I just realized that the first locomotive has fully functional walschaerts valve gear, if you look close enough you can see the slide valve stem actually in good timing when going forward
Yes! The failure to reproduce that crucial characteristic of Walschaert's motion very seriously detracts from the realism of every modern OO gauge locomotive with which I am familiar. When a manufacturer clearly had the skill and miniature engineering resources to reproduce it so far way back when, I find it quite incomprehensible, actually unforgivable that not one of them (at least to my knowledge) is either capable or willing to provide that level of realistic detail today. Otherwise, this was a very interesting presentation by Sam, as professionally articulate as usual! But I'm still not entirely satisfied with the slow speed performance of ANY model steam loco. There is definitely still room for improvement in the synergy of motor/flywheel(s)/gears.
@@John-Tropi I agree - Consistent and steady low speed (and crawl) is still an issue, and the high speeds are totally out of scale. I scratch-built a diesel-style loco and used a Chinese general-purpose motor with a built-in reduction gearbox, driving the wheels with a Meccano chain drive. The crawl speed was incredible.
The can motor, flywheel, and gear tower mechanism in D5317 originated in the states. A company by the name of Athearn produced locomotive kits that came in blue boxes that used the first iterations of the mechanism. At first it was without flywheels, then they were added in the 70s Athearn locomotive releases.
I started with the early Hornby diesels: one power bogie, and only it had current pick-ups, then Lima: Ringfield motor on one bogie only, but did have pick-up on both bogies. Which it needed as the fitted traction tyres lost some pick-ups. Neither ran very well. Now, I have Athearn-type mechanisms: all wheel drive and all wheel pick-up. By far the best solution for good running, and able to cope with momentary current loss on dirty rails, and through insulated point frogs.
In the 1970s I changed to N Gauge. I was quite upset with Rheumatoid running of my Lima AL6 (Class 86). It had a ringfield motor bogie one end with traction tyres and a pick only bogie at the other it wobbled when running and stuttered and stops at slow speed and only seemed to run properly at high speeds. I went to an exhibition in Chester in 1970 and saw a layout using Minitrix locos. They had a central motor, 2 x universal joints, 2 x worms and two bogies with gear towers. These had 8 wheel drive and 8 wheel pickup, with excellent slow running and would pull 12 and 14 coach trains....I bought a class 27 for £7.30p. Although not used much now ( I have gone back to 00 now) it still runs, as all my Minitrix locos, as it di dY one. These are all 3 pole motors. Thanks to Bachmann leading the field, nearly all 00 diesel locos are like this now. N gauge seemed to lead the field long before 00. This was progress that made a great difference to running! John Harrison. Wallasey, Wirral.
This motor design was used for several years. A lot were horseshow magnets, so did end up similar to the one you showcased. For the time, they were really great and exciting. The old half wave rectified controllers and battery controllers of the day were not quite as smooth as the newer controllers, but they do work better on full analogue controllers rather than modern electronic based controllers. I find the way they speed up slowly adds a bit of realism as real life locos don't go from 0 to full speed instantly. It takes time to get up to speed. The very early plastics were acetate based and they warp and split so badly as they get old. Later plastics were a bit more stable.
I was auditor at palitoy in mainline days. Always used to buy one of each loco as ‘best’ but had a constant invite to delve in their scrap bin. For every three locos out of the bin I would recon on one good loco, one ‘useable’ loco and some scrap/spares.
@@SamsTrains When I moved to California, 40 years ago, I brought my Hammant & Morgan controllers with me. What I found was that just upping the voltage with voltage converters didn't allow them to put out full power, so I replaced them with more recent American controllers. I found they worked perfectly with the old Hornby Dublo and Triang locos.
I no longer model, but back in the day (1980-2000) I became obsessed with slow running. It's the Achilles heel of smaller gauges and I drew up all sorts of designs using 5 pole motors with massive flywheels and huge reduction gearing. None of which came to fruition of course but all my locos were modified with pickups on all wheels etc. in a vain attempt to recreate the huge mass of the prototype. Very interesting walk through the history of OO loco design.
my gaiety tank with the factory 5 pole and 47:1 gearing actually ran worse at slow speed than the quality dublo 3 pole and 9:1 gearing. I've thrown in that crucial word "quality" you'll note. tbh, my example may have been really worn out, that mass of gears was very noisy, but it didn't really give those outstanding results that the mechanism would appear to promise. and if it was worn out, would the same vintage dublo mechanisms be any better?
Interesting video. I have a sizeable Dublo collection and am aways impressed how these still run 60+ years after they were made. The build quality is absoltuely bombproof and I imagine they will still be going strong in 2060. I wonder how today's offerings will fare in 20 years' time, nevermind 60 or even 100. As for features in the future, personally I would almost prefer fewer features and lower prices. The simplified approach that Hornby took with its 2-Bil and 2-Hal models seemed like a good one - they are decent looking models and pricing was very attractive.
