This Saved Me $1200 || Making a Large Concrete Planter
HTML-код
- Опубликовано: 7 май 2023
- To start comparing quotes and simplify insurance-buying, check out Policygenius: policygenius.com/bourbonmoth. Thanks to Policygenius for sponsoring this video!
Plans & Merchandise: www.bourbonmoth.com
Patreon Page: / bourbonmothwoodworking
Cameo: www.cameo.com/bourbonmoth
Instagram: / bourbonmoth
Links below to tools and supplies:
3M Cubitron Sandpaper: lddy.no/1hset
Spec Ops Hammer: amzn.to/3fMjAOd
Spec Ops Tape Measure: amzn.to/3w1M788
Spec Ops Pry Bar: amzn.to/2Ro3iC2
Spec Ops Chisels: amzn.to/3ga8kKv
Spec Ops Screw Drivers: amzn.to/3ciV8ls
Spec ops utility Knife: amzn.to/3g5ysWZ
Rockler setup blocks: www.rockler.com/rockler-delux...
Rockler Screw Clamps: www.rockler.com/wooden-handsc...
Rockler Bench Cookies: www.rockler.com/shop?w=bench+...
Double Sided Tape: amzn.to/3SumVT7
Eye Protection: amzn.to/3gIO4A5
Corner Templates: amzn.to/3Aj3tS3
Nicks Handmade Boots: bit.ly/3vZ8uMR
ISOtunes Bluetooth Hearing Protection (10% off code- BOURBONMOTH10) bit.ly/BourbonMoth10
Bits & Bits Precision Cutting Tools (10% off code- BOURBONBITS)
bitsbits.com/ref/6220/
Flush Trim Bit: bitsbits.com/product/udft5152...
RZ Mask (15% off code: BOURBONMOTH15)
www.awin1.com/cread.php?awinmi...
Total Boat Epoxy: totalboat.com/bourbonmothwoodw...
Firm Grip Work Gloves: thd.co/3LEO5TE
Grizzly Tools:
Table Saw: amzn.to/3q8Wbu6
Jointer: amzn.to/3gFHE6a
Planer: amzn.to/3xCzH7r
Dust Collector: amzn.to/35AFEWw
Air Filtration: amzn.to/3zyXXsK
Band Saw: amzn.to/3gEtCAm
Drill Press: amzn.to/3xvhxEh
Lathe: amzn.to/3vChWUb 
Хобби
To start comparing quotes and simplify insurance-buying, check out Policygenius: policygenius.com/bourbonmoth. Thanks to Policygenius for sponsoring this video!
11:01 when did you ad BenGay before the sprinkling Portland & is it essential for strength or just old worker recovery?
20:33 I didn’t watch what you did yet. I can tell you idea you did not have: pour pound of granulated sugar on back of pot, put plastic dome over back of pot and had few shovels full of ant colonies w/queen). Add a little water up top under dome for drink and those workers will work for free all night moving sand up to dome to protect queen. Hollow of sand below in 2-3 days more. Can also raise perceived water table by spraying water at inverted rim. Only do that if your free ant workers are not moving sand fast enough. I have not figured out enough ways to further delay completing a project so I would have run a cable conduit tube from dome over inverted new pot to my pickup so ants move it there themselves. Maybe 5-6 days of waiting if keep truck parked close to new pot. Of course, won’t be able to drive truck so it will delay a bunch of other projects….mega bonus!!
21:04 one other idea based on your shim technique - you could also reduce room temp of garage below freezing and pour water into inverted pot. After freezing, it should be lifted or broken.
