Fyi for any one watching this, after you spin the wheels be sure to squeeze the chain and move the sprocket into place that allows you to have your fingers the closest. Even with spinning the wheels a freewheel has room to play. By squeezing the chain you are ensuring it is as close to the front split sprocket as possible, which is dead center.
Hey I'm installing the power pedal kit right now. Unlike on this video, my split sprocket does not have a tight compression fit when fully screwed in. It spins freely. I have a Sur Ron X Black 2020. Has anyone else experienced this and will that middle screw be strong enough to keep it from spinning under force? I'm skeptical.
Can you post a video with audio which shows how much noise Congress from the one way sprocket and chain whole the motor is spinning and pedals are stationary?
Love this kit! Is there any way to make it faster? To at least 10mph? That way I can just pedal at times and get some exercise when riding with my girlfriend lol
I had to install the upper sprocket the opposite way. They would not line up to allow the srews to sink into the cutouts on the shaft. Otherwise very helpful.
I have never seen anyone have anything good to say about the Luna kit. The fact that it is attached to the swingarm was a deal breaker for me. This one is definitely the one to get.
The Sur-Ron can't be registered in the USA. If it has functioning pedals then it is considered a class 2 E-Bike and you don't have to register it and can ride it anywhere. Nobody intends to go around pedaling with these at 3 mph.
Ordered last Friday. Been waiting for a jackshaft spinning pedal kit since 2018. Even belt drive users can use this. I’m so excited.
ruclips.net/video/GQnQhVci4Sg/видео.html
Nice job guys! The community has needed a solid pedal kit for a long time!
I have been waiting for this video :)
Hey 👋 your kit is nice💯 i have only one question. Can i use a 420 chain on the sprocket?
Fyi for any one watching this, after you spin the wheels be sure to squeeze the chain and move the sprocket into place that allows you to have your fingers the closest. Even with spinning the wheels a freewheel has room to play. By squeezing the chain you are ensuring it is as close to the front split sprocket as possible, which is dead center.
Thanks, mine hopefully arrives 12/11/20
did it arrive?
@@T-Sav yes, actually a day early
Hey I'm installing the power pedal kit right now. Unlike on this video, my split sprocket does not have a tight compression fit when fully screwed in. It spins freely. I have a Sur Ron X Black 2020. Has anyone else experienced this and will that middle screw be strong enough to keep it from spinning under force? I'm skeptical.
Mine would not spin when the 2 outer screws were fully tightened. That is odd.
They sent me a new one that fit properly. It's all good now.
What does the power pedal kit do ? I'm get a pedal kit just don't know if I want/need the power pedal part of the kit. Pleas let me know. TY
The power pedal kit will propel your bike mechanically! www.kaniwaba.com/pedal-kits
Excellent tutorial and product👍
Can you replace the chain guard after install? Or does it interfere with the kit?
The chain will rub against the guard so I recommend removing it. It will work, but it will make a noise.
@@kaniwaba Would it work if I dremeled out a channel/hole for the bike chain?
@@Choatsy I think so yes.
@@Choatsy I'm going to mod the guard when I get mine
Can you post a video with audio which shows how much noise Congress from the one way sprocket and chain whole the motor is spinning and pedals are stationary?
Love this kit! Is there any way to make it faster? To at least 10mph? That way I can just pedal at times and get some exercise when riding with my girlfriend lol
Old comment but getting a different freewheel to change the gear ratio will give you a higher speed if you increase the size.
do they have different freewheels available?
I had to install the upper sprocket the opposite way. They would not line up to allow the srews to sink into the cutouts on the shaft. Otherwise very helpful.
Do you have to remove the kickstand sensor totally when using the Power Pedal kit
No, you can leave it or remove it, you decide.
Why dont you have a link to where to buy it
www.kaniwaba.com
Does this affect in any way with the torque/speed?
Not at all!
anyone can explain what's the difference between this and the surron kit ? thanks :)
construction quality and this one propels properly
@@JulienBrami
The position is moved forward also as it’s not attached to the arm.
This kit is not attached to the swingarm. The Luna kit is. This is much better mechanical speaking and safer.
I have never seen anyone have anything good to say about the Luna kit. The fact that it is attached to the swingarm was a deal breaker for me. This one is definitely the one to get.
@@richardstevens5961
Good point
Not on the arm
Nice
좌표 공유좀
www.kaniwaba.com
why would you do this to a Surron? are you really not able to admit to yourself and others that it is a motorcycle, lol, bow down to the man baby!
The Sur-Ron can't be registered in the USA. If it has functioning pedals then it is considered a class 2 E-Bike and you don't have to register it and can ride it anywhere. Nobody intends to go around pedaling with these at 3 mph.