I know we use cordless drills at work that have these 775 motors in them and just one can snap a 3/8 in stainless steel tap con in half in a split second. They're crazy strong for their size. So 6 of them in parallel would provide plenty of torque for something like a go cart or rc truck. It would be an interesting project for sure.
imagine you have this engine and you put it on a big scale RC truck (semi truck ) and just pull a freaking heavy load out of this like 30-40 bricks on a homemade rc trailer
@@Argosh you can completely submerge a brushed system. and most brushed systems achieve a high enough speed to have fun. These motors are in fact not trash they will outlast any brushless motor you have 10x over. Through the mud, rain, sleet, snow, driving into a lake. Your brushless motor just started rusting thinking about it. Don't judge just because you wouldn't use it doesn't make it trash. You judging a proof of concept in fact makes you trash.
@@dillanpoling4497 hm. I'm not sure you know how stainless steel works. Matter of fact one of the major advantages of bldc motors is that you can encapsulate them. Coals don't do particularly well in submerged applications. Have you even tried running anything in the environments you just specified? Because I have. You can fully submerge a bldc motor without any special preparations and it will last however long you need it. Coating the stator on epoxy will make it last in saltwater or any other rough environment. I have operated 5kw bldc motors in this exact way quite successfully. Since you decided to make this personal I assume you're completely clueless. Come back when you've actually done anything with proper power electronics, and no, that doesn't include anything even remotely as whimpish as the couple hundred Watts this kind of garbage provides.
@@anasijaz9498 Angled beveled gears. Like normal beveled gears, however they intermeshed in an angel. The ones shown were pulled from an angle grinder. en.wikipedia.org/wiki/Bevel_gear
Guarantee this guy has a cool cool job and he just makes these videos for fun little trinkets lying around his house that he made for fun but takes everything else seriously because I doubt anyone who has this much stuff just does this
Question: are six motors less 'efficient' than one larger one ? more gear friction, 'interference' between the 6 motors, more wiring, more to go wrong. Thanks for any answers.
So I had some of the same thoughts but wondered if they are all getting the same power? He wired them in parallel which should get them all full power but will eat power faster than if he had wired them in series but they would divide the power among them. Parallel would make more power/torque but series would make much less power/torque but would run much longer on the same amount of power. If the motors are not in good phase which they most likely not since they looked like slightly different makes. So same power output but different years or companies so they might have different windings or magnet setups. This could make them fight each other a bit using more power at a faster rate.
in a way yes but a larger motor has one down side more rotational mass there is a limit to how fast you can spin something before it tears itself apart i am not gonna get in to all the fancy math behind it but for arguments sake we will say one of those motors makes 1kW and 10nm but can spin up to 20,000 RPM with 6 you can have 6kW and 60nm at 20,000 RPM but a larger 6kW and 60nm motor can only get to 10,000 RPM you could use a step up gear to get 20,000RPM but you lose about 1/2 of your torque and power. its the same thing Tesla uses instead of one large AF motor its 2 smaller ones working together and similar on high speed trains instead one large slow motor they have smaller ones placed across lots of axles meaning the same power higher RPM the load is spread out over a bunch of axles meaning more grip and a fair amount of redundancy.
Stone Mason it’s the same logic when it comes to car engines such as a 4 cylinder vs 8 cylinder but of course the more power delivered by the individual extra pistons! Motor in this case compensates for the power lost in the process of gears which is why in transmissions the gear ratios are different upon all gears to change the tourque needed. In summary more power is made by an extra motor/ piston and less is lost to friction and gear therefore more efficient
multiple small motors is better than 1 big motor when it comes to operational assurance but there will be more moving parts hence more to maintain. Gearings also consume some power and it require ratchet type gears to compensate less performing or non performing motor which will cause drag
It is amazing.. It can be developed to be used in more powered machines in factories. I think it is good to keep all the gears in closed gear box to avoid corrosion and to decrease the noise.
The benefit of the motors is they take the load off of one another more than adding speed. The best use of this thing is for applications that need a ton of torque, like drills. The array of gears to get this thing ready for a vehicle would require a transmission, so yeah it could be done, but the top speed wouldn't be what you'd expect. It would get to top speed pretty quick though.
