STOP! Watch This Before You Use A Oscillating Multi Tool (Stupid Mistake)
HTML-код
- Опубликовано: 28 сен 2024
- STOP! Watch This Before You Use A Oscillating Multi Tool (Stupid Mistake) In this video we show the #verycoolgang a stupid mistake people make when using their oscillating multi tool and blades. We show you how not too make this stupid mistake and how this can save you money! Let us know who makes your favorite oscillating multi tool in the comments section below.
I feel like most people focus on one spot in the blade making cuts with these. For longer live try to use the entire length of the cutting edge evenly and give the blade q chance to fool down when it starts to heat up. These tips have greatly increased the life of my multi tool blades. Also not pushing it too hard and letting the tool do the work.
Ive heard 2 or 3 people say keeping a cup of water nearby and dunking the blade periodically will extend the cutting life by a lot. Have you tried that before?
No just use the same dull spot and go leave reviews online saying how those blades from that brand suck.
I was hoping you were going to give a grand finale at the end by cutting large bolt! 😆
I feel like everyone was waiting for u to cut the big lag screw lol
I was watching with that same surprise.
I FEEL CHEATED! CHEATED I SAY! WHY AM I YELLING??
If you use the right head you can easily cut a hundred lag heads.
9:15 ... Lies
@@martinliu4938
WTF 👎
I always slow the speed down to cut through metal to reduce heat that ruins the temper of the blade and don't push hard. Let the tool do the work.
Wise and experienced this one is, speak the truth he does.
@@gpjadams2 thanks yoda
I use the fein carbide blade. It was expensive but well worth the price in my opinion. I'm an electrician and mostly use it for metal and drywall. Very impressed.
I've been using a dremel carbide for metal since last year. You can also sharpen most of these blades really easily. I use dremel with the cutting disc. When your teeth are flat cut it straight across then make the teeth then sharpen with the sanding disc.
I've done this but cutting screws off cause u arnt allowed to swing your hammer to breakem off due to location u grab the occilating cut off an boom no teeth when ur at home sharpening is great when ur out an about on the job it's a new one an a new one an a new one lols cause fuckem right
Great tip cobber.👌
Most of the guys I've seen burn out the blade with one NAIL was because they were hulking down on them way too hard instead of letting them cut.
When I got mine the first advice I was given was "it's not a driver. You don't need to push it that hard"
I just made this same “screws vs nails” mistake with a brand new diablo framing blade on a deck demo. Won’t be doing that again.
You can sharpen the dull blade easily, don't throw it away.
If it's missing teeth just file down the old ones and cut new ones with a file or rotary tool
Hell ya !!! Brother Vince sporting the Fein. Good job on the demo of the blade. Must people I introduce Fein to, do not realize what the Fein blade can do. I am long time user of Fein products. Thanks you sir for putting the information out there.
Those blades sure beat the "wood only" POS blades my boss buys by the 100-pack.
im a DIYer, thanks for clearing that up....ive made that mistake thinking screws and nails are like both metal....right !....guess not.......and wondering why the teeth are toast after going through screws, and im blaming the blade lol Love your channel.
Hey Vince, on you guys' recomendation, I got a oscilating multitool, same one you have there, and it's been an incredibly versatile tool. Great purchase overall. But at some point, I used it with my bigger 9AH batteries. After a couple hours work with it, I took off the battery and noticed that the plastic from the tool was starting to wear/melt/weld into the plastic from the battery right were they slide together. Is there some hidden DON'T EVER DO list that I missed with this tool? Is that common for these tools, to beat up heavier batteries? Have you seen this at all, or heard of it? I treat my expensive 9 and 12 AH batteries like newborns, and this surprised the heck out of me.
The capacity of the battery shouldn't affect the tool as long as they're proper Milwaukee batteries (not Chinese amazon junk)... There's a sensor (thermistor) in the battery that's supposed to shut down the tool if it gets too hot.. Sounds like it failed... I use big batteries in my oscillator all the time there's nothing wrong with that
@@NovaNinja_ I wasn't suspecting that the capacity of the battery was related, just the weight. It seemed to me that something about the way the tool vibrates makes the heavier batteries beat up the plastic of the clip area.
@@operator8014 while you're using the Fein blades, you might as well use the Fein tool; i. e., the MultiMaster. It has the best vibration damping of all the oscillating tools. The Festool is also very good but you have to use Festool blades.
My guess is the bigger, heavier battery has more inertial mass and basically stays in place relative to the tool vibrating around. The smaller batteries probably move with the tool better. The new fuel omt's supposedly have way less vibration felt by the user which would shake the batteries less too.
