The saw blade sharpener will work if there is no set to the teeth. If there is a set you need to skip every second tooth and then reset the grinder to align with the other set.
Last one is deadly. Rpm on angle grinder is 11000 and normal cutting disks are rated for 12500. Your contraption can desintegrate and all thouse screws would become bullets. This might happen any time no warnings. Look up angle grinder accidents. Very dangerous. But is a good idea. For example with an anglegrinder with variable rpm at low settings might be safe enough. Cool idea. But not safe.
Есть пилы с прямым зубом с твердосплавными напайками. Теоретически их можно так точить, только надо поставить на болгарку алмазный диск по металлу, но не по камню (оригинальный по металлу дорогой) или приспособить алмазную чашку. Болгарку надо с регулировкой оборотов. Тысяч 5 оборотов не более. В самом станке, как я понял, диск в момент заточки фиксируется только прижимом к кнопке выключателя- это слабое место конструкции.
Yo personalmente,no recomendaría nada de esos inventos con la amoladora,porque la velocidad que tienen es muy grande por lo que las hacen sumamente peligrosas, hay que usar las herramientas como corresponde y para lo que fueron diseñadas
2 вариант фуфло, на самом деле заточка не происходит, а наоборот кончик зуба ударяется о диск и тупится, после чего диск маленько загибается и входит в плоскость. Зуб диска должен сначало зайти, а потом подводиться к заточному диску
Excellent tutorial! It's important to know this, and I appreciate you sharing your knowledge and experiences. Warm regards and, of course, a well-deserved like
Ladies and gentlemen boys and girls do not do this at home or anywhere else. Angle grinders run much too fast fothese crazy bodged up tools. You don't need them ,they are extremely dangerous are the there are many inexpensive tools that are designed for the purpose. They will do the job much better and a lot safer. Count your fingers and eye balls in the morning and before bed time....the number should be the same
I like in the first one when they pull out the square to prove that the piece of hollow metal tube they cut on a 45° angle is perfectly square. No shit it's a perfect 90, it always will be when you take the two pieces resulting from a single angled cut and rejoin the cut faces after flipping one around.
This isn't true at all. It's the result of adding up both of the angles. If you cut it at 80 degrees you have two 80 degree cuts, so 160 degrees total.
@@TylerDurden1400 Actually is the duplication of the cut angle, since the angles you refer to have to be equal every time. You will get 90 degrees only for a perfect 45 degrees cut. Congrats for spotting the mistake.
The lathe is too dangerous because of the high RPM of the angle grinder. But I think if we use drill instead of angle grinder or a variable speed angle grinder than it'll be much safer. But we will also need to add a support to the other end like a real wood lathe.
The second invention is the switch? good video, good work, good inventions, greetings. En el segundo invento para que es el interruptor? buen vídeo buenos trabajos, buenos inventos, saludos.
It's actually a horrible idea, it will only work once with realignment, you can easily sharpen 30 just using a vise and grinder or just use a bench grinder and hold the blade by the time you made this and sharpened one
Strange that you can still buy slotted screws........ A proper chippy still uses slotted screws if requested. They come out of painted hinges easier than rounded out cross heads. Seem like you have little experience good sir.
That's the first thing I thought of when I saw that. Seriously. Not sure if you watched this all the way to the end. hopefully not it gets a lot worse. Fucking dumb the shit going on in this video. I'm the idiot who watched it I guess.
Hab nur den Teil mit der flex. Säge gesehen, ich habe da noch einen Tip! Junge kauf dir lieber eine richtige Kappsäge bevor deine Hände Geschichte werden. Das sieht sehr wackelig aus. Sowas ins Internet zu setzen sollte schwer bestraft werden.
A good video of what not to do with your tools !!
Future Darwin Award Winner right there!
Most remarkable thing is that he still has all his fingers! 😮
My tought aswell 😅
Three ways how NOT to use an angle grinder. Buying the correct tool is going to be more effective then losing your fingers.
The saw blade sharpener will work if there is no set to the teeth. If there is a set you need to skip every second tooth and then reset the grinder to align with the other set.
An artist teacher who deserves thanks
Last one is deadly. Rpm on angle grinder is 11000 and normal cutting disks are rated for 12500.
Your contraption can desintegrate and all thouse screws would become bullets. This might happen any time no warnings.
Look up angle grinder accidents. Very dangerous.
But is a good idea. For example with an anglegrinder with variable rpm at low settings might be safe enough.
Cool idea. But not safe.
Agree 100%
A ahe rez agreee
Руководство по заворачиванию саморезов. Автор понятия ни о чем другом не имеет, но снято всё красиво. Настоящий "мастер"!
