Dear Sir, How can I define material for surf152 element which is generated automatically by assigning convection in the simulation of thermoelectric generator? May I define it through APDL or directly in Ansys.
السلام عليكم بيظهر erorr Your license configuration does not allow pure electric analysis necessary to use with defined material properties. ممكن مساعدة لحل المشكلة
Assalamualaikum sir. I created a design of TEG same like you and exhaust muffler. Can i use you method in the second video (for the block created) to run my analysis? The different is only my exhaust and the block you created.
عاشت ايدك استاذ . اذا عندي فولتيه عالية وامبيريه وحبيت اسلطهه على معدن هل ستتولد حراره ؟ كما في لحام النقطة؟ هل ينفع استخدم thermal-electrical لعمل المحاكاة ؟
Check the published papers for authors "H Khalil" and "H Hassan" or the PhD thesis sold on Amazon by the name "HEAT RECOVERY ENHANCEMENT USING THERMOELECTRIC GENERATORS"
Hi sir, I have a doubt sir, the voltage you are showing at the end of the video (-1706.3 mV) is that the open circuit voltage ? also how to measure the short circuit current?
No, this is not the open circuit voltage. This is not an open circuit. There is a load connected to the TEG. I don't know how to measure short circuit current, and I do not know why something like this is important in measuring performance.
@@H4Isoftwareservices thanks for the reply sir. So if I draw my TEG without the load and measure then it's the open circuit voltage right. Also in some research papers I have seen the graphs between open circuit voltage and short circuit current. Now I understood how to measure the voltage ....but how to measure the current in simulation??
Yes, that's right. If there is no load, this is the open circuit voltage. You can measure current similar to measuring voltage. It is one of the output parameters.
I have a question, I used ANSYS FLUENT, to calculate the temperature distribution at the two TEG sides ,, Now I want to import the FLUENT results to the THERMAL-ELECTRIC and calculate the power that will be harvested from the thermoelectric generator ,,, How I can do this I ask for how to link FLUENT with THERMAL-ELECTRIC,,,, And how to calculate the power generated ?
Check the other video in my channel titled "Simulation of thermoelectric generators cooled by air - Mechanical and Fluent" And check the official ANSYS video titled "ANSYS System Coupling: One-Way Data Transfer"
Hello sir. I am a student and I am trying Steady-state thermal analysis for a TEG. What should I do to calculate the cooling power and hot connection heat dissipation in ANSYS program? Which surfaces are chosen for them or else?
At the end of the video, I am calculating the temperature and voltage distribution. You can find also the heat flux as one of the available parameters. You can use it to calculate the cooling rate at the cold surface of the TEG. You can choose the hot and cold surfaces according to the solders' materials.
thanks brother for this amazing tutorial, Please I have a problem when I click solve the error message showed up is : Your license configuration does not allow pure electric analysis necessary to use with defined material properties. I changed the version And repeated the same process and the problem still showing up. what should I do ?
@@H4Isoftwareservices I see. I tried to add an external resistance to my model but I didn't found the option that give power output as result. How should I measure power output from my model?
@@yintan403 Knowing the resistance l, you can calculate power from eq. V^2/R. Or you can find something called Joule heat, which will give you the same value. That's because power generated is consumed in theform of heat in the resistance.
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
Dear Sir, How can I define material for surf152 element which is generated automatically by assigning convection in the simulation of thermoelectric generator? May I define it through APDL or directly in Ansys.
I do not know this surf152!!
السلام عليكم بيظهر erorr
Your license configuration does not allow pure electric analysis necessary to use with defined material properties.
ممكن مساعدة لحل المشكلة
للأسف مش هعرف أساعد في مشاكل ال License
If I would like to simulate two TEG connected in series, ground voltage should be assign to the end of each TEG or only one TEG?
Only one.
Can you please upload a video of construction of geometry shown in this video?
This was created in Siemens NX. I did not record the creation process.
I will try in the future to repeat the steps again.
@@H4Isoftwareservices please provide geometry...make Siemens nx video
Assalamualaikum sir. I created a design of TEG same like you and exhaust muffler. Can i use you method in the second video (for the block created) to run my analysis? The different is only my exhaust and the block you created.