23:16 clearly I have followed every detail of this saga. The pauses to comment are making it like a mini series on Netflix. Anyway. tip #-12 put pot board on scrap pallet. It makes it easier attach ropes to each corner and have neighborhood kids drag it around to where you want it. If neighborhood kids big & fast enough, they might make it to kids sandbox to drop load of sand falling out bottom. Anyway, tip #-13 unless you live at North or South Poles, there is a time of year to pour boat anchor wife project close to where you want it. Same idea as a tree, you don’t plant a see and 20 years later try to move it yourself. Even if you fattened up helper Mo, he couldn’t help you move a 20 year tree. Lord knows that pot is not moving for +30 years…so cast it where we want it become a permanent fixture of landscape for centuries with no roots or watering required (plants inside excluded)
23:47 divorce protection tip #-16 make sure she uses feet to secure dolly movement & what would be negative -$100,000 in value after you crush or sever fingers or break a nail; latter maybe only negative -$20,000 but only if no blood or skin scratches.
Thank you. My wife just asked me if I can make a concrete planter. With 100% certainty I can now say, "Hell no!"
What? Have something better to do 😂?
Lol that’s funny 😂
That will be on the Honey-do list for ever. You May as well go out and buy one tomorrow.
Lol
Yep, this is one time I'll just go out and buy a clay pot. I have a concrete patio table and benches that came with the house cause they're too heavy to move until I work up the will to bust it up. Great video tho, and I admire your fortitude!
You can make the whole inside of the planter with foam. You just make it in sections with a center peice that you can pull out after it dries that will unlock the foam and be reusable.
Never have i enjoyed a craft video sooo much. I spat coffee across me living room more than once.I subscribed because of how human you are.
Awesome book that gives you step-by-step photos ruclips.net/user/postUgkxTNB_zFBSnTo_O1PqfVUwgi7ityw0JlKt and directions to make every day project. I can see myself making a few of these projects and giving them as housewarming and holiday gifts!
From Wikipedia: "The term "wheelbarrow" is made of two words: "wheel" and "barrow." "Barrow" is a derivation of the Old English "barew" which was a device used for carrying loads."
The term is definitely "wheelbarrow", but it is a common mistake to call it a "wheelbarrel", kinda like people mistakenly say "heighth" instead of "height". Also worth noting, in his case since it has 4 wheels, it is a cart and not a wheelbarrow. It is even labeled as a cart on the side.
Thank you, that's neat to know.
@@Beef4Dinner22Yes, that was a cart not a wheelbarrow. And BTW, poting soil is compost, not dirt. As same with concrete, concrete is concrete, not dirt... 😅
The term "wheelbarrel" is an eggcorn. Which is when a word is or phrase has a commonly used variattion in a way that either makes sense in a literal understanding that sounds similar. Other examples are 'old timer's' instead of alzheimers or 'youth in asia' instead of euthanasia.
In my time as a general contractor I’ve poured over 200,000 yards of concrete . But your excursion into that world was the most entertaining, funniest piece of concrete work I’ve ever seen. I couldn’t stop laughing. I’m sending you my hospital bill for giving me a hernia from the side splitting humor! You did it, well done! 👏👏👏👏
I know right! it was so funny how pathetic they are! Your soo right!!!
I'll bet u don't do this again...at least I wouldn't
Best entertainment I had all night :)
What changes would you recommend to make a better or easier end product? Aside from pilling the center of the sand core with something other than sand.
From my math that lines out to about 18-20 years of full time labor, with somewhere between no weeks off and only one week off per year aside from weekends. With an average yearly labor of 2040 hours. How far off am I? That's a long time man!
Monday night, after a shift at the hospital and I laughed until I cried! Great job!
As someone who has moved a lot of pianos, when using a dolly, angle it up underneath the heavy object at the angle you have the bottom at.
For example, at 25:55, you could’ve put the dolly at about 45° and slid it right up under the planter. Then you wouldn’t have had to manhandle it on there, it would’ve all just fallen at once. It’ll save your back!
fr this man^ is not lying
Thanks for taking one for the team. I too was targeted by Skynet’s social media algorithm with an attempt to entice me to create my own oversized concrete cereal bowl. I had a shopping list ready in minutes and was a mere weekend away from my own horror story. I owe you one!
🤣
How much did it cost
Live and learn and do stuff. Even if you fail it's worthwhile.
"...If you just pretend like you know what you're doing, sometimes, it works out!"
