This channel saves me loads of time when doing cars I've never done a clutch on in my small independent garage. Things like how gear linkages come apart etc are a big help 👍
Really enjoyed this video and was amazed how much work was involved to replace the clutch what was impressive about it was you done most of the work while laying on your back which can’t be easy but you made it all look very easy so well done Kevin the clutch Ninja.
You got a good “wrench feel” - torquing the pressure plate and other bolts. I can feel those years of experience through the screen. Well done buddy, top-class your videos.
Amazing work! Thank you for sharing your knowledge with us! When your are supporting the engine, if the rubber pad slips or the jack lowers is there the danger of the engine falling down on you ? or the other mount can still hold the weight of the engine ?
Certain cars I’ve stopped doing. And A4 is one of them. I can take it on. But the in-line engine makes it a bit longer to access the side driveshaft bolts. For the right money I’ll do it tho.
A channel full of knowledge. Not a week goes by without me seeing a clutch replacement. I'm not a superman like you, so how much weight do you estimate the Corsa gearbox has? 😁
Some captions here and there would be good. I was curious about why the bell housing had grass cuttings inside it and why you greased the bolt holes. The hydraulic connector looked strange, is that something new or am I just hopelessly out of date?
If it was me i would replace a flywheel seal ring while your are in YOU did not mention that we have to set engine at Tdc mark also i suppose we schould put mark befor removing clutch plate
Me gustan tus videos, siempre que puedo me tomo el tiempo de mirarlos...te felicito haces un exelente trabajo y me inspiras a hacer lo mismo! queria preguntarte si reutilizas el aceite de la caja de cambios o le pones aceite nuevo? Saludos desde Argentina!
hi. this is a great video, very helpful!! would you be able to tell me how to remove the plastic grommit in the top of the bell housing? my slave cylinder looks different to this and the old fluid pipe does not match the new slave cylinder. old pipe is not compression fitting. wondering if someone has fitted a diesel one? please help sir.
Got the new one in tried it … it smashed a hole in the inside of the bell housing/ gear box right in line with the starter motor … the rivets in the new kit are 1mm higher than the old ones on the pressure plate . Do you think that could be the cause ?
Hi brilliant videos, youve given me the confidence to change my clutch on my sons corsa e, quick question on the corsa e theres a lower leg frame running from the rad pack that isnt on the corsa d. Can you still get the gearbox out with that there?
How long did this take you to do? I’m having to change my flywheel soon because it’s juddering everytime I’m in 1st gear setting off. Sooo just trying to see if I can do it whilst working full time 😅 mine is a 66 corsa .
![[DOKKAN BATTLE] Worldwide Campaign Announcement Video](http://i.ytimg.com/vi/zxfEiMksZQs/mqdefault.jpg)
www.williamsmobileclutch.co.uk
Thanks for visiting our channel. And for the support and feedbacks.
K-A. Williams
This channel saves me loads of time when doing cars I've never done a clutch on in my small independent garage. Things like how gear linkages come apart etc are a big help 👍
Really enjoyed this video and was amazed how much work was involved to replace the clutch what was impressive about it was you done most of the work while laying on your back which can’t be easy but you made it all look very easy so well done Kevin the clutch Ninja.
Kevin, thank you so much for the video. With this I was able to do it on the Corsa E (2017) by myself for the first time! :) Greetings from Germany!
You got a good “wrench feel” - torquing the pressure plate and other bolts. I can feel those years of experience through the screen. Well done buddy, top-class your videos.
Thanks for the feedback 🍻🍻🍻
Kevin I do enjoy watching your videos. You make everything look easy when you know what your doing .
Thanks for the feedback.. very much appreciated
Mines on 91 odd thousand original clutch and started juddering this video is well helpful and oddly satisfying
You doing great job Kevin, I learned a lot from your channel. Many thanks.
Thank you mate. Your feedback and support., very much appreciated 🍻
😁
kevin as always such a star you do work for your money one in a million
Amazing work! Thank you for sharing your knowledge with us!
When your are supporting the engine, if the rubber pad slips or the jack lowers is there the danger of the engine falling down on you ? or the other mount can still hold the weight of the engine ?
A Specialist on Work...!!! Thank You...!!!
Fantastic video Kevin thanks for sharing 👍 is it only certain cars you specialise in?
You never seem to get any A4 clutch’s which are quite popular…
Certain cars I’ve stopped doing. And A4 is one of them.
I can take it on. But the in-line engine makes it a bit longer to access the side driveshaft bolts. For the right money I’ll do it tho.
just doing mine i got stuck on gear link like you lol but sorted now thanks
Either someone’s got a lead foot or there’s been a bit traffic light Grand Prix going on, that clutch is completely fried 😂
Super strong chap, you don't need the gym that's for sure
A channel full of knowledge. Not a week goes by without me seeing a clutch replacement.
I'm not a superman like you, so how much weight do you estimate the Corsa gearbox has? 😁
Thanks for the great feedback.. they’re not very heavy I’d say roughly 40kg maybe ..