Valeu muito obrigado!
Brasil 🇧🇷
№2. так пилу нельзя заточить. (можно , но это неправильно. там углы заточки разные . через один зуб) , а у вас происходит спил зубов в 1 плоскость.
хрен с ним, с зубом, но заточным диском твердосплавные напайки, это реально жесть..
@@dioniseywings747 блин..таки да..куда я смотрел..
@@sergnemo2379 норм! Мне как то приспичило, я на алмазном плиткорезе такой диск затачивал........
Есть пилы с прямым зубом с твердосплавными напайками. Теоретически их можно так точить, только надо поставить на болгарку алмазный диск по металлу, но не по камню (оригинальный по металлу дорогой) или приспособить алмазную чашку. Болгарку надо с регулировкой оборотов. Тысяч 5 оборотов не более. В самом станке, как я понял, диск в момент заточки фиксируется только прижимом к кнопке выключателя- это слабое место конструкции.
Oh snap 😮
Can’t believe he is still alive!!!
Parabéns este amolador de serra ficou top de mais
So o amolador os outros são gambiarras.
Все просто и понятно, без выпендрежа.
This should be renamed to “How to unalive yourself with an angle grinder”
Yo personalmente,no recomendaría nada de esos inventos con la amoladora,porque la velocidad que tienen es muy grande por lo que las hacen sumamente peligrosas, hay que usar las herramientas como corresponde y para lo que fueron diseñadas
This is a great video, people will learn a lot from it.
Like what the inside of a hospital looks like...
Last one is really funny 🤣 🐟 🤣 too🎉🎉🎉
You are very creative.
I thought the lathe had a lot of play on the shaft.
Can you invent a homemade lathe to machine metal?
2 вариант фуфло, на самом деле заточка не происходит, а наоборот кончик зуба ударяется о диск и тупится, после чего диск маленько загибается и входит в плоскость. Зуб диска должен сначало зайти, а потом подводиться к заточному диску
Там вообще ничего работать не будет, жёсткости нет никакой
Чушпан пацанов на просмотры разводит! Все эти приблуды для лохов!!! А ему денюжка за просмотры!!!
№3 самый необходимый! Ну без него прям никак...
ЭЙ БРАТАН ТЫ КРАСАВА😊😊😊 ДАЙ БОГ ТИБЕ ЗДАРОВЙЕ УЗ Б🎉🎉
Awesome! 👍👍👍
Congratulations!. Thank you
Sharpens blade with opposing angles to all one angle...
You have done a great job
Excellent tutorial! It's important to know this, and I appreciate you sharing your knowledge and experiences. Warm regards and, of course, a well-deserved like
😊
TOP demais. Muito bom gostei muito, parabéns pelo seu trabalho ❤❤💯💯👏👏👏👏👏
Как убить хороший инструмент и сдетать шикарное глюкало😊😊😊😊😊
great for rounding the tips of the carbide teeth!
Thanks for showing you can still use slotted screws. Some people can't even hit the slot.
Cutting machine , very good
Nice creator!😊😊😊
Yea, that's what happens when you have no idea how wood saws work 🤔
Ladies and gentlemen boys and girls do not do this at home or anywhere else.
Angle grinders run much too fast fothese crazy bodged up tools. You don't need them ,they are extremely dangerous are the there are many inexpensive tools that are designed for the purpose. They will do the job much better and a lot safer.
Count your fingers and eye balls in the morning and before bed time....the number should be the same
Ini sangat luar biasa pemikiran yang sangat menakjubkan
Liarbiasa 👍👍👍
Very nice
2nd Idea (Thumbnail's ones) 😮😮
За травмы от "этого"вам не заплатят по страховке 😮😢😂😂😂
What is the name of that particular hinge ?
I can only suppose it is a /2 Cranked Hinge ?
Very good nice😊❤
Very nice work ❤❤❤❤❤❤❤❤❤❤good 😊
Really great
i like lathe project excellent, but instead of sharpening wheel we can but another one
muito bom mesmo
2nd one too good.
Think 3x when you creating such things... safety first
I like in the first one when they pull out the square to prove that the piece of hollow metal tube they cut on a 45° angle is perfectly square. No shit it's a perfect 90, it always will be when you take the two pieces resulting from a single angled cut and rejoin the cut faces after flipping one around.
This isn't true at all. It's the result of adding up both of the angles. If you cut it at 80 degrees you have two 80 degree cuts, so 160 degrees total.