LOVE IT!
That motto has been driving my every home improvement attempt over the last 20 years! And sometimes, IT WORKS OUT! 🤣
Great job, fellas! Keep 'em coming!
I'm only 4 minutes in, but "flat bottom planters make the rockin world go round" made the entire video worthwhile and enough to make me subscribe. ha! 🤘
Use landscaping fabric between the rocks and the potting soil in the planter. It prevents the rocks from cloging up with soil.
Next step must definitely be a wood fired oven for pizza
I had the same thought!
I have a better idea, combination wood oven with smoker.
Go around the back, throw in you meats and wood chips to smoke your own meat. Then cook a pizza in the front of it whilst you wait.
I thought the same thing
He’s already got the sand for it
don't mention fire.
I can’t be the only one who was stressed about the state of your floor that whole time
The final 1/4 inch should be a sand and cement slurry which then allows the final form to be made with the template...comes out perfectly smooth
I’m so happy to see that I’m not the only one that dives head first into random new projects without any planning whatsoever. It always goes really smoothly, until it doesn’t. That’s when I realize that 5 minutes of planting would have saved 8 hours worth of painful “Oh crap, what do I do now” moments.
Live and learn and do stuff
For future use, if you get a yard of dirt or mulch, fill up the bed of your truck with Buckets and tubs. Then when you get home you just grab a bucket and you dont need to fill up a wheel barrow. huge time saver
That's big brain thinking!
Thanks for posting this experience. Definitly some things learned for when I do it.
I think a few things would help make it easier. As you already mentioned a core if some other material could help support the sand.
The mixes used were not ideal. For stiffening the sand get straight cement powder.
The bulk of the body use mortar mix or do a three form setup, use the stronger concrete mix in the middle layer, and finish it with motar mix. Mortar mix has lime in it, which makes it stickier and holds its shape better. Also it will finish much easier and probably just with the plywood form due to only having sand aggregate.
Pull the rod out once firm as you mentioned.
Three lifting eyes could be placed in the bottom as feet and for an engine hoist or lifting device. Or drill a hole thru the middle of a small bar and put a cable/chain thru it. Fish that thru the hole in the planter and it will cover the hole on pulling it back, allowing you to lift it.
Let it set for at least a week, better two. It has about 70% of the strength after a week. A couple days may only be 50%. It is not drying that makes it strong, in fact the opposite. It is chemical reaction with the water. That bottom edge being wet is good. Wet the rest of it and leave it for several more days.
Use the pile of sand to safely flip it. If lifted on the cable you could tilt and lower it into the sand pile.
Use a form shape that leaves something to grab to lift it later (a lip), and a rounded corner to prevent chipping.
Little late with this but what kind of sand should I be using? I have play sand but it keeps collapsing. Wetting it with water makes it worse. Just trying to get some info to hopefully ween down my frustration level from that damn play sand.
@@JMtheCONQUERERIt's likely washed concrete sand. You probably won't find it by the bag at the home store, but will need to go to a local quarry to get it bulk like he must have in this video.
You just need it to hold its shape though. You could try lots of different things as a binder to get the sand you have to work. Sodium silicate (water glass) from a foundry supply would get real hard quickly, but isn't super cheap. Egg whites, corn syrup, flour and water might work. Anything that firms it up but is water soluble to wash out later.
You could use foam and either sand to shape or hot wire cut it. Then use a much thinner filler like Bondo. Clay would work very well as long as you don't let it dry and crack.
Or make a permanent mold with fiberglass, wax it, and cover it with fabric strips to give the concrete something to stick to.
You could buy a commercially made plastic one, and use that as the inside in a similar fashion as above.
There are really so many ways this could be done.
If you do this, use acrylic additives to the concrete, it'll make it weather and water resistant. It willl be less likely to decay or have freezing issues. Cost a little more but will last a lot longer. It will also give it a nicer finish.
