Great, but what did you do? You only changed the motor to require a higher voltage (and maybe slightly more output if you could possibly get more by adding a turn or two from the following formula) Motor Force = B*L*A (B = magnetic strength, L = length of wire in the magnetic field, A = current in the wire). So you can see here that if you use smaller diameter wire, you can make more turns but you must also use less current. Therefore, you have not increased the motor torque at all. But you may have changed the kVA so now it may go faster with 3x the voltage with no load but the motor will likely not match the gearbox and the intention of the motor. The original motor designers match the kVA (motor windings, voltage and current, etc.) with the torque and gear reduction and with the speed at which the engine needs to turn.
Bro starter motors are designed for running for a small period of time. By decreasing the gauge of the wire he has reduced the amount of current consumption, so that motor could run for a longer period of time. So he could use it in an E cycle.
70 gramas de Fio #23 AWG , não esquecer de usar papel isolador ,se enrolar sem isolação vai ocorrer um curto. Fio #23 AWG , não esquecer de usar papel isolador ,se enrolar sem isolação vai ocorrer um curto. Wire # 23 AWG , use 70 gramas de fio, do not forget to use insulating paper, if it is rolled without insulation, a short will occur.
... the anealed coil would melt and short on overheat ..you need a big solid copper coiling bar..or similar..it was documented starter motor recommended to run continuesly for only 3 min....
If the current is limited, it can run as long as it doesn't overheat. The current limitation is done by rewinding the motor with thinner wires. The starter does get weaker and faster by this, but it will heat up slower, so it will run for longer. Good for small electric go-karts. But yes, the bearings will fail sooner.
This is a good video. Thank you. Educating people on the basics of rewinding a motor. However, as others have mentioned, reasoning to rewind a motor would be repair melted, otherwise shorted, windings located using a resistance reading multimeter… And please note- !must utilize OEM gauge, length, composition wire as originally installed otherwise changing +/- winding turns, the thickness or gauge of the wire, the orientation of which they are wrapped around, will all change input/output spec calculations based upon required basic engineering formulation. If one does not adhere to the required formula, they will waste a lot of time, cause damage to other components, otherwise, potentially learn how the haphazard process 💫 potentially valuable advice, research PPE regarding chemicals used, and the black powder you will find is also a toxic inhalant. Please research safety and correct process. You will inevitably have a better time!! Good luck.
कितने गेज की तार है, कितने स्टेट का अमीटेटर है कुछ बताया ही नहीं, किसी फिल्म की नकल करके youtube पर लोड कर दी, अगर तुम्हें पता होता मुहं से बोलकर बताते, जहां म्यूजिक चलाया हो वहां वोग्स दिखाया जाता है.
Hello Realy hope you can help me. Iv got a Fiat 128 1974 model My starter ONLY keep crunking (stuck) if cold. Then i take of negative from battery and it stops. Then put cable back. Then start easy whole day. No problem. In morning it stuck when start for 1st time the day. Its summer now in South Africa. But in winter it stuck 2 to 3 times. Then no problem to start. If car is in sun. And start for 1st time the day sometime start 1st time without keep cranking. Sometimes keep crancking ONLY ones. Then start easy. After it starts. I switch of and starts again. I did it 6 times. Off and start off and start. No no no problem. I take of ignition switch wire from starter and jump it straight to battery this morning. Same problem. Stuck and keep cranking. Have to take of negitive wire to stop. Then try start again. Start at ones, no problem Rrrrealy hope someone no what cause this. Thanks so much.
you did to lower the ampherage and also lower the torque... by changing the smaller size of the copper wire also lower or extend the consumption of battery power... ???? is it sufficiently capable to pull forward speed of the bike... thanks...
estas bien wey como quieres hacerlo mas potente usando un alambre la mitad de grueso que el original ??? uno mas delgado significa menos corriente y en consiguiente menos potencia jajja no mames con ese bobinado tendrias que usar36 v
आप कंजुस आदमी हे,,साथमे कोमेंट करना था,,,आभार,,
Dude... Say somethings... Or at least write Some imp notes like wire guage....
Great, but what did you do? You only changed the motor to require a higher voltage (and maybe slightly more output if you could possibly get more by adding a turn or two from the following formula) Motor Force = B*L*A (B = magnetic strength, L = length of wire in the magnetic field, A = current in the wire). So you can see here that if you use smaller diameter wire, you can make more turns but you must also use less current. Therefore, you have not increased the motor torque at all. But you may have changed the kVA so now it may go faster with 3x the voltage with no load but the motor will likely not match the gearbox and the intention of the motor. The original motor designers match the kVA (motor windings, voltage and current, etc.) with the torque and gear reduction and with the speed at which the engine needs to turn.