@@operator8014 Don't know if you'll read this after a year, but I think I know what might be causing the problem.
Guys above me suggested weight, I think it might also be something else.
When it comes to electrical connections like the battery - tool terminal, there is a possibility that the contact area of the connector is too small or not clean, which causes additional resistance, which means higher current which means excess heat.
Also bigger battery packs can deliver that higher current no sweat, which means there's more power drawn from it, yet not so much that the built-in protection kicks in and you probably don't notice it during use.
It might be weight, it might be the contacts, it might be both - added weight stressing out the connector causing it to heat up in use.
I would have just grabbed my 18v makita sawzall... these are good for notches, cutting toilet bolts, along the top of baseboards and sometimes I use it to cut between manifolds when I need to rebuild or re route the water line leaking under a slab.
You can also sharpen the blade even ground brand new teeth after knocking down the old ones with a file.
Don't throw away dull blades
And he is a Philly guy like me! All the more better. I'm loving my O'tool! Learned something here homie.
I've been using the Bosch Carbide blade for oscillating/plunge cutter for several years, last a long time cutting through anything and cost about $10 - 12 /blade in a triple pack. Stucco will ruin a blade but you can cut one opening in stucco for an electrical box if you need to, even though it is not rated for cutting stucco and it should only be used as a last resort. I'd love to see if the Fein carbide blade is moe better than Bosch or not; if you know the answer, please reply. Thx.
The problem with straight cut blades is that you can only use the center area of the teeth because as you get closer to the edged=s the blade bounces more than cuts. they should radius the cutting edge of all these cutters! If someone makes radiuses blades for these tools especially with a longer shank, they would make some money in my opinion.
Hey Vince.
My Sawzall is in the shop and I didn't think I needed it today but I did.
Customer want me to put 2 wine fridges into her 30yr old kitchen cabs.
Needless to say I pulled out the old M18 "Vibrator" and cut through that thing Like A BEAST! on a 5ah
Dont want to say what blade I used, lol.
GO Vince!
If one of my guys grabbed a sawzall for any cabinet work, he'd be grabbing his bags and walking home immediately after.
Thank God you failed upwards into using the correct tool for the job. Blind squirrel, nut, etc.
@@Dave-ek2jx Actually I would have preferred the quicker way around the block.
Of course your only speaking generally because you weren't there.
A sawzall was exactly what was needed to cut the interior shelves of a 50 year old solid wood cabinet. Especially if you know how to actually use one.
Thanks for your 2cent anyway!
I Always Thank GOD!
That I Dont Fail
That I'm NOT one of Your Guys
and I Drive My Own Vehicle.
Squirrel not 2 blind for
"Deez Nuts" LMAO!
Call the Surgeon General. It became a smoker.
I used a bimetal blade to go through 6 hardened screws and the blade still had some life in it. Not much, but enough.
I use these for undercutting door casings for floors to go under them I use these blades till their flat as a scraper blade their little monsters and even almost completely gone still makes a nice cut not damaging the casing just gotta mind your edge and don't force the blade as the age old saying goes let the blade do the cutting
Thanks for the awesome feedback and real world experience CJ!
Yupp no problem and even there being so many variations in blades this tool can do so many things others just cant
Outstanding tool/blade test. Vince, you are & remain DA-MAN!
Vince you never fail to give me some more insight on tools! Very informative 👏 👌 👍
Sir, You are very Precise and Very Real Demo video. Amazing information for us. Thank you.
Awesome video Vince!!! You rock and I love watching your channel every night... your insight... experience and humor make VCG the best of the BESTEST!!! Can’t wait till tomorrow night! You all work so hard for all of us and between the deals out there... new techniques or whatever... you care about your viewers immensely and I thank you!
Thanks Robert, you da man!
Never used Fein, but I do only use carbide tipped blades. Have used both Rockwell and Dremel blades and love them both
“Or is it!?” bwahahahaa that was the perfect set up to a bait & switch 🤣🤣
Not sure if said, but those look like the GRK framing torx head screws, what I use & some good “screws”😉 Very Tough💪🏼.