Something that would have made leveling the bottom a tad easier would be to do what potters do for mugs and bowls and just make a slightly rimmed base, i.e., creating your plywood form to make a slight concave on the center of the concrete. That way the entire bottom doesn't need to be flat and the bowl is more stable and saves you some effort.
Those dips! Yes!
Rimmed... lol.
You mean like a small ring at the bottom? @@asvarien
Plus, it would help with the drainage 😜
The "Treehouse" is looking good. Time we saw some more of it's making! 👍
I’d love to see a follow up video in a year or so showing how this has held up.
Without steel wire inside? I don't think so
As long as it stays put that thing will be solid for 100 years.
@@lglge611 Surely the fiberglass serves a similar role.
Maybe in the US with the seasons changing it does not last long. But here in the Caribbean with hot weather year round it goes for years.
@@lglge611 Steel is only used to provide lateral strength. Concrete is extremely strong when it comes to compression strength. Steel wouldn't do anything. This concrete planter should last a lifetime.
I am so happy to see that I am not the only that will go out of my way to find the hardest way to do something. Great video !!
The fiberglass tape was a great idea. I bet one strip around the rim would add even more strength
I would suggest you use wedges under the plywood with blocks stepping it up till you can get a floor jack under it and tip it into a truck tire for it to flip into.
A toe jack would be ideal, it'd only have to be lifted an inch or so to slide it under
Jason it is WheelBarrow, don't you just love it when you surprise yourself and something works and looks good when you're through. Well done Jason and wife and Craig.
I love the spirit of experimentation associated with this and your “let’s give it a go” attitude. Fun vid to watch.
Ok, so the entrance alone earned my subscription!
I've been told that this is called sweep moulding. Normally a thin piece of metal is attached to the wood, and protrudes out to define the shape. Also towards the end a slurry is made to give it a smoother finish. A similar technique is used with a profile to make plaster moulding.
My mother always told me never ask someone to do anything you’re not willing to do yourself unless they do it for a living. I commend you. I’ve dreamed of making something like this. I can see it’s every bit as difficult to make these as i suspected. I’d never have the audacity to ask my husband to make one. I do thank you for showing so much detail. Sadly, that dream just died for me tonight....but it sure was fun watching you succeed. It turned out beautifully. I know you must be very proud.
We’ll worry about that later is my mantra for every DIY too 😂
Also, the face of the circumference cutting rig should be a wedge instead of a flat 90 degree edge. That will naturally force the sand to compact through the slit rather than constantly trying to re-add fallen sand and work around the fact it can just cut off a chunk of the entire sand hemisphere randomly.
😂😂😂
Good tip
Good thinking
Thanks Jason. I was expecting a disaster at every step of the construction. You kept the suspense level of your voice just right. The finish when you put it on the porch and I saw the moss growing there on the concrete was very nostalgic for me. We lived in Albany for 18 years and had that same feature on our porch!
We even had moss growing on the asphalt in the street.
literally snorted milk a few times watching this. BIG fan of creating the inner form in styrofoam! Glue insulation sheets together and rough carve the form then go in with sand to refine it. GREAT vid, great planter 💯
This is a genius idea. I'm stealing it immediately!
@@1TornMonkey Yeah, lmk it after you price the difference.
PSA Just so everyone knows: rocks at the bottom of a planter DECREASES drainage. In between the rocks fills up with soil anyway and rocks are impermeable to water. So what you're doing is creating a LESS permeable layer at the bottom of your planter. That decreases the speed that water can drain out of the planter. Planter looks great!
THANK YOU! It makes me cringe everytime I see someone say, "just put rocks in the bottom. " NO DUDE! DON'T!
The gravel gives a place for a water resivoir and keeps the dirt from clogging the drain holes.
If you don’t think that’s the case then you should call up the American Concrete Institute and the Department of Tranportation and let them know they’ve built every concrete road in history incorrectly.
I'll call up the concrete company and ask where they grew their concrete plants.
Just a tip. Before applying concrete and forming after making sand mold, brush the wood where concrete will meet wood with oil.