He cant understand you
Bro starter motors are designed for running for a small period of time. By decreasing the gauge of the wire he has reduced the amount of current consumption, so that motor could run for a longer period of time. So he could use it in an E cycle.
@@KundanKumar-ez5cm Ok, but his title says "How to make upgrade Starter Motor 12V - Super Powerful" which is misleading.
Abhishek Sahani Nautnwna 🤝🙏💓💓 👌👌 Super video
Nice ❤️🌹👏💋💋
But if you use a thinner wire and you turned it more, shouldn't it run with less power if you apply the same tension?
Thanks bhsi very very thanks
Require a reply. If without winding rotar
if we use magnets will it work? Just like BLDC.
more video about starter motor. motorcycle ^^ more power
Sir yes new coil wire agar lagadenge to new jaisa kaam karega na??? Reply kijiye
I'll translate. How to make a 12v starter work on 36v.
I have a 135cc moped and I have upgraded it to 205cc , now obviously the starter doesn't work. What should I do? Buy a bigger one?
Good jobs...
Thank you so much 😀
What swg 22*23*24 nong
Muito bom gostei 👍
Super
Thanks
Superb
what is a number size of copper wire and how many rounds per coil..?
more power.
Hi nice video thanks.
What size was the old wire?
And what size is this new wire?
Thanks
Let me check
bhai 5 side double wire hogi kya ?
Isme kitne swg ka vire use kiya h
Thanks how to rewind starter motor suzuke van
Thanks how to rewind starter motor suzuke van
its like thinner wire u used after removing the second wire
I thought you were going to convert to BLDC motor.
That's what I thought as well
Yrr ye jo carbon roller jo he copper ka ye kaha se purchase kare
I thought the thicker the brass coated wire spins much faster......
Ok so feed it 24v and be careful not to melt it?
What am I missing here?
Genius!
If you make step 6 the results will be better
70 gramas de Fio #23 AWG , não esquecer de usar papel isolador ,se enrolar sem isolação vai ocorrer um curto. Fio #23 AWG , não esquecer de usar papel isolador ,se enrolar sem isolação vai ocorrer um curto. Wire # 23 AWG , use 70 gramas de fio, do not forget to use insulating paper, if it is rolled without insulation, a short will occur.
the motor became too slow 😂😂😂😂
Dùng dây mấy li bạn.
mantap
ভাই এটাকি বাড়নিস না সুপার ঘুলু
Sir please make a video how to out a negetive wire and saprate frome ground in this type of self stater
Please share if u find it.i also want to know.
2nd can i use 12 volt or 24 volt adaptor instead of battery?
Wire gage
And rounds
Son gloves exist you know?
Sir binding ke pehle kitne ampior tha or bad me Kitna hua plzz bataye
Bs6.ka.self.ke.bainding.tar.ka.nambar.batavo
Sir wending wire which kge
Before conversion of stater motor, how many turns are there in original stater motor
5 turns
Most starter motor for motorbikes have between 6 and 8 turns of insulated copper wire per room.
... the anealed coil would melt and short on overheat ..you need a big solid copper coiling bar..or similar..it was documented starter motor recommended to run continuesly for only 3 min....
If the current is limited, it can run as long as it doesn't overheat. The current limitation is done by rewinding the motor with thinner wires. The starter does get weaker and faster by this, but it will heat up slower, so it will run for longer. Good for small electric go-karts. But yes, the bearings will fail sooner.
How much price of motor bro please reply
How many rpm before and after...??
12volt. Self. Binding. Tar. Ka. Nambar.batavo
What is motor modle
This is a good video. Thank you. Educating people on the basics of rewinding a motor.
However, as others have mentioned, reasoning to rewind a motor would be repair melted, otherwise shorted, windings located using a resistance reading multimeter…
And please note- !must utilize OEM gauge, length, composition wire as originally installed otherwise changing +/- winding turns, the thickness or gauge of the wire, the orientation of which they are wrapped around, will all change input/output spec calculations based upon required basic engineering formulation.
If one does not adhere to the required formula, they will waste a lot of time, cause damage to other components, otherwise, potentially learn how the haphazard process 💫 potentially valuable advice, research PPE regarding chemicals used, and the black powder you will find is also a toxic inhalant. Please research safety and correct process. You will inevitably have a better time!!
