Check my tracking spreadsheet for current coupons: geni.us/DR101DiscountCodes RunCam Nano: Amazon: geni.us/RunCamNano Gearbest: bit.ly/RunCamNano-GB Banggood: bit.ly/RunCamNano-BG There are 3 sizes to choose from. ET100 - 100mm frame 2 inch props - ruclips.net/video/l3L40QWDbx0/видео.html Banggood: bit.ly/KKET100 (Try Code ToysHo and if that doesn’t work check the spreadsheet) Gearbest: bit.ly/ET100-GB (Use Code KKET100 if you don’t find any coupons in the sheet) Amazon: geni.us/ET100 ET125 - 125mm frame 2.9 inch props Gearbest: bit.ly/ET125-GB (Use Code KKET115 if you don’t find any coupons in the sheet) Banggood: bit.ly/KKET125 (Try Code ToysHo and if that doesn’t work check the spreadsheet) Amazon: geni.us/ET125 ET115 - 115mm frame 2.5 inch props - ruclips.net/video/NpwN68X8ypc/видео.html Gearbest: bit.ly/ET115-GB (Use Code KKET125 if you don’t find any coupons in the sheet) Banggood: bit.ly/KKET115 (Try Code ToysHo and if that doesn’t work check the spreadsheet) Amazon: geni.us/ET115
Great video 😀 I'm definitely going to try the camera mod on my et125. I wonder if you could put a Runcam OSD or similar on it🤔 might be too big a camera at the moment. But in the future, as in the next few months, I bet a small OSD enabled camera will appear on the market.
+Richard Warwick The Micro2 is just a little two big, but yes, I am sure there will be one soon. Will take some reworking of the power to be able to read the voltage though. Or maybe just take this frame and install my own stack? Hmm
DroneRacer101 just remembered Albert Kim did a review about 10 days ago for the FXT T80 nano camera on banggood. It's about the same size and has an OSD, you just connect a wire directly to the battery positive and your away 😀 even connects up to a Runcam joystick to control settings
Nice video. There is no need to remove the pin (ESC 1) between the ESC board & FC. I do it on my first ET100. But on my KingKong ET125 and FPV EGG I soldered only a wire from M1 to PPM. And it works fine with DSHOT600. My videos in english? Yes, no problem. Turn on the subtitle and switch the subtitle from German to automatic translation to english language. Very nice function from RUclips.
Kopterheld FPV Racing so no need to take the stack apart! Just take a wire and bridge m1 and ppm - followed by the resource mapping and the esc update?
That’s correct. I updated it when I did the ET125 update. Waterproof a drone, ET125 DSHOT, FXT T80 Camera Review, FPV Gloves. There is a LOT going on here ruclips.net/video/g-TYJc0UUTE/видео.html
I already have the 125, and the 100 should be here any day. Can't wait. Brushed quads are almost dead, I have several brushed models just sitting , and probably will never get used again. Great vid!!!
Hi, just to let you know (if you don't already) that, as of Betaflight 3.3.0, the DShot mod is no longer necessary for this board. No soldering needed, no resource remapping needed, DShot just works. If you could put that in the description or pin it to let people know, that would be great.
Yeah I was surprised as well but apparently the Betaflight guys built a firmware fix into the FF_PIKOBLX hex file, to make DShot work. Just be aware though, if after you install BF3.3.0, you find that you can't get the SBUS receiver to work, use the CLI command: set serialrx_inverted = OFF
It does work! Upgraded to 3.3.0 and upgraded ESCs to 16.7. No problems, but I did notice the PIDS seemed to be for brushed and were way high. Otherwise, DShot and Turtle mode worked perfect.
Following your video after a long hiatus, looks like FF_PIKOBLX 3.2.2 is gone.. ! Looks like the latest version is FF_PIKOBLX 3.5.7 , I also used the BLHeli configurator on chrome to upgrade the firmware on the four ESCs. I ran into a issue with drivers not working properly when flashing PIKOBLX, I used ImmersionRC's driver fix utility, and a PC reboot later.. it worked. :) Note: I have no idea what your using on the other channel.. I have the 3 default channels on my X9D+, and the turtle flip one that you showed.