They might broke each other if they are not loaded but let's say , every single motor has same amount of coil lenght inside so they can't broke each other but if some motor has 1 extra turn than others , this single motor can likely burn out because it spins a bit faster and pulls other motors to achieve maximum speed of that one motor but it will take a long time to burn one single motor with 1 extra turn
I get here you’re coming from. Wiring 6 DC motors in parallel to drive the same shaft like that, all 6 motors must have exactly the same impedance across the windings, exactly the same field strength in the magnets, and exactly the same RPM. If just one motor is the tiniest bit out of spec from the rest, it’s going to either drag or be dragged by the others, which will cause it to overheat and burn out quickly. A way to make this work well would be to have electronic speed controllers on each motor so they can all be synced up. Set up right, this would be a good way to get a big load of torque from small cheap motors!
Так а смысл заморачиваться, если практического применения никакого у такой поделки нет. Если нужно больше мощности, нужно взять другой мотор, не будет потерь на трение и грохота шестерней.
you might use it as a high power generator if you power 1 motor and connect all the other 5 in parallel, you can have 5 times the output current from the 5 motors if you power 1 motor with 12 volts 1 Amp (assuming the motors run on 12 volts 1 Amp), you would 'theoritically' have 12 volts 5 Amps on the paralleled output at no load and by using an SMPS, you can step the voltage up with the boost converter or step it down with the buck converter, this way you can have a powerful generator made by you and don't have to rely on free energy devices to help you (Note : free energy doesn't exist)
Nice video! Lots of efforts! But lots of losses in such designs. As motors design is not perfect there will be minor difference in speed of each motor. As if some motor lag or leads gears will wear out pretty quickly. Also if motor is loaded with some torque these losses will change dynamically as load will not distribute equally over the shaft length and as motors are also not perfect. Also as motors are inductive loads and connected in parallel configurations current and back emf spikes will spoil the whole design. I just wanted to tell the science behind it. That's it. Else cool work man!!!! Thanks keep it up
Would have been better if you could switch those motors individually depending on your load requirement That way you would save precious juice from the battery
atleast he's smart enough to know that it's still a motor considered since it's still electric powered. A motor is electric and an engine is gas powered.
Absolutely agree, this configuration is VERY but VERY inefficient, on any side you see it has no practical uses, just as a curiosity, this configuration is used in combustion engines because it is the most practical configuration that can be used in these engines can
@@ИванИванов-ф6ю7к 👍 😁 Шпонить не представляется возможным, мал размер, да и лишнее это, при таких задачах. А вот "сожрать" на горячую будет самое то, этого достаточно. Есть ещё один серьёзный косяк, про это тоже никто не пишет : При посадке шестерни на вал двигла,(задаю загадку) -- Куда упрётся(где опора/твердь?) медная втулка? И чем это чревато?
Yo that would actually be really cool! A motor with a high torque potential with all 6 sub motors engaged, but a more efficient motor at low torque with only 1 or 2 engaged
No no you can. Easier way is with power strip, all you gotta do is plug it into itself after its been plugged into the wall for 5 minutes and infinite energy!
i actually thought about this design as a kid...nice to see someone actually bring it to life...
Same
Same here bro
same
the simplicity of dc motors bro. cant be beat.
How to build a motor with motors😂👋
So funny 😏
But you very
@Neo still doesn't make any sense
@Neo yeah bould you could just buy or make a good gear?
@Neo a transmission
Love u from Indian occupied Kashmir
Pakistan occupied kashmir
That set up would be awesome on an off road RC truck....would be an interesting build.
He can build this Rc Truck
I was trying to comment on it but I saw ur comment ya it's a very good idea for a powerful engine for a truck and it was my dream in my saller age
@@hermes1878i would love to see it.
I know we use cordless drills at work that have these 775 motors in them and just one can snap a 3/8 in stainless steel tap con in half in a split second. They're crazy strong for their size. So 6 of them in parallel would provide plenty of torque for something like a go cart or rc truck. It would be an interesting project for sure.
imagine you have this engine and you put it on a big scale RC truck (semi truck ) and just pull a freaking heavy load out of this like 30-40 bricks on a homemade rc trailer
Bonjours Bon souhaite bienvenu c'est important merci tout monde
So a 1:5th scale semi truck?
