DJI Mavic 2 Remote USB Repair - How To

Поделиться
HTML-код
  • Опубликовано: 13 дек 2024

Комментарии • 53

  • @CWelton6
    @CWelton6 2 года назад +2

    Thank you so much for this great clear and thorough tutorial. I had a bad micro usb port, not broken off, but I think I must have shoved it in bad and messed up the inside part. Bought another daughter board replaced it and all working perfectly again.

    • @elias-jc3zp
      @elias-jc3zp 2 года назад

      where have you found the board?

  • @renatodioses3680
    @renatodioses3680 2 года назад +1

    any purchase link for those ports?

  • @gregparadi
    @gregparadi 2 года назад

    I managed to squeeze one of the wires ( the white one ) when I unplugged the small connnector at the 3:50 . It is so small that I cannot see if the cable is broken or just squeezed. Any ideo how to replace it ( The right one, , red, yellow, black, white wires ) , or what it is anyway ? The RC seems ti be working since then , by the way. Thanks !!

  • @eedeeder6505
    @eedeeder6505 Год назад

    Hi, i am actually repairing a broken remote. Already unsoldered the old socket and wasn't sure if the very right soldering pin is connected to this spot right next to it. Thanks to your video i am sure now that they haven't been connected. So thank you very much for your video, it was a great help. Btw i decided to directly solder a micro usb socket in, since you can't destroy it as easy as the original socket by putting the plug upside down in.

  • @zephyrdrones-charlessterli1026

    Thank you sir! Sterling job!

  • @ixman
    @ixman 11 месяцев назад

    Great info. Thanks!

  • @mohseneghbal6509
    @mohseneghbal6509 3 года назад

    Good job Ian.
    It was a great video instruction.

  • @jeffsav
    @jeffsav 4 года назад

    Mad, also the blue Parts tray?? Great idea.

  • @GaryS-zq6xu
    @GaryS-zq6xu Год назад

    What type of flux do i use a link where to buy would help. Thanks in advance

  • @EmadRashidi
    @EmadRashidi 3 года назад +1

    Hey man, can you please tell me where i can purchase the correct micro port? Mine is completely broken and I want to make sure i have the right part. Thanks

    • @cuteraptor42
      @cuteraptor42 3 года назад +1

      If you have any idea for the solution now, I'm also interested hearing it
      My closest guess is a TE connectivity 2134536-2 , it's not exactly the same but it should fit. I was about to order one to test it

    • @cuteraptor42
      @cuteraptor42 3 года назад

      I can confirm this works, it is really close to the original

  • @djpanther9621
    @djpanther9621 3 года назад

    Good Video-I'm currently attempting to replace the micro USB on a DJI Spark remote....the solder does seem very difficult to melt-is that due to it being lead free??
    Anyway the connector's off, and I'm wondering if I can replace the micro USB AB that was originally on the board with a micro USB B because the design of the AB is such that it's so easy to break the pins if you put the charger lead in the wrong way-I've done it twice!! I don't use the OTG feature at all, so I'm thinking micro usb B should be ok...

  • @psychotraktor
    @psychotraktor 4 года назад

    Thanks for the vid! Do you have any idea where to order a new battery for the RC?

  • @B0M0A0K
    @B0M0A0K 3 года назад

    Great detail and very brave. But I appreciate you doing this so I will know what to do should I have the same problem.

  • @nickpontoski
    @nickpontoski 2 года назад

    So awesome, really helped me a whole lot. Thanks so much!!!

  • @christianfabian8819
    @christianfabian8819 Год назад

    Can you make a tutorial how to repair self draining remotes?

  • @joelmulder
    @joelmulder 3 года назад

    The large USB port on the bottom of the remote’s broken for me.
    Also no idea how it happened.
    If I try to repair it myself, and find out soldering on a new port doesn’t fix it, do you think DJI will refuse to do in-house repairs on it?
    Usually stuff like this voids warranty, but it’s long out of warranty anyways.

  • @Akshaygayakwad_1
    @Akshaygayakwad_1 4 года назад +1

    Sir can you upload video on 2.4 ghz problem and video signal problem

  • @domingosdossantos8241
    @domingosdossantos8241 3 года назад

    Hi, how to fix Controler because Water problem. Thanks

  • @typxxilps
    @typxxilps 4 года назад

    Great job as preparation to add the polish range extender, these 4hawks antennas I ahd purchased for the Mavic 2 ...
    They showed that too but a lot faster. Thanks a lot ... learned a lot from your kind of getting into the things safely.
    Looks like an artist at work watching your style of work, the patience you must have.
    Isn't that a case for the great DJI warranty ?
    Mine is over ... but I am still pretty happy to have bought at least the ZOOM at the right moment in time for 780€ back in Nov. 2018 when they had stress to sell the units due to missing capabilities even after a mighty delayed market introduction for which I had bet and did not buy it. Same for the Mavic 2 fly more kits at below 250€ and the goggles Racing edition cause otherwise DJI stuff is simply too expensive. That way I try to get the stuff, use it carefully and sell it sometime later without much depreciation ... cause it is just a hobby in the end among a lot others.

  • @Barbernz
    @Barbernz 2 года назад

    How do you know if it's the USB port or the battery. My controller won't charge and has a black screen. Basically I don't know if I need to fix the USB or replace the battery.

  • @JensEser
    @JensEser 4 года назад

    Hey Mad, do you know how the repair the Spark? - Mine requires IMU calibration, but always gets stuck in "step 1". Any advise is appreciated.