The last time I tried that (different video) it was... interesting, but definitely not a valid translation. I guess I could try it again, but thanks to DroneRacer101 I don't need to. That's why I was thanking him.
Fantastic! I have one on the way from banggood after seeing your first video. This is my first brushless. I only have a tiny whoop and some fixed wing to fly.
DroneRacer101 You have the name of one of my first friends I've known for 39 years. Not to make this a sob story but I'm going through medical issues and this made my day when it worked. I did have a friend do the soldering since he has more experience than I do. Thank you again and God Bless You and your family.
thanks so much. I combined a couple of your vids to make this thing perfect (for me) I put in the t80 cam, replaced the stock vtx (mine wasnt working correctly) with the eachine vtx03. this thing is great now.
I lived in Germany for almost 4 years.... I understood that video pretty decent but didnt watch it all. I spent about an hour last night looking at this model pretty hard. I bought too many drones this month but next month I'm considering buying that and just giving it to one of my friends that is Learning acro. He is at that point where he needs more than a brushed micro but not quite ready for a 5 inch. This would be perfect!
I lost one ch in my 4 in 1 one my ET125. I was trying to flash at the time. I am rusty at this hobby. Ordered a whole new stack from Banggood. $ 33 + frt. This video is excellent but I am really missing OSD. So, I will try adding sparrow micro. Working on the new stack, It was interesting soldering the 4-1, it is small. The entire mod turned out well except removal of the pin, I could not extract as described so, I improvised there. I cut it and then insulated it. Not so familiar with ESC protocall as yet. D-600 vrs. one shot, etc., cause it flew really really nice in my house. A blast. The mod went well as shown. Great video. I paused the video a million times, it seems. Sir, If I keep using your ch, I will sign up as I have with others. You should put a link? Nice work and thanks.
Very nice camera solution. (Y) I think my Snapper7 not have so good image. While Snapper was launched about 6 months after your video was made. Quality could go up in that time.
Awesome! - I just ordered the 125 Frame for a build - I cannot wait I think this is awesome for beginners / indoor winter flying. PS - If you have any review items you won't get to - I'd be happy to review them on my channel ;)
I must say a bit overwhelming for me to do my self to get turtle mode , but the camera for sure! Great job there ! they just need to build one with turtle mode and a bit better camera. With OSD ....!....People would flock to purchase it ! just saying. Thank you 👍🏼I'm saving for the ET115 as I write ,maybe for my birth day? KTW.
Whats up sir. First off great video! Got some questions for ya, I just picked up a ET115, and it actually really does fly way better than my tiny whoop by a large margin. Anywho for the questions: 1) What size batteries are you running? (my et came with a sticker that said DO NOT use 3s batteries. Ive found that I like the Tattu 2s 45c 800mah, but was curious if that is enough c. 2) If i make a backup, as well as run dump all from the CLI to save the factory tune that is surprisingly good, can i easily restore them all once upgraded to betaflight 3.2.2 so i dont lose the nice tune? 3) Will turtle mode work if I upgrade to BF 3.2.2 and do not run DSHOT? and secondly did you notice a large difference in flight characteristics for the ET when using DSHOT over Multishot
Good job, my Question I’d for the runcam nano, fist I secured it with a drop of hot glue on the barrel of the camera to make it more secured, Or my question is, are you having blurry image with it? Having some notice it when after crashing, after retrieving the quad I notice that image are blurry, but giving it a few minutes rest, it’s going back to normal.
Off topic question...I bought a multiprotacol module for my QX7 from Banggood and setup the radio following another youtuber vid to bind to eachine E011. Worked perfectly (that never happens ). But I can't seem to get the answer to this question...how do you then change the rate or invoke a flip like OE controller. Any help would be great oh wise one. Lol. Thx.
Best regard I have acquired by ebay, an ET100, I am happy with it. I wanted to update the firmware. the flight controller has a led that shines green, when I install the PIKO firmware, through betaflight, the LED flashes green and then turns off and everything works fine. I have followed internet videos to update with the firmware FF_PIKO and be able to use dshot 600, but when updating the firmware, the led of the flight controller remains blinking green and does not finish working well, since it seems that it does not link in control , despite the fact that the mini receiver XM frsky, links well. I appreciate some solution
In my KK et 115, in air mode, when I arm, one motor start after 0,5s. And when disarm, the same motor stops first. Why? The quad is new and it flies well.