The wet perimeter isn't bad... cement cures by being wet... you don't need to get the wetness out.. in fact you should add some to make the planter stronger.. it can still cure after a week or two and water helps..
The full cure process (chemical reaction not drying) for Concrete takes a month. Pros apply a curing compound when it’s wet to lock in the moisture. The plastic is a cheap diy alternative but really should be left on for 3-7 days.
You also could apply a sealer to reduce the porosity, especially if you get freezing weather.
That flip was such a crazy (dumb) move. Could’ve lost it easily. All that work, time, money, gone in an instant. Glad it worked out and it came out nice.
Amazingly GORGEOUS!!!! Shout out to Mrs. Bourbonmoth for that perfect plant arrangement for the mega planter! It looks so natural and earthy. 😇😊
You can make lighter-weight ones by putting peat moss or coconut coir and pearlite or vermiculite into the cement, which is usually called hypertufa. This is also better for your plants because it is semi-porous.
Wouldn't that make it more susceptible to winter freezing damage? Only good for southern climates or could you seal the surface to keep the light weight benefits?
More expensive and hyper tuna takes a lot more time to cure. Usual recipe is 1\3 cement, 1\3 perlite,1\3 spaghum moss.
@petroart you can seal it, and also add drainage holes to keep water from soaking through and staying in it. Using a sealant meant for ponds will prevent anything toxic from harming your plants. This should help it better withstand freeze thaw cycles in colder climates.
With so many other videos explaining different principles to achieve this same process, I still appreciate the “let’s just figure it out on the go”
Reminds me of many projects I’ve attempted. Sometimes that’s the best way to tackle something. Well done
Some broken color glass design on the cement planter would have been more fun
It’s a “wheelbarrow “ unless I’ve slipped into another reality. I so enjoyed this video😊😊😊
You could've also used PVA glue as a binder in the sand to make it stick together more (That's what professional sand castle builders do)
It's wheelbarrow, because when excavating the material removed is called barrow, hence the tool used to move the barrow is a wheelbarrow.
Neat
I thought it was barrel, but thanks for the correction.
.......... While I was thinking about it, you were actually doing it. But then my 50 feet by 300 feet densely planted vegetable garden and canning everything from it possible, absorbed a lot of my time this past summer here in Ohio.
This was your funniest video ever. I loved it! 😂
Looks awesome! Only thing I would have added would be some indentions from the drainage hole to the edges so water has an easier way to escape from underneath the pot.
Yeah, this might induce root rot down the line.
That process looks like a genuine beating. It also makes the concrete planters at Costco a bargain at $49
Until you own one for more than a season and find the break in the winter.
@Court that doesn't happen as much down south. 😊
Costco says "We're sorry. We were not able to find a match."
I highly doubt they include 600 pounds of concrete.
Seems like this would have been the ideal project for "aircrete", concrete mixed with foamed soap which causes it to cure in a manner that is very light and easy to work with, yet strong enough to be usable structurally.
Yep. It's work! This is how bells are made, basically, so there's a lot we can borrow from that traditional trade. As you found, creating a larger permanent structure to take up some of the negative space really helps things along. Styrofoam insulation can be shaped pretty easily, but even something like regular red bricks are very handy - especially when you consider that they're reusable. Stack up the bricks until you have about 3" of gap that you can cover in sand, and then start sweeping to get the final interior shape you want. And if you really want to go for a cool factor, use the old Roman concrete recipe so your planter will get stronger with age and be around thousands of years from now. 😁😎
Where can you find the Roman concrete recipe? I thought it was lost to time...
@@user-jb9tz2om4d Lost... and then found. There's a good video on the details -- ruclips.net/video/nXS1g5HTYJw/видео.html
It comes down to using "unslaked" lime in the concrete mix. The volcanic ash is important, and you can still get it today, I'm sure, but "hot mixing" the concrete so that you get inclusions of unslaked lime allows for the little bits of lime to then fill any cracks when water gets into it. Hence, a very strong concrete that heals itself constantly.
