Another great job Kevin, you must have a cast iron chest to land those gearboxes on 😂, not to mention the strength to get it back in again. Proper job well done.
My car is currently downstairs in the parking lot with the transmission underneath it if it hasn't been stolen😂😂😂 my man you are an animal putting that back up by yourself
Thank you very much my brother for the super strong mechanical video there are not many like you. really it is a very clean finished work thank you for your help and I would like to see other videos really a mechanical genius I wish you good luck my brother 👍💪
I've got a 2012 astra j 1.3 dual mass flywheel and clutch to do, it looks the same as this but states you need a tool to depress the clutch, I've got the old fashioned C clips that used to come on vauxhall clutches back in the day, i was worried I wouldn't be able to fit the clutch without this special tool but looks like you have done it without it anyway so I maybe won't need the C clips on the side of the clutch. Great video BTW
Thanks for making the videos . 2 questions what determines if you need a new flywheel and also I notice you use red rubber grease and not the grease that usually comes with the clutch kits , is the rubber grease better or doesn’t it really matter ? Thanks 👍
Just started doing mine basing it off this thanks. 😁 Just to let people know if it's the F17 transmission (5 speed manual) there's no drain plug. Spent 10 mins looking for it before consulting the trusted Haynes. The lower diff cover plate has to be taken off to drain it and apparently a new gasket installed when refitting it.
Hi, great video. I have one in bits right now, I'm struggling to find the correct torque settings for the flywheel bolts. If you could let me know that would be great thanks 👍 Edit...found it its 44nm 👍
Was that new oil you put back in Kevin or the old stuff? I assume its normal to drain on this model to prevent spillage. Great video skills by the way.
If you were on my side of the ocean I would have you do my clutch. Do you have a video of the first gen AWD Rav4 (1994 to 2000)? I did a search of your channel but did not find one. Thanks.
Great video as always, just curiosity question....all the clutches you replace, do you 'diagnose" them as bad first or does someone else? I'm just wondering if you ever shown up to replace one that actually didn't need replacement. I know here in the US, people will have someone "diagnose" a veh issue but turn around and let someone else fix it b/c they're cheaper.......
If the engine rpm increases when you floor it while the speed of the car stays the same, something is slipping in the clutch. Taking the clutch out is the only way I know of to find out whats wrong. For example the friction disc might be rusted to the transmission input shaft, and that can make the clutch slip, but the only way to fix it is to take it out.
Some Gearboxes have "diagnosis holes", where u can pull a rubber part away and watch with a endoscope / telescope camera inside... That's the complicated way... Clutch diagnosis is really simple. You can Google it. The more interesting question is, how does someone decide if it's necessary to change the flywheel or not. Flywheels are really expensive
@@montecs3087 For solid one piece flywheels I never have changed them. Sure they have heat marks and are glossy, but it makes no difference on a regular commuter car application.
@@WMCS Ratchet has a 5 year warranty. Battery 2 years for the Fuel Series... As I had a few compact head models break. But I abused them. Was no big deal as they sent me a new one next day...
Did you replace clutch in opel 1.7 CDTI about 2009 in astra, combo, ? I can't find this engine on your channel. Or can you advise if 1.3 CDTI is similar and can take it as a base ?
Afternoon Kevin The bolts you removed from the gearbox, did you use E sockets of will normal sockets still work, only asking as I have to do the shocks on my vectra and they have these type of headed bolts Cheers Phil
Watching that box just bang slightly on the floor, have u ever done a vauxhall box and the pinion in the diff drop and the shaft won't go bk in 🙈 I know I have
Not in the last 6 years. But what I have come across several times is the M32 gearbox that the internal bearing has failed and as soon as it’s tilted it falls apart from the inside. One thing I never fail to do is once gearboxes are out I go through all the gears and spin the lay shaft to check for any roughness in the bearing. Then I can explain to customer the likely outcome. All keep customers in the know then nothing comes back to you.
www.williamsmobileclutch.co.uk
Thanks for watching ..
K-A. Williams.
Another great job Kevin, you must have a cast iron chest to land those gearboxes on 😂, not to mention the strength to get it back in again. Proper job well done.
Great video by a proper professional no need for annoying music or boring chat, brilliant man, well done and bring on some more!
Thanks for the feedback.
Great job your the hardest worker why can’t everyone work like you well done keep it up bud 👍👍👍🛠🛠
My car is currently downstairs in the parking lot with the transmission underneath it if it hasn't been stolen😂😂😂 my man you are an animal putting that back up by yourself
Great job as always, it's not just me that struggle locating the gearbox back in 🤣🤣🤣
A bit like the lottery .. 🍻
Been watching your vids till all hours 😀👍👍
Thank you very much my brother for the super strong mechanical video there are not many like you. really it is a very clean finished work thank you for your help and I would like to see other videos really a mechanical genius I wish you good luck my brother 👍💪
Thanks for the feedback
there is nothing to do my friend really a finished job no headache with the apprentices all the pieces in their place not a lost screw 😂😂👍 good luck
Wow this was incredible work
I've got a 2012 astra j 1.3 dual mass flywheel and clutch to do, it looks the same as this but states you need a tool to depress the clutch, I've got the old fashioned C clips that used to come on vauxhall clutches back in the day, i was worried I wouldn't be able to fit the clutch without this special tool but looks like you have done it without it anyway so I maybe won't need the C clips on the side of the clutch. Great video BTW
A really good job, I think you have done it before, After watching the video I have decided
to have a garage do the work, We’ll done👍
Exelllent job kev
Thanks for making the videos . 2 questions what determines if you need a new flywheel and also I notice you use red rubber grease and not the grease that usually comes with the clutch kits , is the rubber grease better or doesn’t it really matter ? Thanks 👍
bonjour franchement bravo très beau travail merci beaucoup
Merci ..