@@theimprovisor8998 nah I think that’s to big just make a enough room to put the motor in
i am making , but with 555 dc motor . v8
ruclips.net/video/aG9HoBfmzfU/видео.html
Nice concept! Just can’t imagine the torque! Great!
No need to imagine. It's not a lot. These motors are trash. I have no clue why anyone would use brushed motors at this point in time.
@@Argosh you can completely submerge a brushed system. and most brushed systems achieve a high enough speed to have fun. These motors are in fact not trash they will outlast any brushless motor you have 10x over. Through the mud, rain, sleet, snow, driving into a lake. Your brushless motor just started rusting thinking about it. Don't judge just because you wouldn't use it doesn't make it trash. You judging a proof of concept in fact makes you trash.
@@dillanpoling4497 hm. I'm not sure you know how stainless steel works. Matter of fact one of the major advantages of bldc motors is that you can encapsulate them. Coals don't do particularly well in submerged applications.
Have you even tried running anything in the environments you just specified? Because I have.
You can fully submerge a bldc motor without any special preparations and it will last however long you need it. Coating the stator on epoxy will make it last in saltwater or any other rough environment. I have operated 5kw bldc motors in this exact way quite successfully.
Since you decided to make this personal I assume you're completely clueless. Come back when you've actually done anything with proper power electronics, and no, that doesn't include anything even remotely as whimpish as the couple hundred Watts this kind of garbage provides.
Watts x rpm = torque
ruclips.net/video/aG9HoBfmzfU/видео.html
5:45 cut your nail haha. very good video 👍
coke nail
Now, implement this engine in a toy car
up vote
What’s tha name of gears plz tell me
@@anasijaz9498 Angled beveled gears. Like normal beveled gears, however they intermeshed in an angel. The ones shown were pulled from an angle grinder.
en.wikipedia.org/wiki/Bevel_gear
ruclips.net/video/RY1z9ldqt4s/видео.html
Mini go cart maby?
I'm jealous of his materials. If I have materials like that, I could do something that could help. 😔
Same😔
Same
Me too😶financially back
Wow your skill sets are amazing my friend! I truly enjoy watching your experiments come to life.
😂🎉def😂ruff egr get ffdwfhgfv leg
You should make a rc car with this if you agree
⬇️
My face was like nooo when u stab ur hummer in the motor without any back support...anyway i love every single of your video...
The back support was the other end of the shaft? Unless I have missed something.
You are soldiering very well👍
متابعك من العراق
Guarantee this guy has a cool cool job and he just makes these videos for fun little trinkets lying around his house that he made for fun but takes everything else seriously because I doubt anyone who has this much stuff just does this
he did all the motor bushings with sand paper ,but has a lathe.. fascinating
Machining that amount of copper with a lathe is impractical and overkill.
He can't use the lathe, copper tubing gets collapsed so easily with 3 Jaw chuck with the slight amount of tightening.
I said that when he broke out. Mid video probably went to friends or work for it I would have been more excited to see the whole project DIY tooled
@@EcchiPlaysGamesgood reply
Good if you have shown the usage of this coupled motor as well.
Can you tell me what is the use of this🤔🤔🤔
Yes
@@MacXPro so why he bulid it
@@Ahmadisop132 just wait for the next vid.. hahaha
May be this v6 use to make vehicle
Nice song👌👌
Make electric boat using this v6 775 motor
what do you say
@@sozdar2976 V6:v
Or scoter
I can sense the burning smell of coils by watching this. 😂
Any guy realised that if you power one Motor the others generate electricity
Yes I realize that
No
@@hodanadan6701 cool thx i was actually wondering
In the back of my mind, I hear:
"This.... is Elon Musk"😎
"Tesla's co-founder and CEO"😂
This is probably the patent for Tesla models' motors😎
This is a good motor for a small boat. Not advisable for trikes, they heat up too fast.
he needs linus help then to water cool
@@MohdAzylee bruh. lol
@@MohdAzylee that man is insane. He water cools everything. EVEN A CALCULATOR 😆
@@troyguererro0898 😂😂😂 hes da best
Boat in online :D check his channel
I really2 like Creatif Chanel, Cool bro strong V6 motor N high torque
Question: are six motors less 'efficient' than one larger one ?
more gear friction,
'interference' between the 6 motors,
more wiring, more to go wrong. Thanks for any answers.