Interestingly, I'm told that we can mimic this today with various chemicals, but choose to not because we're always destroying what we build and there's no reason to add to the costs of construction when you're just going to demolish the building in 50 years.
Use a big plastic planter to take up some of the inside void maybe? Looks amazing! Love it.
Needs to be pretty sturdy any flex will end in disaster DAMHIKT
@@st170ish those moulded plastic ones are sturdy enough for my 225 lbs self to stand on. Not the kind that come free with your outdoor plants. Anyway, I was just spitballing, take care.
@@jonboy8181 there's going to be a lot more than 225 lbs on it, any give it will collapse with a landside.
@@st170ish But then you could just use easy to get field dirt inside of it, instead of clean sand.
I don’t think the form has to support that much weight. The concrete binds to itself, and forms a complete self supporting structure. Presumably the fibreglass/plasticiser additive helps with this binding. When it’s very wet/fresh it obviously needs some support, but this is setting rapidly, so the first layer will probably have some structural strength to support the next layer….maybe. The inside form would have to be porous though, to allow the concrete to dry and cure, so maybe the plastic planter wouldn’t work for that reason.
Concrete cures while wet. Drying stops the process, so the rim will be stronger than the rest.
This is my first time seeing content from this channel. The story telling kept me watching the video to the end. I found it informative, interesting, and humorous. Great job!!!!
Jason, I’ve always had the idea to try this using decreasing circles of rigid insulation. This would give a stepped pyramid when right side up. Then the ridges could be used to hold lumber at various depths and decrease the need for all that soil. It’d also make it quite a bit lighter to construct. Otherwise, awesome planter. It looked beautiful.
I use packing peanuts to fill a part of my planters…its a way to use an otherwise not so useful item and save a landfill. Just don’t use it if you are growing vegetables or things you will eat.
Very smart homie.
Neat idea
Great effort, guys. 👍
But I have a suggestion, please carefully remove the centre plant & tease the roots, as it looks pot-bound to me.
Once it's removed, gently use your fingers to free up the side roots so that they aren't as compacted/matted, then open up the hole, plop the plant back in & replace the potting mix.
I noticed the roots were bound, too
@@jessicaannes Well done. 👍
Also, a tip for people buying pot plants, squeeze the sides. If rigid, there's a good chance it's potbound, so put it back & find one that's softer.
A bonus tip, plant seedlings. They're cheaper & will catch up to the more mature ones quickly.
Without wishing to cause any offence to anyone, it isn't often that an American can make me laugh so much, so well done to you! I thoroughly enjoyed your video.
I had also watched several videos and looked up several pins while redoing my backyard patio and I had purchased most of the materials I thought I would need to make several planters. Boy, oh boy! I am so glad that I watched your video first before I attempt to make them.
Thank you so much!!!
That metal strapping is called Plumbers Tape.
Or strapping iron. I think it depends on where you live
@@FuzzeeDee I lived all over Canada, in the maritime sand Alberta many called it strapping iron. Not so much in Ontario. Of course that was us Electricians naming it, or ‘borrowing it” from the plumbers
I want to power wash your walkway at the end of the video so bad hah. Great job, looks good.
Regarding potted plants from the store, my grandmother taught me to break up roots that have grown in a circle aka "root bound" in a pot before planting potted plants in the ground. Otherwise the roots will continue to grow in a circle and potentially not get enough water for the plant. I'm in the south and our summers are brutal.
That's a great job. And your wife planted that out nicely. Thanks for the video.
This is why you do a 40% perlite 30% sand 30% Portland cement mix. The perlite makes it MUCH lighter. Good video
Flat bottom planters make the Rock’n Roll go round…
Three big mistakes you made, first make up some neat cement(no sand just cement powder and water) and gradually pour it over the sand it'll form a layer about 1/4 thick with the sand on the mould, then dont use concrete mix its why you had so much trouble smoothing it out with the rotary form, use a render mix!
Lastly should had made a few hoops of fencing wire to brace it radially, one hoop in the bottom layer and one near the top so if it does crack(it will one day) it doesnt split open like an smashed chocolate easter egg...