Good luck.
thanks you
@@ksthacks can we make drill machine with using this motor
how to rewind 7 slots of a armature with 7 hangers of commutator ?????
Size of wire
1.0mm
कितने गेज की तार है, कितने स्टेट का अमीटेटर है कुछ बताया ही नहीं, किसी फिल्म की नकल करके youtube पर लोड कर दी, अगर तुम्हें पता होता मुहं से बोलकर बताते, जहां म्यूजिक चलाया हो वहां वोग्स दिखाया जाता है.
How many millimeters are you using the wire?
ban sài dây 0.7 ->1mm là được nha
@@ksthacks adu biết tiếng việt luôn hả. E tưởng bác sài English
@@tienngyen6482 :))))
@@ksthacks lại mía rìu qua mắt thợ rồi. Ngại quá ngại quá
Wow you decreased the torque and increased the RPm which is not required in starter motor
He did not rewimd that for a motorcycle he juat showed us how to rewire it
Anong number nag magnetic wire
Please anybody let me know the process to seperate negetive wire from ground...
And 2nd can i use 12 volt or 24 volt adaptor instead of battery?
y u r not giving replay
How to armechar riwinding in hindi language video
ये मोटर कितने रूपया की है
But power is low..
Bhi ya gear motor kai ke ha
Where I can get this motor pls??
Is a 12V Motorbike Starter Motor
Bhai ye kha par milta hai
Ye jailing bike main laga howa ata hai
Hello
Realy hope you can help me.
Iv got a Fiat 128 1974 model
My starter ONLY keep crunking (stuck) if cold. Then i take of negative from battery and it stops. Then put cable back. Then start easy whole day. No problem.
In morning it stuck when start for 1st time the day. Its summer now in South Africa. But in winter it stuck 2 to 3 times. Then no problem to start.
If car is in sun. And start for 1st time the day sometime start 1st time without keep cranking. Sometimes keep crancking ONLY ones. Then start easy.
After it starts. I switch of and starts again. I did it 6 times. Off and start off and start. No no no problem.
I take of ignition switch wire from starter and jump it straight to battery this morning. Same problem. Stuck and keep cranking. Have to take of negitive wire to stop. Then try start again. Start at ones, no problem
Rrrrealy hope someone no what cause this. Thanks so much.
I won't car self motor for run long time (15min) how can I modify ?
Reduce the copper size, just like he did
what size of the copper that you replace? thank you
26#
محتاج متور مثل هذا --- كيف أحصل عليه ؟
what size is the wire,and how many turns
0.5 ->1mm
10 ->15 turns
Какой стартер
Cuantas vueltas sedan por cada bobina.esplicame mas
superb.......... but, what is the size of the wire & no. of turns
y u r not giving replay
Itu pakai aki berapa? Terus mau di taruh di motor apa
you did to lower the ampherage and also lower the torque... by changing the smaller size of the copper wire also lower or extend the consumption of battery power... ???? is it sufficiently capable to pull forward speed of the bike... thanks...
yes
Also I guess this makes possible to run the motor continuously without over heating.
I THINK ITS FAKE
Ye Mota kon see. Battery se ful speed nachega
What is Wire no?
26
what type of motor is this
honda dream
Where can I get this motor from?
Is there an electrical device has a motor like this?
It's from Chinese mini trail bike
Đường kính dây bao nhiêu vậy admin
Cỡ 0.5 là đc bạn
Tiện thể cho e hỏi dùng chế xe điện ổn không . Thấy a thử 24v có được không cảm ơn admin
@@xuanquy3009 24v chạy ko tải thấy oke,ko nóng nhưng chưa thử tải nên ko biết có nóng ko
@@quangquoc5343 Anh thử chế vào xe điện hôm trước xem sao để e làm 1 cái với ạ
Tora tera tera yara
hmmm...
Tar. Ka. Nambar.batavo
Beter no comand,no answered
hoá ra là thằng vn àk
tao là thằng vn đây
Tarkanambarbtavo
Too. Volatile. Keep. Self. Binding. Keep. Tar. Katie. Nambar
motor wiper mobil apa yg torsinya tinggi om ?
Ķ
This is not upgrade, but downgrade
متورايه
estas bien wey como quieres hacerlo mas potente usando un alambre la mitad de grueso que el original ??? uno mas delgado significa menos corriente y en consiguiente menos potencia jajja no mames con ese bobinado tendrias que usar36 v
what is a number size of copper wire and how many rounds per coil..?
more power.
What swg 22*23*24 nong