Stihl TS400 Wont Start Cut Off Saw Rebuild / Service - Piston Replacement [Will it RUN]
HTML-код
- Опубликовано: 10 сен 2024
- Picked up this Stihl TS400 Cut Off Saw from a garage clear, looks to have water damage. The engine is now seized, now the Stihl TS400 Wont Start. Can we take this junk Stihl TS400 cut of saw and rebuild it, with new parts and get this cut off saw working once again.
In this video we replace the piston and rings amzn.to/3a5nhvs, pull cord replacement amzn.to/323Z43Y, air filter, spark plug, belt tension, spark plug cap amzn.to/3a59XqV, clean the carb out in the ultrasonic cleaner and so on.
Instagram - / therealfixitbuilditgarage
Subscribe to the channel - / @fixitbuilditgarage
Piston & Rings Assembly Fits Stihl TS400 Cut Off Saw - amzn.to/3a5nhvs
Recoil Starter Rope Pull Handle & Cord - amzn.to/323Z43Y
Service Kit Air Fuel Filter Set Spark Plug Shroud Cap Fits Stihl - amzn.to/3a59XqV
Playlists
⚙ Will it RUN Playlist - • Will it run?
⚙ FORD Mustang 170ci Engine Build - • 1961 170ci FORD Mustan...
⚙ General How to Playlist - • How to videos
⚙ Reviews Playlist - • Reviews
⚙ MR2 Build Playlist - • Playlist
⚙ RX7 Playlist - • 1993 Japan Import RX7 FD
⚙ Mini Cooper Playlist - • Mini Cooper D F55 [201...
⚙ Range Rover Evoque Playlist - • Range Rover Evoque [20...
⚙ Marine Fish Tank Playlist - • 10ft Marine Fish Tank
Music
NCS: Music Without Limitations
NCS Spotify: spoti.fi/NCS
Free Download / Stream: ncs.io/adventure
Vibe With Me by Joakim Karud / joakimkarud
Music promoted by Audio Library • Vibe With Me - Joakim ...
#therealfixitbuilditgarage #stihl #ts400
I have 3 of these saws , none of them run. I been a drag racer all my life and have built many engines but these saws are aggravating. Thanks for the video , I'm going to use it to see if I can get at least one of these running 👍👍
This is an excellent video, very well shot and explained. Now I'm looking for ward to reassembling an old TS400 that has a badly scored piston.
*Piston & Rings Assembly Fits Stihl TS 400 Cut Off Saw* - amzn.to/2Nm1XJV
*Recoil Starter Rope Pull Handle & Cord* - amzn.to/3auNbJB
*Service Kit Air Fuel Filter Set Spark Plug Shroud Cap Fits Stihl* - amzn.to/37s2Ya6
The clutch drum is on the wrong way round..it needs the starter cup removing and clutch drum fitted the correct way round. it will bind up the way it is.
great video just about to attack a seized 400 im alot less worried after watching this!
Glad the video helped
I recommend DIESEL .
I bought a Honda 5hp engine , it had been left outside with no fuel cap on it , over the years fuel evaporates , water was in the carb and piston area ,. I took sparkplug out filled piston with red diesel over night . Next day stilsons on shaft , slightly turning did this for 5 min , re diesel piston , next day fully turning . Put a new carburator on it , drained oil , new plug , fired up 3rd pull .
Great video, thanks!
Always melt the end of the cord otherwise the knot can come undone.
I purchased this cord for this saw, I think it came with the ends melted if I recall - but very good tip 👍
Awesome!
Thank you
Great clear video but you missed to replace all the bearings and oil seals
Hello, they seemed ok at the time, wanted to get the machine running again for as cheap as possible, if it was in much better condition, would have spent more on it
thank u man great job
Fantastic job saving the unit. 👍 you got a new subscriber 😁
Awesome, thank you!
Top video keep them coming 👍👍
Thanks 👍
For anyone watching this video the crankshaft bearings were gone on this saw it wont stay going for very long
Great vid ,
But my trigger has broken , I’ve been sent a new one but don’t know how to remove the pin that holds the trigger in ,
Do you have any idea ?
🙏
Hi nice informative video , my ts400 has just stopped working the pull chord seemed jammed .
After watching your clip I’ve stripped it down and found that 1 of the piston rings had broke and scratched the piston and pot I’ve ordered new ones and waiting to fit them.
Any idea what would cause this?
Hi, thank you for the comment, could be a few things, overheating is common, poor lubrication = friction = heat. Rings are brittle, if the correct fuel/oil mix is not used, this could break rigs. Has it been sat for a few years and sized, pulling the chord may have broke the rings (had that happen before) maybe just worn down from use. You dont the correct thing in getting a new pot and piston - ensure your carb is set up correctly also, not too lean.
What cleaner solution in ultrasonic cleaner mate and how long do you have on for and temperature thanks
So im tryin to fix my ts400. filled it up and next day there was quite a bad leak any idea, cuz it wasnt touched since it was filled 😅.
Hello, guessing fuel leaked out, if it was stored on its base and leaked, i would check out fuel tank, could be cracked, if it was on its side, seal on filler cap/fuel hose maybe.
Awesome vid.. Thanks m8.. Any clearer vids on the carb tuning? Rich/lean etc.. An also.. How much is that ultrasonic cleaner? Lovin that!
They start around $100
Hello, thanks for comment, glad you enjoyed it. Not done any vids on carbs tuning, lots on RUclips, set to default settings and work from there. Think I paid around £100 for the ultrasonic cleaner, done a few videos on this cleaner - great bit of kit.
Hi hopefully you can help me out I have a ts420 it starts one time and runs really rough and when I try to start again it won't start and I checked the spark plug and it's full of fuel??
I would start with the carb, set the H and L neddles back to factory settings, add fresh fuel with correct fuel to oil mix, keep air filter off and try, if its still bogging down, i would clean out the carb and fit a new gasket kit.
What size is your ultra sonic cleaner? 6L?
Thumbs up from me, and I have hit that subscribe button! Brilliant video! Would of liked to see it real time (no times lapse) as i plan to rebuild a non running ts400 but I should be able to do it just fine following this.🙏
Fantastic job 👍
Did you get your blade? Have you used this since the rebuild? How's it preforming?
Excellent job 👍👍💪👌👊🤙💯🍺
Thanks for the support 👍 I would like to do real time videos however that would be hrs long 🤔I have got a blade to install, will be using it this spring when I get round to laying my new drive way. Think it needs a new clutch so may do a video on that. Good luck on the rebuild
@@FIXitBUILDitGARAGE thanks 👍 defo video it if you re do the clutch 👍🤙👊👌 awesome work 👍💪🍺
You can slow the speed down of utube videos... Think its top right three buttons (utube it if not? Lol) ... slows audio down obvs but can be handy...
What is the horse power on the 64cc cutting
Off machine
Needs a belt or a clutch 🤔
Hi mate. Any idea why my ts400 smokes badly when running and cuts out if you don’t rev it?
Looks to be clutch - on my list to do
Great content pal. Quick question I have a ts400 and it cuts out when not revved. Smokes really badly (white smoke) do you reckon it needs a service or is it something else? Regards
Thanks, it could be a bunch of things, carb not set correctly (idel scew or may need cleaning) and bad fuel mix comes to mind - I would add fresh fuel / oil - 1:50 and clean out the carb (set the H and L needles at the factory settings) try that for a start - could be as simple as too much oil in the fuel
@@FIXitBUILDitGARAGE thanks pal. Will give it try soon.
*update* used fresh fuel and oil, did the trick. Thanks for your help 👌🏼
Man them crank bearings are talking to you singing a loud song..!