What is the difference between the 2 different calibrations styles ? I have the wedge to calibrate with 1 clamp, My kit also came with the 2 small metal bars to calibrate lowering the adjuster all the way and raising the extender , Why is there 2 separate ways can you please explain ? Thanks
Helllo! I am not sure that I understand which is the second type of calibration. There's just only one :) Indeed, it comes with 2 bars and each bar for each clamp. There' no difference in calibration at all. It's just for convenience to not remove them each time when calibrating.
Axicube worked perfectly for a couple months, now does not accurately give angle, and attempts to recalibrate do not work. Sets at anywhere between 17.6 and 19.9 on the 14 deg calibration angle with press and hold. Defective? Hard reset?
So i calibrated axicube the way u showed, and when i double checked deviation with angle block cube comparing it to center console, deviation is 1.6 degree, so axicube is off by 1.6 degree
How do you reset the cube itself back to 14 degrees? When I calibrate it says 14.6 degrees. Then If I do it again in the same spot it reads 13.8 degrees. Just bought Pro Hunter and having issues with Axi-Cube. Thanks.
John, sorry for the late reponse. I understand the problem. Plese, contact us to sales@tsprof.com and say that Nick told you to contact him. I will provide you with a special video about how to fix it.
@@TSPROFSharpening oh, i think i fixed it now. one lf the whole milled clamp was way tighter than the other and wasn't seated properly in yhe crossbar so i got a wrong reading.
If I mainly use the signal clamp should I calibrate with it please answer
What is the difference between the 2 different calibrations styles ? I have the wedge to calibrate with 1 clamp,
My kit also came with the 2 small metal bars to calibrate lowering the adjuster all the way and raising the extender , Why is there 2 separate ways can you please explain ? Thanks
Helllo! I am not sure that I understand which is the second type of calibration. There's just only one :) Indeed, it comes with 2 bars and each bar for each clamp. There' no difference in calibration at all. It's just for convenience to not remove them each time when calibrating.
Any news on when the axicube will finally be available for the kadet pro?
Sill working on this.
У меня уже есть сегодня взял для kadet pro ))))
Is there a video using the axicube and the universal convex attachment on the KO3
There's no far. As soon as we find a suitable knife, we'll do. But the approach is the same. There's no difference at all.
Axicube worked perfectly for a couple months, now does not accurately give angle, and attempts to recalibrate do not work. Sets at anywhere between 17.6 and 19.9 on the 14 deg calibration angle with press and hold.
Defective? Hard reset?
sales@tsprof.us - please contact this mail in we will replace the defective device. This case is unusual, most likely there is a hardware problem.
Hi, is there a troubleshooting manual or video?
Hello! What was the problem?
@@TSPROFSharpening it is ok I have already emailed, thank you
ETA on re-stock (EU shop)?
So i calibrated axicube the way u showed, and when i double checked deviation with angle block cube comparing it to center console, deviation is 1.6 degree, so axicube is off by 1.6 degree
Please, shoot a video for us with the problem and send it to us to sales@tsprof.com. We'll examine the issue.
How do you reset the cube itself back to 14 degrees? When I calibrate it says
14.6 degrees. Then If I do it again in the same spot it reads 13.8 degrees.
Just bought Pro Hunter and having issues with Axi-Cube. Thanks.
John, sorry for the late reponse. I understand the problem. Plese, contact us to sales@tsprof.com and say that Nick told you to contact him. I will provide you with a special video about how to fix it.
my axicube shows 10.9 dps with the whole milled fillet clamps. am i doing this right?🤣
Not sure it I understand you :) Can you describe?
@@TSPROFSharpening oh, i think i fixed it now. one lf the whole milled clamp was way tighter than the other and wasn't seated properly in yhe crossbar so i got a wrong reading.
Спасибо
JUDAS PRIEST!!🤘😆🤘
😎🤘
Already fixed. Sorry for the inconveniece 🙃
used it for about a month or two and now it won't start anymore, even though it's fully charged. what a disappointment😢
Hello! Please contact our customer service (sales@tsprof.com) we will see what we can do to solve this issue.