@@TylerDurden1400 Actually is the duplication of the cut angle, since the angles you refer to have to be equal every time. You will get 90 degrees only for a perfect 45 degrees cut. Congrats for spotting the mistake.
very clever.
Я думал он ювелир по шнягам😂 а он оказывается игрушку делал
Станок#2❤понравился ❤
Hoje preferem o celular, este pinhão traz lembran😢!😂😂😂
marvelous
You do know those saw teeth are set at different angles?
Wrong grinding can cause you to cut in ways you don't want.
Absolute madness.
The lathe is too dangerous because of the high RPM of the angle grinder. But I think if we use drill instead of angle grinder or a variable speed angle grinder than it'll be much safer. But we will also need to add a support to the other end like a real wood lathe.
The second invention is the switch? good video, good work, good inventions, greetings.
En el segundo invento para que es el interruptor? buen vídeo buenos trabajos, buenos inventos, saludos.
It's actually a horrible idea, it will only work once with realignment, you can easily sharpen 30 just using a vise and grinder or just use a bench grinder and hold the blade by the time you made this and sharpened one
What I'm asking is, what is that white switch for?@@jamarjames9501
Os dentes da serra circular não podem ser amolados so em um sentido, eles têm ângulos diferentes. Não é muito útil essa coisa aí.
The blade sharpener was awesome... truly brilliant. You are a genius!!!!!
Muito bom 👍
Perdi alguns minutos da minha vida, dicas de como não usar uma esmerilhadeira.
Good luck.
Just buy a compound miter saw.
3:51 I hope he has a fire extinguisher
😀👍👍
❤❤❤
No me parece, demaciado ineficiente el prollecto, muy improvisado para mi, y tiene mucha inestabilidad ese torno, deberías perfecionarlo un poco más?
정밀작업은 어려워요. 레일의 유격이 엄청납니다.
Smart.
Why would i take advice from someone who uses slotted wood screws...?
Only matching screws left from that 1940s miscellaneous jar
Because if someone can use slotted screws as fast as you can use cross-head screws, they're obviously more skilled than you are.
Strange that you can still buy slotted screws........ A proper chippy still uses slotted screws if requested. They come out of painted hinges easier than rounded out cross heads. Seem like you have little experience good sir.
@@steveogburn6316the video is sped up
That's the first thing I thought of when I saw that. Seriously. Not sure if you watched this all the way to the end. hopefully not it gets a lot worse. Fucking dumb the shit going on in this video. I'm the idiot who watched it I guess.
The RPM off the angle grinder exceed the max RPM of the saw blade by a factor 2. Not that smart to use a saw blade on a angle grinder.
Так точить победитовый диск нельзя!!! Зуб скалывается,надо СРАЗУ ВСЕЙ ПЛОСКОСТЬЮ касаться -то есть прислонять его,а не проводить зубом
❤❤❤❤❤❤❤
Actually more like a miniature radial arm saw
Метрическа система измерения сущестует!
Time bomb waiting to explode, speed much to high! Use slower speed motor on wood lathe PLEASE!
Заточил все зубья под одним углом.... \ /.
🙏👍👍👍❤️❤️❤️
точильный станок вещь закрепляй болгарку на мертвой точке барашками а не шурупами.
К чему городить такой забор!?От скуки?😢
❤
Hab nur den Teil mit der flex. Säge gesehen, ich habe da noch einen Tip! Junge kauf dir lieber eine richtige Kappsäge bevor deine Hände Geschichte werden. Das sieht sehr wackelig aus. Sowas ins Internet zu setzen sollte schwer bestraft werden.
Откуда у него еще все пальцы? Игры с болгарками до добра не доводят
Não dá pra entender bolufas só eu pra perder temp😅😅😅😅😅😅
не показывайте это видео Доктору Дью, иначе у него случится пердечный сриступ!
Spin top cost a dollar 😂😂😂
❤🎉😮
crazy
То как все собрано развалится через 30 мин,или руки нахер поотрывает,что бы этому самоделкину их и по отрывало!!!
Woodworking hacks from someone using super glue on wood 🤔
2nd one is dangerous, no safety.
3rd one is wiggling..not properly fixed.
ты уже определись или в сантиметрах указывай или в дюймах
Like it
last one is bery risky
Opan the childdudh memory.waw.
🎉🎉🎉🎉🎉🎉🎉🎉
Люфт ,у мебельных направляющих,ещё тот!!!! Фигня на посном масле!!!!
What the hell is sabotaging !?
Not a tape measure in sight!
Few cuts is all what it takes to clog the drawer slides, sorry for the time I wasted watching