I am no electronics expert... But it amazes me how all the components work so i ENJOY watching your videos Already a suscriber so thanks for posting Greetings from Mexico
dear tavz nice videos. you have good knowledge and experience.but i wana say when you put liquid solder put some flux before it will be more easy to fix and won't leave solder balls but anyway nice work
Greetings from Venezuela, excellent video, thanks for sharing your knowledge. One question on the BL there was 2.7 volts when it didn't turn on, what voltage should you measure there? when you replaced the IC it didn't say the voltage. Greetings
Hi i have hisense 85h6510g led tv and it has no backlight. Can you help to see which board is bad and what component could be bad. I dont have ser ice manual to check what voltages should be present when off and when on. I just dont want to buy wrong board or led strip for no reason. Thank you.
Hi Tevz how did you know it should have been 100 microfarads. 2nd question is are the same identifier on the back side of the board for the lactation of the capacitor.
Hello friend, I am a follower of your channel, ?? You will not have dump from Philips 32PFL5606H/12, SPI and NAND FLASH, greetings, the videos are very good...
My TV turns on…but goes black after few seconds. It turns on everytime, and goes off after a few seconds. Sometimes if I’m lucky, it doesn’t turn off, but usually it turns off. Any help will be appreciated.
You are an expert . You make me fall in love with Electronics
I am from India and i love your videos very much.
Thank you so much 😀
I real real appriciate your work sir and i have get new idea daily thank u so much.... Greatings from Tanzania
So nice of you
Best channel Mr Tevz keep up your videos are the best u explain everything very clear until u found faulty component and fix it u are the best thanx
So practical & simple. Again, thanks from Nigeria
Maraming salamat po Sir Tevz.
God bless po sa inyong pamilya.
salamat
Thanks for your the tutorial, simple, straight to the problem solution, success always👍
You are the best repair tvs, waiting for next video
Thank you so much 😀
Tanks fore tuturial master watching 👍👍👍🇵🇭🇵🇭🇵🇭💯🆗🆗🆗
great job again uncle tevez i missed the subtitles but i got the gist greetings from hungary robert's fan
kószónőm a feliratot
I wandered the inscription
Thank You Sir! It is very helpful! From ETHIOPIA!
Mr. Tevz, your explanatory method is very pedagogical. Thanks for sharing your experience. Kind regards. 👍👏🙏🙋♂️
Many thanks
I am no electronics expert... But it amazes me how all the components work so i ENJOY watching your videos
Already a suscriber so thanks for posting
Greetings from Mexico
Thank you very much!
Thanks for another great video Tevz. I learn something new every time. Best wishes.
Very welcome
Always first one to comment, well done Sir
Good work the on beatable mechanic
I love your videos sir, and thanks so much for sharing
My pleasure
Muy buena explicación y muy buen video muchas gracias por sus conocimientos con cada video suyo aprendo mucho mas. saludos cordiales
dear tavz nice videos. you have good knowledge and experience.but i wana say when you put liquid solder put some flux before it will be more easy to fix and won't leave solder balls but anyway nice work
Good great best nice job master thanks for sharing ❤️👍🏾👍🏾👍🏾👍🏾👍🏾👍🏾👍🏾👍🏾👍🏾👍🏾👌🙏
Thanks for watching
Very Nice. God bless you
You fix and make us happy, thanks.
Glad to hear that!
It would be nice if you explained -
The pencil eraser thingy
That’s some weird looking flux , grey
More detail would be nice
Thanks
Bob
Sir, can I ask what is the name of the cream used in soldering?
Understand very well and liked.
Newbie is watching master
thank you dearly my question is we can use STR w6000s without drive ic and mosfet for backlight driver?
Greetings from Venezuela, excellent video, thanks for sharing your knowledge. One question on the BL there was 2.7 volts when it didn't turn on, what voltage should you measure there? when you replaced the IC it didn't say the voltage. Greetings
And I love the roster in the back ground ! !
Sir Exelint information vido
Watching from north caloocan
Where is Caloocan? I'm watching from South Africa
the sn51dp ic as 5 pins and the ob3350dp 4 pins.how did you place the ic on the pad or does it matter.thanks
Good day Mr Tevs I'm loving ur videos I have a question how can I remove the IC Driver without hot gun?
Spread the soldering led and melt it up both side and lift up or slide through the tweezer
Excellent comme d'habitude 👍👍
Nice job bro 😊😊😊
Türkiye den selamlar
Troubleshooting expert ka sir..❤
Sir matanong ko lang kasi ung tv ko skyworth hindi maadjust ang backlight sa menu setting 0-100 walang pagbabago..
Thank you... What is the source of the voltage on pin No. 8 ic and how do we test the operating voltage from its source?
thanks 👍👍 👍
Watching po Master
Hi i have hisense 85h6510g led tv and it has no backlight. Can you help to see which board is bad and what component could be bad. I dont have ser ice manual to check what voltages should be present when off and when on. I just dont want to buy wrong board or led strip for no reason. Thank you.
Hi Tevz how did you know it should have been 100 microfarads. 2nd question is are the same identifier on the back side of the board for the lactation of the capacitor.
Nice work👍👍😎
Thanks 👍
This are wonderfull ticnition
Your content 8s good bt when you 7se an analogue meter it's hard to understand what you are measuring
Very nice 👍
Thank you 👍
terimakasih kawan , sangat bermanfaat bagi saya,...
Great videos
Nice
my led tv back light dont turn off if i power it of any ADVICE were to check on the motherboard?
excellent
Thanks!
I’m guessing the pencil thingy is a wire brush ! ?
Good job😊
Nice master
They used pmw ic as switch? Is it possible to build MOSFET as switch if we don't have ic replacement??
mosfet wont work alone, it need a driver.
Great...
In my case mosfet getting hot and tv turna off after few mintues....plz guide..
hello dear tevz !! i have the Ic Dap6a i cannot find it in my contry . do you have idea for equivalent ?? than you
Just like in this video, that type of IC are similar, try if you have a power board just like it.
@@tevzTVTevatronics thank you !!!!!
How did u disconnect the ic driver?
Hello friend, I am a follower of your channel, ?? You will not have dump from Philips 32PFL5606H/12, SPI and NAND FLASH, greetings, the videos are very good...
Super sir
My TV turns on…but goes black after few seconds. It turns on everytime, and goes off after a few seconds. Sometimes if I’m lucky, it doesn’t turn off, but usually it turns off. Any help will be appreciated.
Good boy
16:01 black capacitor blown
👏👏
C'est l'oscilateur?
yes
Queremos ver esse tipo de drive em portugues. angola
💝💖💗💙
❤👍🏻👍🏻👍🏻
🏆🏆🏆👍👍👍
good
tq. Sir.
using the reball paste makes my OCD flare like a nuke lol.
👍
So
Why don’t you tell us why the analog tester ! ?
Sony 40w800 kedip 3 kali tolong kerusakan nya apa makasih.
N-channel: red probe to G & black probe to S to make it ON. but you reversed them & it's for P-channel..
Эти тв что в коровнике стояли? Прежде чем нести в ремонт, хотя бы протёрли бы от грязи ! 😱
Fake and fraud
Very nice sir
Kuys tevz pwd mahingi po ung contact number nyu may papa ayos po sana ako laptop
DM ka nalang sa Facebook page ko