ET125 have a question for beginners how do I slow down the throttle it wants to lift off like a rocket I am a beginner any suggestions Could I use a bigger battery 2s More MAH 1000 Maybe a 65 g battery weight
I just received the ET115, when I arm the motors, they start spinning and everything seems fine, but as soon as I give some throttle, and the quadcopter lifts, it starts beeping. Is that normal? What is that beeping for?There is hardly any instructions in the manual and I am a noob. Any idea?
How do you flash the FC I can see everything in Beta Flight and download the appropriate firmware but it will not flash?? Do I need to do something to the FC? Thanks
I used to. But I have found they change just enough between versions that something is off. So I have found it better to redo it. They always rename one variable or another then when it doesn’t work I have to go figure it out. One one exception is LED. I do a Diff and will copy that back. But this model doesn’t have them.
Hi DR. Quick question for you. With no mods, my motor 1 and motor 4 do not spin with dshot 600. Do you think if I resource motor 4 with the LED, that would work? Motor one works fine with PPM, but motor 4 is still dead is what I'm trying to say..
DroneRacer101. I went on and tried it. I ended up resourcing M1 to ppm and M4 to led_strip. All 4 motors work great on Dshot600 now. Thanks to you and Kopter for these vids. Learned a bunch!
Hello, I wanted to try this mod, but i am facing a probleme and maybe you can help. I have my receiver fsRx2a (www.banggood.com/2_4G-Compatible-FS-RX2A-Pro-Receiver-for-FS-I6-FS-I6X-FS-I6S-FS-TM8-FS-TM10-FS-I10-Transmitter-p-1145881.html?rmmds=search&cur_warehouse=CN) and it is connect in ppm. The receiver can also transmit to sbus, so i wired it from sbus to the r3 of the pikoblx board, but the board is still working in ppm for some reason (the led on the board saying 'sbus or ppm' still light under ppm) the result is my receiver still bind but seem to not send any signal to the flight controller. How can i force/switch the piko blx to use sbus on the R3 and switch from ppm to sbus??
@@SimRacer101 Thanks pal I'm on with sorting out my serial port to run the flasher in betaflight. Esc are done on dshot600 and only 1 motor atm while I manage to flash the fc 👍 thanks for the fast reply ✌✌✌✌🇬🇧
@@SimRacer101 Any chance you could help me out here? Ive flashed the newest firmware to my et100 and the blhelli dshot600 managed to arm it but only 3 motors like you did but that firmware didn't support flip over after crash so I flashed the 3.3 you did but now the tx won't show in betaflight? Its binding according to the lights But nothing showing on reciver tab on betaflight config?
Yea. Check out my update for an easier mod and a cam with OSD. Waterproof a drone, ET125 DSHOT, FXT T80 Camera Review, FPV Gloves. There is a LOT going on here ruclips.net/video/g-TYJc0UUTE/видео.html
Hello, have you seen that you can change the tone of the brushless ESCs? Here is a link to a video showing how: ruclips.net/video/CZxJLAYIlOo/видео.html Would you be willing to test it for us? I was thinking this can be for the ET100. Thank you.
With all the newbies that watch this type of channel why would you recommend as a good drone after you have to change the camera, change the wiring and destroy the looks by hacking up the canopy? There are plenty of good drones that don't need any work in this price range. Be careful of leading people the wrong way
Because right now even with the required changes the ET100 is by far the best in class in the indoor micro brushless category. Did you see the initial review? KingKong ET100 Brushless Indoor Racing Drone, Almost the perfect winter indoor racer. ruclips.net/video/l3L40QWDbx0/видео.html I have SMASHED this thing as hard as I could and didn’t even bend a prop. And it’s wonderful to fly indoor at high speeds. It is by far my pick for indoor flier, even stock. But once you have it of course you want more. It’s what we do.
Check my tracking spreadsheet for current coupons: geni.us/DR101DiscountCodes
RunCam Nano:
Amazon: geni.us/RunCamNano
Gearbest: bit.ly/RunCamNano-GB
Banggood: bit.ly/RunCamNano-BG
There are 3 sizes to choose from.