اخي ما هي ال properties الخاصة ب ال material المستعملة في load ؟
Custom material
الهدف تحقيق المقاومة المطلوبة
تواصل معايا عن طريف الفيسبوك او الواتساب ونقدر نتفق على اجتماع اونلاين صغير نتناقش فيه
Paid meeting
@@Qforyou في وصف الفيديو
عاشت ايدك استاذ . اذا عندي فولتيه عالية وامبيريه وحبيت اسلطهه على معدن هل ستتولد حراره ؟ كما في لحام النقطة؟ هل ينفع استخدم thermal-electrical لعمل المحاكاة ؟
أيوه هتتولد حرارة، بس ما تقدرش تعمل محاكاة لعملية اللحام نفسها
@@H4Isoftwareservices يعني ينفع اعكس العملية اسلط تيار وفولتيه احصل حرارة عند التلامس
؟
@@ahmedovo3011 اه ينفع
Hi, where did you get thermophysical parameters, can you give any reference
Check the published papers for authors "H Khalil" and "H Hassan" or the PhD thesis sold on Amazon by the name "HEAT RECOVERY ENHANCEMENT USING THERMOELECTRIC GENERATORS"
@@H4Isoftwareservices Thank you so much
Hi sir, I have a doubt sir, the voltage you are showing at the end of the video (-1706.3 mV) is that the open circuit voltage ? also how to measure the short circuit current?
No, this is not the open circuit voltage. This is not an open circuit. There is a load connected to the TEG.
I don't know how to measure short circuit current, and I do not know why something like this is important in measuring performance.
@@H4Isoftwareservices thanks for the reply sir. So if I draw my TEG without the load and measure then it's the open circuit voltage right. Also in some research papers I have seen the graphs between open circuit voltage and short circuit current. Now I understood how to measure the voltage ....but how to measure the current in simulation??
Yes, that's right. If there is no load, this is the open circuit voltage.
You can measure current similar to measuring voltage. It is one of the output parameters.
@@H4Isoftwareservices you mean by using the current reaction probe ?
@@sibisri819 yes
I have a question, I used ANSYS FLUENT, to calculate the temperature distribution at the two TEG sides ,, Now I want to import the FLUENT results to the THERMAL-ELECTRIC and calculate the power that will be harvested from the thermoelectric generator ,,, How I can do this
I ask for how to link FLUENT with THERMAL-ELECTRIC,,,,
And how to calculate the power generated ?
Check the other video in my channel titled "Simulation of thermoelectric generators cooled by air - Mechanical and Fluent"
And check the official ANSYS video titled "ANSYS System Coupling: One-Way Data Transfer"
Hello sir. I am a student and I am trying Steady-state thermal analysis for a TEG.
What should I do to calculate the cooling power and hot connection heat dissipation in ANSYS program? Which surfaces are chosen for them or else?
At the end of the video, I am calculating the temperature and voltage distribution. You can find also the heat flux as one of the available parameters. You can use it to calculate the cooling rate at the cold surface of the TEG.
You can choose the hot and cold surfaces according to the solders' materials.
thanks brother for this amazing tutorial,
Please I have a problem when I click solve
the error message showed up is : Your license configuration does not allow pure electric analysis necessary to use with defined material properties.
I changed the version And repeated the same process and the problem still showing up.
what should I do ?
It seems something related to the license. Unfortunately I don't know the solution
@@H4Isoftwareservices can you tell me how did you get the version you were working with please ?
@@Qforyou I get it from the institution I am working with
tec and teg? are they diffrent?
No, the same, different only in boundary conditions
@@H4Isoftwareservices for tec. How can i do a tec what is blunfary cond
السلام عليكم
ممكن اتواصل معاك عندي TEC واحتاج تحليل
وسائل التواصل متاحة على الموقع
@@H4Isoftwareservices
؟؟؟؟ ماعرفت وين تكون
@@عمرمحمد-ظ3ت1ث اقرأ وصف الفيديو
بارك الله فيك
♥❤
Could you help me in making the geometry of the teg with ansys?
I did not create it in ANSYS, I used Siemens NX.
H4I software services thanks a lot for your advice
Can you help me sir , problem solve " an error occurred inside the solver module : general error
Sorry, the problem is not clear for me.
@@H4Isoftwareservices sir, how to mesh (element) connetion?