    • @MadRC
      @MadRC  4 года назад +1

      Sounds like a stuck IMU, when you get stuck can you explain more ?

    • @JensEser
      @JensEser 4 года назад

      @@MadRC It requires IMU calibration. But IMU calibration gets stuck at step 1, and then shows error code-50 message. I refreshed the FW, but it did not help. Do you know how to activate Dev Tools in DJI Assistant 2?

  • @yeshuahamashiaj7234
    @yeshuahamashiaj7234 3 года назад

    Thank you so much

  • @dronezoom
    @dronezoom 2 года назад

    2.4ghz antenna is left or right?

    • @MadRC
      @MadRC  2 года назад

      They are dual band antennas.

  • @jean-pierrelihoreau6533
    @jean-pierrelihoreau6533 2 года назад

    Cudos to you. Thanks for the video!

  • @trosencrantz
    @trosencrantz 4 года назад

    Any idea where I can buy the battery for the M2P controller?

    • @MadRC
      @MadRC  4 года назад

      Sadly that’s not an easy one. Iv not looked my self but Amazon and eBay. If not try to find a pack that similar shape and size at the correct voltage.

  • @omegalord
    @omegalord 3 года назад +2

    Can anyone please show me where the speaker is located? This awful thing needs to be disconnected.

  • @cuteraptor42
    @cuteraptor42 3 года назад

    Do you have any idea of the part number (or an equivalent one) for this usb connector? Mine is completely broken !
    Also the one for the 5d button is missing on my remote so I'm interested into this also

    • @MadRC
      @MadRC  3 года назад

      No this connector is a complete PITA to find. People have replaced it with a micro usb but that will allow charging only.

    • @cuteraptor42
      @cuteraptor42 3 года назад

      @@MadRC I managed to repair my remote with a TE connectivity 2134536-2 it just need a slight bend to find in these holes perfectly
      It's charging and transmitting now

    • @MadRC
      @MadRC  3 года назад

      @@cuteraptor42 that’s a fantastic find. Thanks for sharing.

  • @100SteveB
    @100SteveB 4 года назад

    Nice job! I have had my fair share of broken micro usb port's, mainly on flight controllers. Luckily i am good when it comes to soldering, so have always been ok. Why companies use surface mount usb ports i do not know, through hole ports are virtually impossible to break loose compared to the surface mount ones. Strangely enough i have found that the biggest culprit for breaking ports off the board are the good quality usb leads - the ones that fit in very snugly and have the strong clips that hold the plug securely in the socket. I try to avoid those leads if i can, but having said that, when it comes to flight controllers, there is nothing worse than a lead usb plug that is too loose - especially when your trying to calibrate your mags and accelerators! 😡

  • @johnbapt05
    @johnbapt05 3 года назад

    Thank you some much for the clear way to explain. I had the same issue, starting with lost connection with the phone from time to time. Your tutorial was perfect and avoided $300+ expense !

  • @MrPodgorica01
    @MrPodgorica01 4 года назад

    Hi, i have a problem with mavic 2 pro controller, every time I turn it on message recenter stick error occurred. So, i go to menu and calibrate but it cannot stop on 0% if i just touch stick than i touch it again and it's on 0%.

  • @jeffsav
    @jeffsav 4 года назад

    Mad, Excellent video. Big Fan! I have enjoyed your videos and am a fellow ham and Drone Flyer!
    Was wondering where you got that cool desktop vise assembly. I love that. I am sort of sick of using the Vise devices with suction cups. They never work right. Was wondering if you can share how you did this or where you got it from? Thx, Jeff

    • @MadRC
      @MadRC  4 года назад

      I got it from Amazon, its was a fairly cheap one, try searching for BURNTEC PCB Holder Clamp. What you REALLY want and what I want is this though Sensepeek PCBite Kit , www.telonic.co.uk/Sensepeek-PCBite-Kit-Large-Base-Plate-p/sensepeek4007.htm, this is the best I have seen.

    • @jeffsav
      @jeffsav 4 года назад

      @@MadRC Got it pal, I am looking for it now! Thanks so much! By the way, Great Crystal Sky Videos. I have one because of you. Sure wish DJI would support them.

  • @MrApache64AH
    @MrApache64AH 4 года назад

    Hi Ian, great video, but i was worried that you were not using a Solder fume extractor, be careful this stuff is dangerous.!

    • @MadRC
      @MadRC  4 года назад +1

      Yea I was not actually, it’s something I need to sort. I have a plan for this as I have acquired a few big fans. I may make a video on making it. Been sniffing the lead for years but no it’s not good ;).

    • @typxxilps
      @typxxilps 4 года назад +1

      depends on how often you solder. It's about the amount of exposure as always and even in corona times.
      How often, how long and how close.
      Otherwise world war 2 must have ended far earlier running out of solderers.
      RADAR is far more dangerous ... lot of dead operators died by cancer using american radar equipment in the esrly 80ies

  • @peterhughes2091
    @peterhughes2091 4 года назад

    Thanks for this....touchwood I’m ok so far but I’ve saved the video in case the gremlins visit my remote.
    Take care and catch you later. Peter

  • @ildefonsomoreno6396
    @ildefonsomoreno6396 2 года назад

    Happened to me too

  • @Steve_J
    @Steve_J 4 года назад

    I never could get the hang of fine soldering, mine always looks like I let a child do it. I guess the lines are not my friends LOL 🤷‍♂️. Always like watching someone who knows what they are doing.

  • @revb0
    @revb0 4 года назад

    It seems to me you have had problems with usb before! (Remember Rover)
    Perhaps the problem with usb is 'U'