Finally as every gardener should know you need air under your pots 😆
Oh and one or two more things, your pivot pole before applying the cement cut some pvc pipe a few inches long give it a good coating of grease put it over the pole and push it into the sand a bit.
When you demold it'll be a lot easier to remove the pole and the pvc will just slip out.
Also if you're only going to have one drain hole contour the mold so water drains to it, if you want multiple drain holes a bit of pipe makes a great hole punch while the cement is soft still.
You need to seal the concrete pot internally, you can buy spray on I reckon its a PVA product or you can just use some thick paint.
As you may have guessed yeah I've made a few failures before getting the process down pat.
I made it by myself, getting it off the ground , which is where I chose to make it was a bit easier. I dug around it. The lifting off alone had my fiencee and his friends saying , Never Make it again !!!!
28:23 If you close your eyes and just listen, it sounds like you’re REALLY happy about it 😂😅
You need little spacers on the bottom, it won’t drain sitting flat on your step. Great job I’m impressed
He probably could have made little channels in the flat part going from the hole out to the edge.
I was just looking at making one of these. You beat me to it…….you make the mistakes first 😂😂
2:47 "... was that a mistake? Craig doesn't think so." After reading some of the other comments I think I better get popcorn
Thank you for the ride. The drama during the build was worth the watch and had me in stitches and some. I was expecting total disaster... Thank goodness for concrete and it's ability to makeup for our shortcomings.
Nice build which turned out splendid.
Due to the physical properties of water, using filler materials like rocks in the bottom of planters actually hinders drainage and can lead to issues like root rot. You can look up “perched water table” in relation to container/potted plants to see source documentation, but in essence, the change in material leads to the water moving sideways instead of downward, creating a saturated zone much closer to the plant roots than if it was all potting soil. So if your plants die mysteriously, they may have drowned.
Otherwise, a fun build video!
This is true.
Ha I posted the same thing. I didn't expect to see so many plant people here.
Life hack for next time: use packing peanuts as a base layer in your pot, top with mesh, and then add rocks/soil/etc. Keeps things lightweight and manageable (especially if your planter isn't already 600 lbs lol)
Just be sure it's not the kind that dissolves in water
Thank you, great video. Love the commentary/narration, feels like much of the thoughts that go through my head as I'm struggling through a project for which I have no idea what I'm doing🙂
I’ve been subscribed to a couple of Vietnamese cement pot makers who use this technique. One guy builds giant pots, 4 feet tall, 3 feet across. Same technique. Another guy builds smaller bonsai pots and can do hexagon shaped pots. He has a system where the pot rotates on a turntable, and the side wiping thing is on a spring loaded armature that follows a template. When the armature follows the template, the wiper goes in and out to create the hexagon shape. It’s an ingenious homemade system that works incredibly well.
I wonder if doing this upside-down would have been easier. Build a box to hold the sand, and then carve out a bowl. Easier to remove the sand later.
Maybe Craig is playing in the sand because he wants more treehouse content too! Come on Craig, give the boss man a noogie until we get a finished fort! 🤣
This was great! lol. Thank you for actually making this from start to finish. I had been watching the sand pot videos prior to yours. This was as real and honest as it could be lol
Nice build. I think using a bag of fibre reinforcement in the concrete mix, would have much better strength throughout the entire planter.
11:43
You don't use concrete , fine sand mixed with cement is what's used .
No rocks in the mix .
@@44xxggaaj not sure what your point is? Concrete is the result of mixing cement, sand and water
@@eoinosullivan2636 The point is he made it so much more difficult and time consuming that if you wanted to learn how to create your own planters you'll be frustrated with the process and won't come out the a perfect shape and most likely unhappy with the end product because it will look hand tooled and not molded .
He started using hand tools because he couldn't obtain the correct shape and his screed was incorrect you need a sharp thin edge to contact the cement and you can't screed with a blade hitting the rocks that are in concrete because they move as they a hit the wood he was using causing voids and thats why you use sand !