ET100 - 100mm frame 2 inch props - ruclips.net/video/l3L40QWDbx0/видео.html
Banggood: bit.ly/KKET100 (Try Code ToysHo and if that doesn’t work check the spreadsheet)
Gearbest: bit.ly/ET100-GB (Use Code KKET100 if you don’t find any coupons in the sheet)
Amazon: geni.us/ET100
ET125 - 125mm frame 2.9 inch props
Gearbest: bit.ly/ET125-GB (Use Code KKET115 if you don’t find any coupons in the sheet)
Banggood: bit.ly/KKET125 (Try Code ToysHo and if that doesn’t work check the spreadsheet)
Amazon: geni.us/ET125
ET115 - 115mm frame 2.5 inch props - ruclips.net/video/NpwN68X8ypc/видео.html
Gearbest: bit.ly/ET115-GB (Use Code KKET125 if you don’t find any coupons in the sheet)
Banggood: bit.ly/KKET115 (Try Code ToysHo and if that doesn’t work check the spreadsheet)
Amazon: geni.us/ET115
Great video 😀 I'm definitely going to try the camera mod on my et125. I wonder if you could put a Runcam OSD or similar on it🤔 might be too big a camera at the moment. But in the future, as in the next few months, I bet a small OSD enabled camera will appear on the market.
+Darkwing Duck Ich ging für einen Monat nach Deutschland in der Highschool. Ich erinnere mich nicht alles, weil das Bier.
+Richard Warwick The Micro2 is just a little two big, but yes, I am sure there will be one soon. Will take some reworking of the power to be able to read the voltage though. Or maybe just take this frame and install my own stack? Hmm
DroneRacer101 just remembered Albert Kim did a review about 10 days ago for the FXT T80 nano camera on banggood. It's about the same size and has an OSD, you just connect a wire directly to the battery positive and your away 😀 even connects up to a Runcam joystick to control settings
2 hours and the video is already outdated. 🤪
Nice video. There is no need to remove the pin (ESC 1) between the ESC board & FC. I do it on my first ET100. But on my KingKong ET125 and FPV EGG I soldered only a wire from M1 to PPM. And it works fine with DSHOT600.
My videos in english? Yes, no problem. Turn on the subtitle and switch the subtitle from German to automatic translation to english language. Very nice function from RUclips.
Kopterheld FPV Racing so no need to take the stack apart! Just take a wire and bridge m1 and ppm - followed by the resource mapping and the esc update?
That’s correct. I updated it when I did the ET125 update. Waterproof a drone, ET125 DSHOT, FXT T80 Camera Review, FPV Gloves. There is a LOT going on here ruclips.net/video/g-TYJc0UUTE/видео.html
Kopterheld FPV Racing bf 3.3 no mod required for dshot. Make sure to set serial Rx inversion to off for sbus after flashing to 3.3
Great info. I have a ET100 on the way. Soon to be bouncing off of furniture, ceiling and doing turtle flips on the floor...my wife will be overjoyed!!
Someone told me you don't have to do all of this anymore with Betaflight 3.3. I hope to test it tomorrow.
I already have the 125, and the 100 should be here any day. Can't wait. Brushed quads are almost dead, I have several brushed models just sitting , and probably will never get used again. Great vid!!!
Hi, just to let you know (if you don't already) that, as of Betaflight 3.3.0, the DShot mod is no longer necessary for this board. No soldering needed, no resource remapping needed, DShot just works. If you could put that in the description or pin it to let people know, that would be great.
WHAT? Oh, that is cool. I will test that and update it.
Yeah I was surprised as well but apparently the Betaflight guys built a firmware fix into the FF_PIKOBLX hex file, to make DShot work. Just be aware though, if after you install BF3.3.0, you find that you can't get the SBUS receiver to work, use the CLI command: set serialrx_inverted = OFF
It does work! Upgraded to 3.3.0 and upgraded ESCs to 16.7. No problems, but I did notice the PIDS seemed to be for brushed and were way high. Otherwise, DShot and Turtle mode worked perfect.