So I had some of the same thoughts but wondered if they are all getting the same power? He wired them in parallel which should get them all full power but will eat power faster than if he had wired them in series but they would divide the power among them. Parallel would make more power/torque but series would make much less power/torque but would run much longer on the same amount of power. If the motors are not in good phase which they most likely not since they looked like slightly different makes. So same power output but different years or companies so they might have different windings or magnet setups. This could make them fight each other a bit using more power at a faster rate.
in a way yes but a larger motor has one down side more rotational mass there is a limit to how fast you can spin something before it tears itself apart i am not gonna get in to all the fancy math behind it but for arguments sake we will say one of those motors makes 1kW and 10nm but can spin up to 20,000 RPM with 6 you can have 6kW and 60nm at 20,000 RPM but a larger 6kW and 60nm motor can only get to 10,000 RPM you could use a step up gear to get 20,000RPM but you lose about 1/2 of your torque and power. its the same thing Tesla uses instead of one large AF motor its 2 smaller ones working together and similar on high speed trains instead one large slow motor they have smaller ones placed across lots of axles meaning the same power higher RPM the load is spread out over a bunch of axles meaning more grip and a fair amount of redundancy.
This only for RUclips fun. Better to buy a larger motor According to application.
Stone Mason it’s the same logic when it comes to car engines such as a 4 cylinder vs 8 cylinder but of course the more power delivered by the individual extra pistons! Motor in this case compensates for the power lost in the process of gears which is why in transmissions the gear ratios are different upon all gears to change the tourque needed. In summary more power is made by an extra motor/ piston and less is lost to friction and gear therefore more efficient
Yeah that interference question ...... it hoops in my mind every time I see motor coupled together in this way🤔
Fantastic torque it will generate
This dude's stash, tho....Looks like Santa Claus comes ev'ry day down his chimmney....😊😊😊
i love the fact that this guy has an entire hardware store in his house + a electronics store
I like the video, at least it's give me an Idea for a budget type of personal interest for making an electric motors. Thanks ha
That thing is soooooooo powerfull⚡️⚡️⚡️⚡️⚡️🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥
You could power a bicycle with this
Sanjay Bajpai a GoKart!
Can not imagine, how much force created this aggregate 😲😲😲
multiple small motors is better than 1 big motor when it comes to operational assurance but there will be more moving parts hence more to maintain. Gearings also consume some power and it require ratchet type gears to compensate less performing or non performing motor which will cause drag
Bhai fabulous work and big fan don't focus on haters comments just focus on ur works and again big fan *plz reply*
It is amazing..
It can be developed to be used in more powered machines in factories.
I think it is good to keep all the gears in closed gear box to avoid corrosion and to decrease the noise.
What an idea sir ji 👍👍👍👍👍
I really like these things ✌️
Thank you ❤️
你这个老六居然掌握了小米手机核心技术“堆料”。🤩
Will you actually use this "thing" for a vehicle?
@MUM!N maybe with the right gearing... never know
@MUM!N should be around 150w per motor. 900w total.
The benefit of the motors is they take the load off of one another more than adding speed. The best use of this thing is for applications that need a ton of torque, like drills.
The array of gears to get this thing ready for a vehicle would require a transmission, so yeah it could be done, but the top speed wouldn't be what you'd expect. It would get to top speed pretty quick though.
This engine that has it has a strong torque believe me can be used in the bike and also in the Go Kart
i like a boat
Good luck ❤️👍
You hit those electric motors with no mercy those bearings are not going to last very long! 😅🤣
This can be use as generator 1 input motor 5 output energy... good project...well done
Not efficient. 1 motor will work hard.
are u dumb lmfao
You need to add wheels to the project so it make sense!
Make a toy car with this engine.i will de awesome 🔥🔥
I'd like to see the power of it!
មទរ័និងមួយមាណ
Good work 👍
Question, why not use 1 single gear and put in circle all 6 motors?, great video 🤠
Because it wouldn't be a V6.
Please make a car from this powerful engine I wanna see it😮
A rule in motors :don't put two or more motor on the same axie they well broke each other
Plz elaborate
They might broke each other if they are not loaded but let's say , every single motor has same amount of coil lenght inside so they can't broke each other but if some motor has 1 extra turn than others , this single motor can likely burn out because it spins a bit faster and pulls other motors to achieve maximum speed of that one motor but it will take a long time to burn one single motor with 1 extra turn
OMG *Break people.
