Piaggio NRG MC3 Welding And Tinkering

[@petefroud5308]

No parrots Bert . Good job .

[@ProjectMan]

🐦🐦😂

[@alandykes2519]

Thumbs up again gary and thumbs up for welding job Martin 👍👍👍👍

[@ProjectMan]

Cheers alan 👍🏻

[@andycousins5016]

Lovely job 👏

[@markwiley9516]

Great job Gary and not bad from the old man

[@sdone7672]

Nice work Gary, nearly finished. 👍😀

[@ProjectMan]

Cheers mate 👍🏻

[@eadjh98]

Looks good Gary! Another great video on how to do it! 👍

[@ProjectMan]

Cheers David 👍🏻

[@normsmowers4758]

Top job on exhaust Gary makes all the difference a bit of tlc 👍👌

[@themowerman]

Good one mate.. I use the same spray paint.. I hear mum is busy cutting the Lawn..

[@ProjectMan]

Yer leaves a nice finish that paint.

[@silverghost8143]

thanks for the upload gary . stay safe fella .

[@jamesreeve9037]

Bike is coming along nicely, I bet it will fly without the restricter 👍

[@ProjectMan]

Should be nippy James 👍🏻

[@tinkeringtaylor3053]

great job Garry 👍

[@ProjectMan]

Cheers nev 👍🏻

[@a11csc]

coming on nice gary

[@calsgone6653]

Restoring an mc3 too at the moment and enjoying following this one, good work and looks much better. One note of advice for the future tho, shouldn’t heat wrap two stroke exhausts. Especially air cooled engines close to the cylinder, they need the heat to escape and the exhausts are made thin to help with this. Keep up the good work 👍🏽

[@ProjectMan]

Cheers bud for the info 👍🏻👍🏻

[@calsgone6653]

@@ProjectMan no worries mate 👍🏽

[@philipnewton7524]

Gary well done mate you making a great job on this bike someone will have a decent bike great chanel
Phil in stoke

[@ProjectMan]

Cheers Phil 👍🏻

[@andy_v4443]

nice repair on that exhaust that gary, BIG THUMBS UP FOR THAT

[@ProjectMan]

Cheers Andy v

[@martinburgess4814]

Good progress on t g b ,Gary. Works faster than dad

[@matthewharmer1656]

Exhaust looks really nice, just need to powder coat the main stand,... bike will look good when its finished.looking forward to the spray job.

[@ProjectMan]

Cheers bud

[@c849243]

You do such good work, Gary. Makes me wish I never left Bethnal Green!

[@ProjectMan]

Cheers Mark 👍🏻

[@michellesaxby669]

If you Disconnect the block on the back of the ignition barrel you can kickstart them

[@ProjectMan]

Iv got the key but yes I know that trick 👍🏻

[@annabellecarter6067]

Thats a nice workshop you have there.

[@JimJimpmjj]

Nice good progress, enjoying following the progress of this 👍 good stuff keep up the good work 👊🤙💪💯✅👌

[@ProjectMan]

Cheers James 👍🏻

[@ricksmowers5094]

Great vid project man exhaust looks great

[@garyclifton2180]

Coming on nice gaz

[@benjyboichambers6030]

👍🏻👍🏻

[@leemarrison4721]

rubber boots on the HT lead !!!

[@ProjectMan]

That what bike shop supplied

[@reecesteward3062]

Hi Gary mate selling Yamaha jog run but cut out

[@ProjectMan]

Hi bud send me a email my email address is on my about page 👍🏻

[@reecesteward3062]

@@ProjectMan done it mate

[@ProjectMan]

Sent pm