Following your video after a long hiatus, looks like FF_PIKOBLX 3.2.2 is gone.. ! Looks like the latest version is FF_PIKOBLX 3.5.7 , I also used the BLHeli configurator on chrome to upgrade the firmware on the four ESCs. I ran into a issue with drivers not working properly when flashing PIKOBLX, I used ImmersionRC's driver fix utility, and a PC reboot later.. it worked. :) Note: I have no idea what your using on the other channel.. I have the 3 default channels on my X9D+, and the turtle flip one that you showed.
Hi which version of betaflight where you using?
Just got mine in yesterday and found that German video... I never studied German so this is very appreciated!
You do not need to studied German. Turn on the subtitle and switch the subtitle from German to automatic translation to english language.
The last time I tried that (different video) it was... interesting, but definitely not a valid translation. I guess I could try it again, but thanks to DroneRacer101 I don't need to. That's why I was thanking him.
Fantastic! I have one on the way from banggood after seeing your first video. This is my first brushless. I only have a tiny whoop and some fixed wing to fly.
Your KingKong LDARC ET100 is really cool now.. awesome!
So cool! That Runcam Nano looked so much better
I had gotten used to the one it comes with, but it is a huge improvement.
I did the turtle mode mod and it worked great. Very detailed instructions. Thank you for this video.
You are very welcome.
DroneRacer101 You have the name of one of my first friends I've known for 39 years. Not to make this a sob story but I'm going through medical issues and this made my day when it worked. I did have a friend do the soldering since he has more experience than I do. Thank you again and God Bless You and your family.
Very nice. My ET115 is on the way, so this video will come in very handy, thanks.
thanks so much. I combined a couple of your vids to make this thing perfect (for me) I put in the t80 cam, replaced the stock vtx (mine wasnt working correctly) with the eachine vtx03. this thing is great now.
I lived in Germany for almost 4 years.... I understood that video pretty decent but didnt watch it all. I spent about an hour last night looking at this model pretty hard. I bought too many drones this month but next month I'm considering buying that and just giving it to one of my friends that is Learning acro. He is at that point where he needs more than a brushed micro but not quite ready for a 5 inch. This would be perfect!
I lost one ch in my 4 in 1 one my ET125. I was trying to flash at the time. I am rusty at this hobby. Ordered a whole new stack from Banggood. $ 33 + frt. This video is excellent but I am really missing OSD. So, I will try adding sparrow micro. Working on the new stack, It was interesting soldering the 4-1, it is small. The entire mod turned out well except removal of the pin, I could not extract as described so, I improvised there. I cut it and then insulated it. Not so familiar with ESC protocall as yet. D-600 vrs. one shot, etc., cause it flew really really nice in my house. A blast. The mod went well as shown. Great video. I paused the video a million times, it seems. Sir, If I keep using your ch, I will sign up as I have with others. You should put a link? Nice work and thanks.
I think the micro is to big, but I just linked another camera in the description I have ordered to try that has an OSD and is NANO sized.
Dir auch guten tag!
I also bought one today
Thanks for the valuable tips ;)
This is actually outdated now. Just update the firmware. You shouldn’t have to do any soldering.
@@SimRacer101 so much the better, if it's that easy: =) ty^^
Turtle mode is such a time saving mode. Prevents the walk of shame 😂
Very nice camera solution. (Y) I think my Snapper7 not have so good image. While Snapper was launched about 6 months after your video was made. Quality could go up in that time.
Awesome! - I just ordered the 125 Frame for a build - I cannot wait I think this is awesome for beginners / indoor winter flying. PS - If you have any review items you won't get to - I'd be happy to review them on my channel ;)
Nice !!!!! I really like that 1!!! Nice upgrade!!!
I must say a bit overwhelming for me to do my self to get turtle mode , but the camera for sure! Great job there ! they just need to build one with turtle mode and a bit better camera. With OSD ....!....People would flock to purchase it ! just saying. Thank you 👍🏼I'm saving for the ET115 as I write ,maybe for my birth day? KTW.
I have heard with Betaflight 3.3 you don’t need to do any wiring any more. DSHOT just works.
Whats up sir. First off great video!