I make plaster , gypsum , cement and high density urethane foam architectural moldings as a profession from screed sleds and rubber molds so I'm aware of the process that achieves the shape and your not gonna get it using concrete !
Thats the difference between someone who knows and someone who doesn't .
@@eoinosullivan2636 Concrete is cement plus aggregate which is larger rock and sand not cement and sand .
Although you have a drainage hole in the bottom, it's unlikely to be effective, you should lift it up on some sort of spacers
Three drainage holes for a pot that size.
@@jessicaannes A little late unless his wife doesn't mind having the pot emptied.
From experience I put in multiple smaller holes with channels for the water to exit without having to use spacers. Personal preference.
@Brian Reddeman Yes, definitely a little too late! The comment was for future reference and/or advice for others that are going make this DIY.
@@brianreddeman951 I dunno, dude is expert on wedges now - maybe they're still lying around in his shop. 🙂
Thanks for the video and your honesty, hilarious stuff. Definitely makes me feel so much better knowing other people are out there winging it just I do so many times.
Just a tip: Put something under the planter to lift it up from the ground so it will drain properly. Or else it might crack in wintertime. Looks awesome though. Great video!
watched another video on this and he did a very wet mixture as the first layer to probably do a shell to protect the sand
Lightweight concrete would have helped this situation. There are various formulations you can find here on YT - ones using perlite, foam made from Suave soap, fiberglass threads and more.
Funny that you posted this. We must have seen the same Insta and both had the same foolish idea that it looked easy.
Mortar no large aggregate. CSA mixes also set up faster and stronger.
I believe the "strappy thing" is called plumbers tape.
That was something!
I've been trying to talk my other half into making a frog pond of fibreglass, and it needs to be bit elevated (not in the ground) so the cane toads don't get in there, only the tree green frogs. The hard part is to make the mould first. Ideas much appreciated!
Nice, too bad you made it so small 😅
It always amazes me how your videos can be around 30 minutes long and still feel short.
The cement topping to the sand totally works, we used to mix Portland into roadcrush for grading prep so that as you mist between your packs on a lift you get maximum proctor.
Awesome planter!👍 Hard work really paid off. Just beautiful.😊
Great, as usual! I noticed the completed treehouse (without any trees😂) in the background of the sponsor's push. As I followed all of the build videos is there a final one to get to where it is now?
Great Question… 🙂 check back soon
Thanks for convincing me…this is a project NOT to add to my “to do list!” Hurray! The list didn’t get longer! 🎉
Note that I haven't finished watching, but normally there is metal attached to the wood. It's the metal that forms the shape.
Só happy you did this myth-buster-thing cause I was ready to make my own planter… now not anymore 😅
I have made 5 concrete planters with varying degrees of success. Hypertufa with peat moss or perlite and Portland cement seem to be the best combinationof weight vs strength. I tried papercrete but the process of shredding all the paper is a real beating.
How did I get here I don’t know-I have no interest in making a planter. But I’m so glad I did, because I’m in stitches. Whoda thunk. I’m also appreciating the ingenuity.
i use plastic wrap on my sand forms. Also a slightly wetter sand helps. Also make life easier for next time. Once the concrete is set up before you remove it, cover it in plastic wrap and hit it with spray foam. Make a mold of it for next time, then you can have matching planters. wooo hooo
16:38 He said "Eat woodchips plant, yeet!"😂
You must pour wet cement let it flow down, if you put it dry it's hard to rotate the form, let it dry in 15 minutes and put stainless/fiber mesh. Then start second layer pour wet cement, not to wet.
I've done 2 concrete projects.... One was a heavy base that I mounted a pipe into so I could have a bike stand for maintenance, which works great and my bike doesn't have any issues hanging from it. The other was intended to be a desktop firepot... I've been too afraid to light a fire in it though for fear of it cracking and leaking burning alcohol all over.
The one thing I wish I had was a concrete form shaker, someday I'll get the one on my Amazon wishlist when I expect to do more concrete projects.