I believe one of the motors could easily charge the battery and thereby giving you unlimited power supply!
I get here you’re coming from. Wiring 6 DC motors in parallel to drive the same shaft like that, all 6 motors must have exactly the same impedance across the windings, exactly the same field strength in the magnets, and exactly the same RPM. If just one motor is the tiniest bit out of spec from the rest, it’s going to either drag or be dragged by the others, which will cause it to overheat and burn out quickly. A way to make this work well would be to have electronic speed controllers on each motor so they can all be synced up.
Set up right, this would be a good way to get a big load of torque from small cheap motors!
Хорошая идея для автомобиля.
Yup, now that engine can power a lot of items, I'm thinking irrigation water pump on a farm and stuff #cool
same here.....sorry to see this video after a year...it should have come to my recommendation earlier
Мужик не заморачивается. За хреначил вал в шестерни молотком "на холодную" и доволен🙂👍
Так а смысл заморачиваться, если практического применения никакого у такой поделки нет. Если нужно больше мощности, нужно взять другой мотор, не будет потерь на трение и грохота шестерней.
nice work...
This would be a perfect engine for a toy car with Gears and a workable clutch
Great machine..👍👍
This by motor I can use it in gokart .My son and I can walk very quickly. I weigh 94 kilograms and my son weighs 20 kilograms
UnknownPerson true
@UnknownPerson Gas wastes so much gas...
@@hennarkilsen1389 if you run at full throttle for countless hours you can then make it through half a tank
This actually not that fast it just has a lot of torque
Fully satisfying 😌
you might use it as a high power generator
if you power 1 motor and connect all the other 5 in parallel, you can have 5 times the output current from the 5 motors
if you power 1 motor with 12 volts 1 Amp (assuming the motors run on 12 volts 1 Amp), you would 'theoritically' have 12 volts 5 Amps on the paralleled output at no load
and by using an SMPS, you can step the voltage up with the boost converter or step it down with the buck converter, this way you can have a powerful generator made by you and don't have to rely on free energy devices to help you (Note : free energy doesn't exist)
so you offer to connect generator to the motor which is connected to the grid?
Smart idea
Esta bueno el video entretenido. Pero y la uña pa cuando.
Com um maquinario desse TBM, faço até um foguete 🚀 pra plutão, top demais 😍 🥰 🤪 🤪
man surely it has insane torque.
if you freeze the shaft and heat the larger gears before assembly you can gain tighter tolerances
I Appreciate your hard work😍.Bro,it can work as a generator by reverse operation,
Add some diodes and switches so you can control each one and stay one regenerating and count up as you want to stop
Nice how many hp
Обалдеть! Я думал я один до такой штуки догадался. А тут во оно чё))))
@@ruchey Тут ещё и охлаждение нужно. Иначе "стуканёт движок"))
Nice video! Lots of efforts! But lots of losses in such designs. As motors design is not perfect there will be minor difference in speed of each motor. As if some motor lag or leads gears will wear out pretty quickly. Also if motor is loaded with some torque these losses will change dynamically as load will not distribute equally over the shaft length and as motors are also not perfect. Also as motors are inductive loads and connected in parallel configurations current and back emf spikes will spoil the whole design. I just wanted to tell the science behind it. That's it. Else cool work man!!!! Thanks keep it up
すごいし、これからも頑張ってください！
10:14 the proof that there's no free energy!
No one said "free energy".
@@politecat3299 of course not.. Not in this video! The machine tho is very alike some free energy devices you find anywhere in youtube.
bring in THE RECTIFIER
Love it. Would be great on a bicycle.....
Pointless; yes. But a fun waste of time it was, carry on friend.
@@mecheng84 yeah but why not place them right in the wheels, not build a whole engine like all other EVs
Its not a waste of time, its pure youtube money...
Your mind are true point less : p
o l o
I was hoping he showed how much torque that thing has. Without that, the video was pointless
I think it not waste of time, you can use this in making a electric bike because it has high torque
This is future v6 v8 😂😂
Would have been better if you could switch those motors individually depending on your load requirement
That way you would save precious juice from the battery
atleast he's smart enough to know that it's still a motor considered since it's still electric powered. A motor is electric and an engine is gas powered.