Got some questions for ya, I just picked up a ET115, and it actually really does fly way better than my tiny whoop by a large margin. Anywho for the questions:
1) What size batteries are you running? (my et came with a sticker that said DO NOT use 3s batteries. Ive found that I like the Tattu 2s 45c 800mah, but was curious if that is enough c.
2) If i make a backup, as well as run dump all from the CLI to save the factory tune that is surprisingly good, can i easily restore them all once upgraded to betaflight 3.2.2 so i dont lose the nice tune?
3) Will turtle mode work if I upgrade to BF 3.2.2 and do not run DSHOT? and secondly did you notice a large difference in flight characteristics for the ET when using DSHOT over Multishot
Aw man, this is awesome. What a drone! Now I really want it. HAHA
Does the Flysky version binds with Flysky i6 FS-i6 contoller?
It should.
Thanks so much! Really valuable info.
Thank you for the video! An excellent review!!! Would you recommend a runcam micro on the et100?
I think the micro is just a little to big. The nano is a perfect fit.
Good job, my Question I’d for the runcam nano, fist I secured it with a drop of hot glue on the barrel of the camera to make it more secured, Or my question is, are you having blurry image with it? Having some notice it when after crashing, after retrieving the quad I notice that image are blurry, but giving it a few minutes rest, it’s going back to normal.
Off topic question...I bought a multiprotacol module for my QX7 from Banggood and setup the radio following another youtuber vid to bind to eachine E011. Worked perfectly (that never happens ). But I can't seem to get the answer to this question...how do you then change the rate or invoke a flip like OE controller. Any help would be great oh wise one. Lol. Thx.
Thank you!
Nice work. I recommend a step bit to make that hole cleaner.
I don’t actually want it to be round. I will have another one soon and I really just want it to be wide enough to fit the camera in.
Best regard
I have acquired by ebay, an ET100, I am happy with it. I wanted to update the firmware. the flight controller has a led that shines green, when I install the PIKO firmware, through betaflight, the LED flashes green and then turns off and everything works fine. I have followed internet videos to update with the firmware FF_PIKO and be able to use dshot 600, but when updating the firmware, the led of the flight controller remains blinking green and does not finish working well, since it seems that it does not link in control , despite the fact that the mini receiver XM frsky, links well.
I appreciate some solution
Did this Mod!! Works like a charm.. it does beep the time after flipping?? Is there a fix for this?
In my KK et 115, in air mode, when I arm, one motor start after 0,5s. And when disarm, the same motor stops first. Why? The quad is new and it flies well.
Changing all that is just for turtle mode? Or you get more power
Thank you! Thank You!
ET125
have a question for beginners how do I slow down the throttle it wants to lift off like a rocket I am a beginner any suggestions
Could I use a bigger battery 2s More MAH 1000
Maybe a 65 g battery weight
I just received the ET115, when I arm the motors, they start spinning and everything seems fine, but as soon as I give some throttle, and the quadcopter lifts, it starts beeping. Is that normal? What is that beeping for?There is hardly any instructions in the manual and I am a noob. Any idea?
i want longer flight time et 100/ Does the C rating need to be the same as stock?
excellent details!!! thx
How do you flash the FC I can see everything in Beta Flight and download the appropriate firmware but it will not flash?? Do I need to do something to the FC?
Thanks
Dude, get yourself a hole cutter for r/c car body's, your holes will appreciate it😎
I used an x-acto because I didn’t originally plan on the hole being round. There will be an update before long.
hi, my quetion is, compared with this Runcam the "FXT T80 800TVL cmos" camera is better? (I saw you use it in another vid) thx
I would use the T80 for voltage on the OSD
looks GREAT, works great. ... good job. .. :-)
Cool la vidéo
Thanks Clem. I don’t need to translate that one. :-)
Super cool 👍😎👍
Guten Tag!
When you are updating ur fc wouldn’t it be quicker to dump the cli then copy it into the erased version?
I used to. But I have found they change just enough between versions that something is off. So I have found it better to redo it. They always rename one variable or another then when it doesn’t work I have to go figure it out. One one exception is LED. I do a Diff and will copy that back. But this model doesn’t have them.
Awesome. 👍
Theres a v2 version of this now... can you review?
OH, I hadn’t seen that.