Thank you sir !
Thank you i need video like this 😅
Just started doing mine basing it off this thanks. 😁 Just to let people know if it's the F17 transmission (5 speed manual) there's no drain plug. Spent 10 mins looking for it before consulting the trusted Haynes. The lower diff cover plate has to be taken off to drain it and apparently a new gasket installed when refitting it.
This is the one I need 😁
and that's a thumbs up from me kevin
Well done 👍
What a focking work.💪 ninja man
I couldn't fault him he did an excellent job. I would recommend him everytime.
Thankyou.
Well done Kevin. Version 1.3 diesel 75 or 90 hp? The m20 6-speed gearbox has the defect of noisy gearbox bearings
Hi, great video. I have one in bits right now, I'm struggling to find the correct torque settings for the flywheel bolts. If you could let me know that would be great thanks 👍
Edit...found it its 44nm 👍
Boa noite muito top esse carro novo amigo
Good jod Kevin comme dab 👏👏👏👏👏
Was that new oil you put back in Kevin or the old stuff? I assume its normal to drain on this model to prevent spillage. Great video skills by the way.
If you were on my side of the ocean I would have you do my clutch. Do you have a video of the first gen AWD Rav4 (1994 to 2000)? I did a search of your channel but did not find one. Thanks.
Forza Albert un 😘 da Palermo italy
Did you start a new channel or change your channel name
Love your work man! Can I ask what gloves you use and where do you get them from?
Which reminds me I need to buy some more. Off eBay. Orange nitrile.
@@WMCS thanks for replying. Keep up the good work
Great video as always, just curiosity question....all the clutches you replace, do you 'diagnose" them as bad first or does someone else? I'm just wondering if you ever shown up to replace one that actually didn't need replacement. I know here in the US, people will have someone "diagnose" a veh issue but turn around and let someone else fix it b/c they're cheaper.......
If the engine rpm increases when you floor it while the speed of the car stays the same, something is slipping in the clutch. Taking the clutch out is the only way I know of to find out whats wrong. For example the friction disc might be rusted to the transmission input shaft, and that can make the clutch slip, but the only way to fix it is to take it out.
Some Gearboxes have "diagnosis holes", where u can pull a rubber part away and watch with a endoscope / telescope camera inside... That's the complicated way... Clutch diagnosis is really simple. You can Google it. The more interesting question is, how does someone decide if it's necessary to change the flywheel or not. Flywheels are really expensive
@@montecs3087 For solid one piece flywheels I never have changed them. Sure they have heat marks and are glossy, but it makes no difference on a regular commuter car application.
Watched yesterday's video last night Kevin felt sorry for you when your electric ratchet packed up 🙄 have a great Sunday pal 👍
Only 3 months it lasted that expensive ratchet. A bit of a thumbs down in that one 😁🍻
@@WMCS that's rubbish mate 3 months maybe go for a snap on 1 next
@@WMCS Ratchet has a 5 year warranty. Battery 2 years for the Fuel Series...
As I had a few compact head models break. But I abused them. Was no big deal as they sent me a new one next day...
have you ever done a 1.4 citroen c2 before?
Are Corsa C 1.2 ecotec and Corsa D 1.2 ecotec clutch kit the same? 😊
Just a question, is it a M20 gearbox?
Did you replace clutch in opel 1.7 CDTI about 2009 in astra, combo, ? I can't find this engine on your channel. Or can you advise if 1.3 CDTI is similar and can take it as a base ?
your new subscribers,
Good work. Corsa c/ combo is even worse because you have that subframe at the front
Afternoon Kevin
The bolts you removed from the gearbox, did you use E sockets of will normal sockets still work, only asking as I have to do the shocks on my vectra and they have these type of headed bolts
Cheers Phil
Hi Phil. In this instance I used E sockets. But countless times a 14mm impact socket will do the job perfectly without any issues whatsoever.
muy bien muy bien muy bien
Watching that box just bang slightly on the floor, have u ever done a vauxhall box and the pinion in the diff drop and the shaft won't go bk in 🙈 I know I have
Not in the last 6 years. But what I have come across several times is the M32 gearbox that the internal bearing has failed and as soon as it’s tilted it falls apart from the inside.
One thing I never fail to do is once gearboxes are out I go through all the gears and spin the lay shaft to check for any roughness in the bearing. Then I can explain to customer the likely outcome.
All keep customers in the know then nothing comes back to you.
En España se llama Opel Corsa👍👍
😁🍻🍻
Could you do it, on easytronic 3.0
Unfortunately I don’t work on anything but manual 🍻
The universally used fiat 1.3 multijet or Vauxhall cdti and suzuki ddis. +fiat jtd.well proven and if maintenance given good 4 200k at least.
👏👏👏👏👏👏👏👍
✔️
Thank you.
j aime les videos quant tu montre en detail le demontage comme la une voiture mais en detail nickel
This is hard graft.