السلام عليكم
ابعاد teg هل ٤٠ملم *٤٠ملم
او cm
٤ سم في ٤ سم
ممكن لينك للبرنامج او لو متوفر بسعر عند حضراتكم
للأسف غير متاح
يعطيك العافية يا باش مهندس
بس ممكن سوال انا بضيف المواد ووقت افتح قسم الميش ما عم يطلع عندي خيار metareiales شو السبب يا ترى ومشكور سلفا
ابعتلي صورة على صفحة الفيس بوك
سلام
انا اعمل على TEC عكس TEG انتاج البرود في مشروع تصميم ثلاجة مصغرة معتمدا على TEC, ممكن مساعدة في عمل محاكاة هذا مشروع في Ansys
ايه طبيعة المساعدة المطلوبة؟
Sir can you please share Design tutorial
Sorry, but I don't have one
Sir can you share the design file
@@nishanthanbu109
You can buy it. Link in description
يعطيك العافيه يا مهندس
بقدر ادخل تيار للسلك واخذ الحرارة والبرودة من TEC
اه ينفع عادي
طيب بصير اخذ الملف تبعك اللي استخدمتو؟
@@ahmadafifiaa الملفات ليست ملكي، للأسف مش هينفع.
هذا العنصر فيه شبه من خلايا الوقود ايضا نفس الفكرة انود وكاثود وتوليد الطاقة الكهربائية ممكن تعملنا تتوريال على خلايا الوقود؟
للأسف معنديش أي خبرة أو معلومات تخص خلايا الوقود
السلام عليكم
شنو اسم هذا الteg ? في الواقع ارجو الرد وشكرا
ماذا تعني بالاسم؟
@@H4Isoftwareservices اعني هناك قطع تجارية مثلا عندي tec1-12715 الخواص الي مدفوعة على الموقع اني شتريته بس ممكن توضح هذه الخواص ل اي نوع وشكرا ❤
للأسف مش متذكر النوع@@videogame6082
Sir can u plzz upload nx construction video..
Plz
I don't have a video. Only the file.
Is it possible to simulate it without the external wire in model?
If you do so, you will be able to measure only the open circuit voltage. You won't be able to measure the output power.
@@H4Isoftwareservices I see. I tried to add an external resistance to my model but I didn't found the option that give power output as result. How should I measure power output from my model?
@@yintan403 Knowing the resistance l, you can calculate power from eq. V^2/R. Or you can find something called Joule heat, which will give you the same value.
That's because power generated is consumed in theform of heat in the resistance.
@@H4Isoftwareservices I see. I will try it out first. Thanks very much for you reply!
I need the measurement data of the thermocouple. How can I get it ?? a calculation technique or equation?
I don't understand your question. What thermocouple?
@@H4Isoftwareservices Semiconductor pairs in the thermoelectric generator
@@meryemserfirazbilici3427 And what do you mean by measurement data?
@@H4Isoftwareservices I mean, length dimensions to create geometry.
@@H4Isoftwareservices I have another question. Where can I access material data to export to Ansys?
hello sir,
Can you share that imported engineering data file (data.xml)?
It costs 5$.
i will give it for 100 Rs
@@H4Isoftwareservices كيف اشتري وهل يتنم الدفع على ايتونز
@@videogame6082
ادخل على الموقع اللي في وصف الفيديو
Assalam U Alikum Sir
😁
add english subtitle please
I will try
@@H4Isoftwareservices Please sir my project deadline soon, I have to submit it soon, share what you have.
أحتاج إلى ansys
موجود مجانا على الموقع الرسمي نسخة أكاديمية
@@H4Isoftwareservices ممكن URL بتاع sit
@@yasinoupatchika893 الموقع الرسمي
اكتب في جوجل ansys academic
@@H4Isoftwareservices بس مو مجاني
@@yasinoupatchika893 النسخة الخاصة بالطلاب مجانية
ابحث عن ANSYS student او academic
thıs ıs peltier?
Its reverse. Seebeck effect.
@@H4Isoftwareservices how can i do peltier effect ı want to investigate the termal analyze
Same steps, but change the boundary conditions, Instead of measuring the output voltage, assign it as an input voltage.
Sir...how to do transient anlaysis of thermoelectric generator...is there any way?
I do not know