmsorc/видео.html hi,dear friend,we have fiber marking machine,please add my whatsapp:+86-13156182531, i will give you a beautiful quotation and machine's detail information
@@seanmitchell48 ruclips.net/video/qY3VXxzIjOY/видео.html
pew pew pew 😙👉💥
That looks great! Have you tried "deep" engraving for NFA projects and if so what are the settings, as I too have a 30 w fiber china laser
Yes I do NFA engraving because i am an FFL.
It all depends on what it is going on and if it will be re finished.
I am working on a video that will explain more of the power settings.
But for AR lowers 60% power 2 hatchs x10 passes at 90 and 180deg. 1 finish pass at 315deg, pass 1 and 2 at 35hz. Cleanup at 75hz
@@ajimachining2537 Hello sir! Great video. Looking forward to see more of your tutorials soon. China Fiber Laser owner here 😉
@@ajimachining2537 Hello sir! Great video. Looking forward to see more of your tutorials soon. China Fiber Laser owner here 😉
@@marquez_on_quest7596 ruclips.net/video/PV7Ao85DSWc/видео.html
@@marquez_on_quest7596 ruclips.net/video/qY3VXxzIjOY/видео.html
I am working this machine
ruclips.net/video/qY3VXxzIjOY/видео.html
MRP bolo sar
Hi! What is your laser maker and model?
30w fiber
@@kelbyparker9712 Thanks!
Put your arm on their
👍🇺🇸✔✔✔
Do a shitload of pain killers and get a quick tattoo.
ruclips.net/video/qY3VXxzIjOY/видео.html
Still using the EZ Cad.
The driver board and Ez Cad are married. Seams like the dongle is programmed on the board.
I have not tried another software. The only Ez Cad version thet works is the one that came with the machine. And that usb stick was flagged by antivirus. Be careful with chinese supplied software.
The coard card is only match with the EZCAD software, this software has own driver to reject fake software, that is why mismark as a virus