Pretty nice OMG Blade there. Usually I get the Bosch or Dremel brand blades, as they always in stock around me. Don’t have many Fein blades cuz usually gotta order, & it’s one of those things.....when pull out the OMT, forgot to order, & end up running to store for blades & end up with Bosch or dremel, LOL. Also, do have quite a few other blades from those promos while back. Gotta love buy one get one 😉
That Fein blade was cool going thru the screws & not losing any teethesses. Another difficult material that chews up OMT blades is lath n plaster walls. That stuff eats OMT blades for breakfast, lunch, dinner, & all the snacks in b/t😉
Thx for sharing Vince👍🏻👍🏻
🍻🍺
Hello there hope you're well. Might be a silly question but how do you get the two clamp bits to separate/ open in order to attach the blade? My manual says to turn the lever clockwise at the top then the two plates are meant to open but it doesn't open. Could you make a video on how to properly set up the machine for each blade? Thank you in advance!
You need to loosen the knob and then push/hold it down (like a button.) Insert the blade, then release the button, and tighten the knob. Pull on the blade to make sure it's secure and you're ready to cut. (Don't touch blade after cutting, it gets HOT!)
Great video u think it will cut through the brass plate on a kitchen faucet?. Underneath them screws are rusted bad.
Happy Thursday Evening, VCG and the Gang! 👍🧰👍😍
Mate I bought a fancy as titanium special longlife blade from Bunnings in NZ, and I know I cut nothing by nails, and the blade was gone by the end of the day.
I cut through framing nails, floorboard nails and GIB nails (not screws) and it was dead within a day.
Nice! I'll need to pickup a few of those.
Dewalt 20v Max XR cordless, brushless oscillating tool is my go to. 👍🏽🇺🇸
I wore out 2 blades rated for metal on a #12 screw in a jeep where the head was rounded off. They ate through only half of it and that was after $25+ of blades being destroyed.
Wow 👏 very impressed with that new blade with the screws as well as the drywall screws @vcgconstruction
I seriously worry about your future hearing Vince. Hearing protection, hearing protection, hearing protection!
what did you say ? 👂 😂😂
kingofthecrease30 your funny 🤣🤣😂🤙🤙👌
Omg... that was awesome 🤣🤣🤣
WHAT
Seriously tho, everyone thinks eyes but never ears.
It so easily preventable too
Do I need a oscillating tool ? I don't know but I wonder how much it would cost on the battery deal if I return the extra battery. $111 after return
I have the cordless dewalt XR. I like it. Corded is better for extended use though
3:30 ah yes the osculating blade that burns through wood instead of cutting, forgot those existed. Definitely means there is plenty of service life left in that blade.
Thanks for sharing this video and information.
Glad you like the video..thanks!
I always use bi-metal blades for every application I use my multi-tool. No sense in using just a standard or nail in wood blade in my opinion. The only thing I change is the size of the blade to fit the application
Thank you for demonstrating this blade. Myself, when encountering drywall screws I attempt powering through; oops there goes another blade.
Suggestion: Have your camera person mount the camera. Watching a bouncy video is extremely annoying; what do we focus on. Look at 8:00, the bouncy camera makes watching spatially disconcerting.
Im waiting for milwaukee to release a new oscillating tool because almost every other oscillating tool has a quick insert blade system every brand from dewalt down to ryobi the only other high end brand i can think of that doesn't have the quick access is the makita but their's is a literal block to hold they've been due for a while now
Makita have their Starlock machines in stock. They're waiting until all the old ones are sold then they'll release their new one.
If you had to one to pick between this and the M12 FUEL 3 in. Brushless Cordless Cut Off Saw, which would you pick?
Wow that’s sharp! Impressed 👍 thanks for the advice
Thank you for the support!!
🍻🍺
First time I used a oscillating tool the other day, maybe I might have gotten the wrong type of, bi metal long life from fein, cause after 12 1/4 carriage bottles not a single tooth left.
@@jumper233 that would have been mine also, but the space was to tight, so I figured id try the oscillating since I had it.
I thought he was gonna cut the screw to that's funny anyway you didn't answer some questions you answered all of mine definitely have to change blades I do all kinds of carpentry it's better shelling out a little bit more money for the peace of mind in case you do hit that screw or nail I am very impressed
My dewalt oslitaing tool blades are pretty good they can cut through a twobafour I have tried it as a test. Awsome vid thanks for the info vcg. Osilating tools are safe but I did cu my hand with one. 👍👍👌👌
Your hand looks fine in the pictures.
@@Dave-ek2jx yea it healed
Had a chance to use one of these tools on a bathroom build,if you do wear out the blade ,get ready to spend some money, replacements are not cheap
How is it that drill bits and jig saw bits can sell at a very reasonable price point and multi tool blades (most dont have any carbide) are still set at extortion level price points?
How is the fuel oscillating tool? I didnt get it because it was a brushed motor and didnt want to have to deal with that.