Hi DR. Quick question for you. With no mods, my motor 1 and motor 4 do not spin with dshot 600. Do you think if I resource motor 4 with the LED, that would work? Motor one works fine with PPM, but motor 4 is still dead is what I'm trying to say..
Hmm it sounds like a bad motor or esc unfortunately.
DroneRacer101. I went on and tried it. I ended up resourcing M1 to ppm and M4 to led_strip. All 4 motors work great on Dshot600 now. Thanks to you and Kopter for these vids. Learned a bunch!
That is the first I have heard of that for motor 4. I am going to have to do some research.
yes... i followed each step till I found the same problem... motor 4 doesn't spin... using flyegg 100 by the way
张亮 Resource M4 with the LED pad the same way you did M1. Worked great on my ET100
How about building one for me? I am not good at building or doing beta flite. 65 years young. C'mon Dad!
There are more giveaways coming soon. :-)
I like it looks like you need a circle cut for your drill. lol,
yea, this was just done with an X-acto knife because I wasn't exactly sure what was going to work.
I like turtles. 🐢
Me too. I had two snapping turtles when I was young. They were named He-Man and Skeletor.
Will this work on a king kong fly egg 100?
Yep. Should be exactly the same.
Jesus!!! What did you open that camera hole with, your teeth?!? Lol!!!
Hello, I wanted to try this mod, but i am facing a probleme and maybe you can help. I have my receiver fsRx2a (www.banggood.com/2_4G-Compatible-FS-RX2A-Pro-Receiver-for-FS-I6-FS-I6X-FS-I6S-FS-TM8-FS-TM10-FS-I10-Transmitter-p-1145881.html?rmmds=search&cur_warehouse=CN) and it is connect in ppm. The receiver can also transmit to sbus, so i wired it from sbus to the r3 of the pikoblx board, but the board is still working in ppm for some reason (the led on the board saying 'sbus or ppm' still light under ppm) the result is my receiver still bind but seem to not send any signal to the flight controller. How can i force/switch the piko blx to use sbus on the R3 and switch from ppm to sbus??
Hi there how did you enter boot mode?
I have the ImpulseRC Bootloader installed so it happens automatically. impulserc.com/pages/downloads
@@SimRacer101
Thanks pal I'm on with sorting out my serial port to run the flasher in betaflight. Esc are done on dshot600 and only 1 motor atm while I manage to flash the fc 👍 thanks for the fast reply ✌✌✌✌🇬🇧
@@SimRacer101
Any chance you could help me out here? Ive flashed the newest firmware to my et100 and the blhelli dshot600 managed to arm it but only 3 motors like you did but that firmware didn't support flip over after crash so I flashed the 3.3 you did but now the tx won't show in betaflight? Its binding according to the lights But nothing showing on reciver tab on betaflight config?
What type fc bro?
FF_PIKOBLX
Do you run 3s?
I have not tried it yet, but I think it would be best on the ET115.
Can i add osd?
Yea. Check out my update for an easier mod and a cam with OSD. Waterproof a drone, ET125 DSHOT, FXT T80 Camera Review, FPV Gloves. There is a LOT going on here ruclips.net/video/g-TYJc0UUTE/видео.html
Hello, have you seen that you can change the tone of the brushless ESCs? Here is a link to a video showing how: ruclips.net/video/CZxJLAYIlOo/видео.html
Would you be willing to test it for us? I was thinking this can be for the ET100. Thank you.
With all the newbies that watch this type of channel why would you recommend as a good drone after you have to change the camera, change the wiring and destroy the looks by hacking up the canopy? There are plenty of good drones that don't need any work in this price range. Be careful of leading people the wrong way
Because right now even with the required changes the ET100 is by far the best in class in the indoor micro brushless category. Did you see the initial review? KingKong ET100 Brushless Indoor Racing Drone, Almost the perfect winter indoor racer. ruclips.net/video/l3L40QWDbx0/видео.html I have SMASHED this thing as hard as I could and didn’t even bend a prop. And it’s wonderful to fly indoor at high speeds. It is by far my pick for indoor flier, even stock. But once you have it of course you want more. It’s what we do.
Guten Tag, your german?😂
Nur ein bisschen.