Worked for me ;) First I was traveling with my printer(c405). Then I had this problem. I started to shaking my printer and rebooting for couple of times. Printer started to work. Thanks
My customer has a C405 with the corresponding error, but the magenta is writing, so I know the ROS "laser" is working as the calibration squares were on the belt, magenta was a bit on the lighter side. I suspect a clogged auger system. I will replace the offending magenta dispenser assembly. A bit of disassembly, but I was halfway there when I diagnosed the device. Was going to use my toner vac on it but decided to replace it instead. Thanks for the video!
I have this error(varying last 2 digits) on a machine with less than 300 prints. Essentially brand new. Rarely used. Still the original toner carts. Oddly it only start3d doing it after i moved it from my house to my workshop. Any ideas? I mean i could understand on a well used machine, but mine is practically brand new.
@@NoComplyDistribution take the machine for a drive. Preferably sit the machine on a hard surface and make sure to drive on a bumpy road. It should dislodge the clump of toner that’s clogged in the dispenser.
The same frustrating issue happens with the c405's brother - the 6515. It's probably the high humidity where I'm at. If you happen to come across one and can make a video on how to replace the appropriate part on the 6515 I would greatly appreciate it. I keep getting 092-318 ADC Y Patch System Fail and I am using a genuine cartridge.
Hello I also have the C405 Printer and it has now decided to print black in a light gray . I replaced the drum thinking it may be the issue and it started to print correctly. Until about a month ago, now it only prints in a light grey print on black and whit only mode, no toner saver mode, paper type is still the same as it was, removing and reinstalling the toner cart was not the issure, remove and reseated the drum, not the issue. So I am thinking that the toner is not dispensing correctly and being channeled down to the drum like it is clogged or has a blockage of some sort. Any Ideas? Thanks
@@ShyRockFreak86 Is it possible that the Auger could possibly be bad as there had been some plastic popping sound from the toner cart area, it has not done it in a while. Then as a test I replaced the drum unit and it worked for about 7 months and its back to light print again. My initial thoughts were the Black toner trey and auger solution, is this trey available to purchse? If so do you have a part number to order or search online for? Is there a reasonable repair center in Wichita, Ks. As a 400.00 service call is really steep for the repair of a printer now days. Any help would be greatly appreciated. Thanks
I just had a Magenta toner error, put it in my can, ran a couple more calls, drove home and plugged it in. It worked. From now on, I will always take these errors for a car ride before breaking them down.
Worked for me ;) First I was traveling with my printer(c405). Then I had this problem. I started to shaking my printer and rebooting for couple of times. Printer started to work. Thanks
My customer has a C405 with the corresponding error, but the magenta is writing, so I know the ROS "laser" is working as the calibration squares were on the belt, magenta was a bit on the lighter side. I suspect a clogged auger system. I will replace the offending magenta dispenser assembly. A bit of disassembly, but I was halfway there when I diagnosed the device. Was going to use my toner vac on it but decided to replace it instead. Thanks for the video!
I have this error(varying last 2 digits) on a machine with less than 300 prints. Essentially brand new. Rarely used.
Still the original toner carts. Oddly it only start3d doing it after i moved it from my house to my workshop.
Any ideas?
I mean i could understand on a well used machine, but mine is practically brand new.
@@NoComplyDistribution take the machine for a drive. Preferably sit the machine on a hard surface and make sure to drive on a bumpy road. It should dislodge the clump of toner that’s clogged in the dispenser.
The same frustrating issue happens with the c405's brother - the 6515. It's probably the high humidity where I'm at. If you happen to come across one and can make a video on how to replace the appropriate part on the 6515 I would greatly appreciate it. I keep getting 092-318 ADC Y Patch System Fail and I am using a genuine cartridge.
como se llama la pieza donde va puesto el tóner , esa que tienes en la mano en el minuto 4:43, se puede comprar?
toner dispenser
Excelente información, saludos desde Guatemala
Hello I also have the C405 Printer and it has now decided to print black in a light gray . I replaced the drum thinking it may be the issue and it started to print correctly. Until about a month ago, now it only prints in a light grey print on black and whit only mode, no toner saver mode, paper type is still the same as it was, removing and reinstalling the toner cart was not the issure, remove and reseated the drum, not the issue. So I am thinking that the toner is not dispensing correctly and being channeled down to the drum like it is clogged or has a blockage of some sort. Any Ideas? Thanks
The Toner is a 68% full on the black I forgot to mention and the drum has maybe printed 100 sheets since replaced. I am out of idea's. Help....
@@spyder1857 I would try replacing the transfer roller. But I have a feeling it’s the MCU board not giving the correct voltage.
@@ShyRockFreak86 Is it possible that the Auger could possibly be bad as there had been some plastic popping sound from the toner cart area, it has not done it in a while. Then as a test I replaced the drum unit and it worked for about 7 months and its back to light print again. My initial thoughts were the Black toner trey and auger solution, is this trey available to purchse? If so do you have a part number to order or search online for? Is there a reasonable repair center in Wichita, Ks. As a 400.00 service call is really steep for the repair of a printer now days. Any help would be greatly appreciated. Thanks
I have a problem with xerox WC6605, error 092-671, do you have any video with solution?
@@germanmartinez7560 sadly, no. Good luck!
How did you clean out the feed auger?
dump it in the trash.. but, I'd recommend taking the printer on a small road trip for a few blocks, making sure it's a bumpy road.
i am a xerox direct tech. after reading the service edoc. It look like a pain in butt just to get into ros. ugh!. Mine is missing the blue patch
catch 22, gotta take the cyan dispenser out to get to ROS, or put the printer in your van and take it for a ride for a few miles.. not kidding
@@ShyRockFreak86 GREAT VIDEO. Do you have any of these printers as a spare or that needs work?
I just had a Magenta toner error, put it in my can, ran a couple more calls, drove home and plugged it in. It worked. From now on, I will always take these errors for a car ride before breaking them down.
@@Sammym800 I do not keep spares. I’m a major account rep. We repair 99% of these machines
Thanks for sharing.
hola, tengo error 093-320, me puedes ayudar a entender? saludos
The developer motor is not turning.
No video on how to unscrew. SMH
I'm having this issue right now
unscrew what? this is a teardown video.
do this first ruclips.net/video/f4J79807Cow/видео.htmlsi=xm6sHsLX3Zjaavch
Complete garbage.
@@hamradiotimes5586 my video? Or the printer?