Some captions here and there would be good. I was curious about why the bell housing had grass cuttings inside it and why you greased the bolt holes. The hydraulic connector looked strange, is that something new or am I just hopelessly out of date?
That was a feathered clutch fabric inside the bell housing.
Other than that everything pretty normal in there.
🍻
Great video without all the silly chat 👌🤠
Great job and good photography
If it was me i would replace a flywheel seal ring while your are in
YOU did not mention that we have to set engine at Tdc mark
also i suppose we schould put mark befor removing clutch plate
Hi!
I congratulate you for the quality of the work.
are these floor tiles for the gym that you use?
Great work as always! Does It really matter unplugging te ECU before disconnecting the battery or nothing at all? Thanks for the video!
Hey Oscar .. ideally take the negative off.
On the other hand once ignition is off and car has gone into sleep mode .. it’s should be ok still.
Me gustan tus videos, siempre que puedo me tomo el tiempo de mirarlos...te felicito haces un exelente trabajo y me inspiras a hacer lo mismo! queria preguntarte si reutilizas el aceite de la caja de cambios o le pones aceite nuevo? Saludos desde Argentina!
Hola 👋
I would have cleaned out that area of the gearbox where the release bearing fits in....
Other than that,..top video thanks🤙
hi. this is a great video, very helpful!! would you be able to tell me how to remove the plastic grommit in the top of the bell housing? my slave cylinder looks different to this and the old fluid pipe does not match the new slave cylinder. old pipe is not compression fitting. wondering if someone has fitted a diesel one? please help sir.
Check the other version of this vehicle on the channel.
Top man ! Got the old one out today , new one back in tomorrow. Saved at least £300 . Subscribed and liked . Do you do 2010 Audi a5 1.8 tfsi?
Glad you’re finding the videos of some help 🍻🍻🍻🍻😁
Got the new one in tried it … it smashed a hole in the inside of the bell housing/ gear box right in line with the starter motor … the rivets in the new kit are 1mm higher than the old ones on the pressure plate . Do you think that could be the cause ?
✨👍🏼 the clutches warrior
Salut Sudine… Merci bient
Hi brilliant videos, youve given me the confidence to change my clutch on my sons corsa e, quick question on the corsa e theres a lower leg frame running from the rad pack that isnt on the corsa d. Can you still get the gearbox out with that there?
With corsa e you have to take the subframe off - otherwise it would be not enough space to remove the gearbox. At least talking about petrol versions.
Great bar for Milwaukee fuel what name guessed is it universal joint
How long did this take you to do? I’m having to change my flywheel soon because it’s juddering everytime I’m in 1st gear setting off. Sooo just trying to see if I can do it whilst working full time 😅 mine is a 66 corsa .
Hi, nice videos. One question, what happens if the parts you order doesnt fit on the car?
They always fit. But In the unlikely event it happens. I have a national account with ECP and can run to any of their branch and get a correct one.
Amazing content bro
why do you always put grease on the bolt holes?
Thank you m. Clutch
So that i am gonna mine
Of corsa 1.3cdti
Hi Kev, is this any different to the Corsa e (from 2015) thanks.
Hi my clutch on 13 plate hatchback is harder to push down just a bit more over past few months especially when warmer could it have dried out on pipes
It sounds like the clutch pressure plate is worn.
www.williamsmobileclutch.co.uk
Ok they looking at it. It’s not bad but I can feel it
What should i do my clutch isn't working ?
Replace it I suppose.
Hi Kevin. When I put my car on gear it doesn't move.. could this be the problem?
Sounds like it. But can’t tell you for sure.
How much will it cost me roughly to have my clutch fixed on my vauxhall corsa 2013
www.williamsmobileclutch.co.uk
hello is this the same thing on Opel corsa d OPC 2012? THANKS😊
Yea that’s correct.
@@WMCS thanks 😉😎👍🏼
Gracias por compartir saludos de san Luis Potosí México que herramienta tan efectiva tiene para centrar los discos donde la puedo adquirir
🍻🍻🍻
I live in Wolverhampton would you be able to replace the clutch for me ?
Yes of course.
What kind of car jack do you use?
hi kevin. where did you get your flexi-head for your impact gun. looks very handy
It’s from Mac tools online.
@@WMCS thanks kevin
you pick up a gearbox as if its made of Bolsa wood,,, bud👌
🍻🍻
Quality!! 👍
i dont know if these people can drive becose my car have 320000 km stil the same clutch and working perfect
thank you
How much would the charge come to for this service 🤔
Send us your details
Hi Kevin habe noch eine Frage wie alt bist du ?
Thumbs up from me buddy👍
Always nice Mike. Thank you.
Lindo auto 🤙
Nice 👍
🍻🍻
My Gosh, how much rust!
Car had been parked up for months.. 🍻🍻
👏👏👏👏👏👏
🍻🍻🍻🍻
👍👍👍👍👍
😎
hey
🥇 🍻🍻