Do the Starlockblades fitting the Milwaukee's without any adapter?
I need to cut a long vertical oak cabinet end to get my new big refrigerator in. Which blade will cut thru it?
Use the whole length of the blade so it doesn't over heat a small part of the blade also use lubricant and allow blade time to cool so it doesn't over heat
How do you like that tool? I love mine got it for Christmas from my boss bc I've been catching on so well and he's been impressed. Thanks for the video. VCG YO
Thanks for the video, I'm going to order some of those Fein carbide blades now.
Is the tool suppose to be off center because that how mine lines up 3 to 5 degrees off center, I'm gona return it
I counted 49 nails! LOL
Rock music can make the most Monday and shit sound cool as hell
Which is best oscillating tool…DeWalt or Milwaukee or other?
Finally I made the 360 comment....bro your team and company are awesome keep up the awesome work and I look forward to all you future videos....thank you...
I knew you could do it with Fein. I picked up the Imperial blades IBOATV-15 hoping I might work.
Will this cut through bone. Cant get any answers online
I was waiting to see the bolt get cut. Oh well...
Wow, being used to Fein’s Starlock, the Milwaukee one seems like to take forever to change a blade
The Fein blades are worth it's price.💪🏽
Babila!! What's good my man?!
Famous Amos, how are you, it's all good here.🙌🏽
No link in the description?
That was wild man 😉👍✅
Greetings from Greenwich London ⚓️⛵️🏰
So there's a difference between nails and screws in hardness term? I ruined a new Curvetec blade being ignorant of that. When a nail I was trying to cut through took a long time, I dialled up the power and when I finally looked, the teeth in the middle of the blade is bald-ed. I re-read the spec for the blade and it says "for non-hardened" nails.
That blade is an absolute beast!!!
To be fair to homeowner type users, they probably just used the blade that came with their oscillating tool...and generally those are garbage. I mean all the teeth can disappear in seconds with cheap blades on the wrong material.
Having been using carbide blades for a while and with even pressure and keeping them in contact with the cut they last ok. If you let them slam into the metal, or bounce around the teeth do chip pretty easy...but that's to be expected from carbide.
What is the link for Carbide TIN coated blade?
Whats a good blade for cutting aluminum
I wanted to to see you cut that bolt not to mention I think everyone else just holds it in place until it cuts instead of moving it around a bit to spread the heat and reducing damage
Can you compare the multi tool Milwaukee M18 and the Milwaukee Fuel M12 please... I don’t know which one to get for my father.
Does that brand make a blade that fits the Dewalt oscillating too ?
Thanks for review.
Are you kidding me? I used a titanium coated carbide blade and I cut two padlocks with it. No problem. I added oil to help speed up the cut and it took about 5 minutes but it cut right through a hardened steel padlock.
I was able to cut through a lag bolt with a bi-metal oscillating blade dewalt btw
I thought everyone knew screws were much harder than nails.
Besides, with needle files you can Resharpen those blades
not all screws are harder than all nails. concrete nails are much harder than wood screws. It depends on what the screw or nail was engineered for. Also, you can use a dia=mond wheel on a dremel to even resharpen carbide tipped blades! Just wear safety glasses cause stuff goes flying!
Cool demo.
actually more impressed from that milwaukee tool, that it did not started to smoke :O my makito wouldnt make that so fast
What about the Robi multi tool oscillating tool when it comes to the blade....????
You also cut them on an angle, which is thicker than cutting at 90 degree
Might help to spray a bit of WD 40 on the blade and nails for longer blade life, normally you do this when you cut any type of metal at high speed. I bet if you done another video using a bit of spray oil there would be a difference.
I'm impressed!
The worst enemy for plunge cutter blades of any kind is heat. Cool blade periodically in water if it gets too hot.
My Hart multitool with a cotton cutting blade on it cuts through about 6,000 nails before it even starts to slow down....
i have a cheap oscillating tool and the blade that came with it smoked / melted on a nail lol
I love my oscillatiing tool. it kicks a**
4:15 wait for it .When he says .The thing is is that
I'd only use an expensive consumable to cut something I couldn't get to with a cheap one
I have only used mine for on drywall and wood no I cut some hardy board once it destroyed a blade and I have bought a carbide blade I found cheapish online but have never used it
Is that ossilating tool a millwakee?
Nice vid
moving the blade side to side makes all the difference.
Really like these vids
if your cutting metal ... use slow speeds .. heat is the enemy ;)
2:45 Yeah that blade's shot.