Good.
Next, current control(eg；PWM or PAM) is needed for keeping inrush current small.
Nice 👍🏻👍🏻 🇮🇳 || Kuki 31|01|2022
Excellent!! Only the connection rule would be missing, in a switch the change of serial connection to parallel, more speed or more force.
it is already more speed 7k rpm is too much i feel.....more force is key....that will give it many applications...
This is most powerful electric RC engine
Super video, I have a question: what is the current consumption of the motors when idling?
The answer is it will spin on the same rpm. Bcz all the 6 moters are spinning on same rpm so the output rpm will be same. Rpm meanz rounds per minute
Arslan Khan Durrani it’s electric it doesn’t idle r/wooooooooooosh
@@vladimirvladimirovichputin1352 haha yeah so dum
@@vladimirvladimirovichputin1352 maybe aply a little bit of voltage so that it spins slowly
@@vladimirvladimirovichputin1352 r/ihavereddit
Now that was freaking amazing. Top Mark's man.
My mind keeps thinking about the Back EMF being produced here.
Absolutely agree, this configuration is VERY but VERY inefficient, on any side you see it has no practical uses, just as a curiosity, this configuration is used in combustion engines because it is the most practical configuration that can be used in these engines can
Suggest any other efficient methods
Great idea can make a monster truck with it
Втулки медные заколотил на весу(без опроры вала на твердь), рискуя сбить с посадочного места вал на якоре. Скорее всего так и произошло!
Молодец заметил. Я тоже это заметил. На горячую надо сожрать так при нагрузках больше шансов что не сорвёт с посадочных мест либо шпонить.
@@ИванИванов-ф6ю7к 👍 😁 Шпонить не представляется возможным, мал размер, да и лишнее это, при таких задачах. А вот "сожрать" на горячую будет самое то, этого достаточно. Есть ещё один серьёзный косяк, про это тоже никто не пишет : При посадке шестерни на вал двигла,(задаю загадку) -- Куда упрётся(где опора/твердь?) медная втулка? И чем это чревато?
@all video не смешно, зря стараешься
The most powerful hand made electric engine
Make an electric cycle with it
An electric
He did
Speed of presentation is good no draging of time
By supplying power to one motor, will it be able to generate power from other motors??😊
Yo that would actually be really cool! A motor with a high torque potential with all 6 sub motors engaged, but a more efficient motor at low torque with only 1 or 2 engaged
Superb u can make a go kart with it
Vim mais rápido que político brasileiro desviando dinheiro de hospital.
Kkkkkkk mano isso aí ficou muito top viu, vou fazer igual
Is main separate ek moter badha dety to 6 moter ki power use karne ki milti aisa lagta hain muze video bahut ascha laga
Вопрос: а зачем он нужен?
Низачем. Просто трата сил, времени и ресурсов планеты. К сожалению нет закона что бы за такое наказывать.
ei hai начинается уже
Very cool yet completely pointless. Nice job. 👍
this needs to go on a skateboard (-'
👍 جيد جدا احسنت🌹
I would rather say this engine was professionally configured.
I won't imagine doing this at home tho🙄😑
I don't know if that pinky Nail is for coke or buggers but which ever he still got my respect.
6 Motors output connected together in shape of V. Like the hardware but Where is V6 ? It would be useful if the use and advantages are described.
Need one for my electric bike after knowing the actual power.
Guys we can't even imagine the torque 🔥🔥🔥🔥
Yeah since the bevel gears are tripled from small-big order
It can pull a whole van with Nicocado
I think, you can make a generator from this. Just give energy to one motor and take energy from 5 motor.
Am I wrong?
It will give you less energy
@Isaac Eda in additions, any energy can't 100% to work, must waste when working, more or less
Yeah you're right specially if you add a gearbox it would be better.
Nice
No no you can. Easier way is with power strip, all you gotta do is plug it into itself after its been plugged into the wall for 5 minutes and infinite energy!
Great work 😍😍😍
"Drone "
"Drone "
"Drone "
"Drone "
way to Heavy
@Tushar Kashyap converted cow worshipper
so nice keep it up
No I think it’s too heavy and you only need one 775 motor, because it’s very strong
Bruh there’s no way this thing can fly