I know they don't! I helped rebuild the 'Mostyn Junction' layout at Wirral Transport Museum, Birkenhead. We bought numerous models old and new to run the layout.A lot of the new Hornby an Bachmann locos are on their 2nd and 3rd motors in the 15 years or so that the layout has been running with its own stock one Castle class loco had to have a new armature after being knocked off the track and left for an hour! The other Dublo loco that stopped, one day of running, was stripped down and was found that one of the brushes had worn away down to the spring! These were probably the original brushes from the 1960s!!! Long live Dublo!!! John Harrison, Wallasey, Merseyside
I have a 1940s Hornby-Dublo Duchess of Atholl. The internals on that are pretty much identical to the Wrenn loco you demonstrated - even the magnet design and other details. Great model and still working after conversion to two rail pickup.
Later on I worked for Beatties of London ltd who stocked Hornby, Wrenn, Palitoy, Airfix and Lima alongside Fleischmann, Trix, Märklin Roco and Rivarossi. That experience opened my eyes to the vastly superior quality of the European manufacturers and models. Frankly the British outline stuff was rubbish, especially Hornby. The European models were all superior runners, better made and detailed, and included features such as working lights that most British models were devoid of such as lights. Mainline were the precursor to Bachmann. Airfix fell by the wayside eventually but had a good stab at it. An interesting journey through the past. My time selling model railways was around 1974 to 1976. It would be great to see you feature some vintage European models in a show.
Very interesting subject. The most interesting thing is that more than half a century old technical designs can still run beautifully on today's layouts with today's hardware! That's what i would call sustainability. We can't say so for way too many other things... By the way I think the future of model railroading and also other modelling hobbies is 3D printing and DIY approach to making and fixing stuff. It can be more fun, more diversity in models offered, and also, more sustainable.
A lot of trains from the 40’s were pretty clunky and more mechanical. Especially in the O gauge range. When I got a 1948 Lionel Columbia Scout for my grandfather, it was quite bulky, had exposed sprockets by the wheels, and was just an overall very bulky locomotive. But a cool one too!
Interesting video . The thing with model locomotives is I don't think they suffer from Planned obsolescence. So when it comes to modern locos it's all about development and what's available at the time. Simply it's just that when it comes to model railways products they have the opportunity to develop properly without being held back by Planned obsolescence.
Have you ever considered reviewing or purchasting a brass locomotive for your personal collection Sam? Many brass models are very highly detailed even by today’s standards and were produced in the 60s-80s
I appreciate towards the end when you acknowledge the limited nature of this video. The title is perhaps better than many other RUclips videos that have the vaguest of titles, often not really related to the video. So, 'A journey through time' may have people watching from an idea that it was more about a range of changes to model railways, including different gauges, the 'curious' three-railed models [that I could not relate to because of the lack of realism] to a fuller understanding of railway adhesion from real rail locomotion. As a young child, my older brothers' 50's [UK] version of Triang-Hornby used 'Super Four'? rail track. My more realistic 60's 'System Six'? track, meant that my brother's shunter engine wheels' flanges 'knocked' on my tracks sleepers. Maybe DCC programs for a smoother acceleration from the start - I've never seen a real engine instantly accelerate to high speed. [I'm amazed though at how our real electric suburban rail in Brisbane, Australia can accelerate and decelerate at station platforms.] My Australian version of an electric engine, in plastic, had a hollow area under the flooring for a heavy metal weight. Understanding better about real railway engineering and adhesion, even 'light rail' is still heavy, and necessary to keep rail vehicles in contact with the track. Today, with interests in real railway passenger and freight transport, I'd be interested in making my own N and/or Z scale track in closer to reality dimensions of track height and width - even though I'd need some good magnifying gear for my visual impairments. Some 300 properties are to be 'resumed' - including my neighbours' houses for a new straight four-track rail corridor in Logan City, Queensland - focused on 'faster rail' between the Gold Coast and Brisbane for Australia's 2032 Olympic Games. It ignores the historical fact that we were proposed [standard gauge] interstate rail on this corridor about 120 years ago. Some parts of Australia can be called 'fifth world' today. I was disappointed as a child of engines stalling, 'humming' and the 'jerky' movements. As model rail wagons and engines were often 'foreshortened', with curves much sharper than reality, I'd say that having models run at slower speeds and smoothly is necessary. I had already worked out for realism to change from the OO/HO gauges to N Scale was necessary for realism in a large room setting - or even Z scale. Unfortunately, I've gained long-sightedness and other visual impairment in later years - meaning I'd have to erect some small cameras around a diorama to see detail on a large screen today. Currently, some parts of Australia are worse than UK's Dr. Beeching's Axing, causing some extreme neglect to people with disabilities in rural areas not having access to everything from appropriated medical care in large cities, going to the beach, nor seeing family and friends etc. Some of us die on terrible rural roads and truck-filled highways now.
So back in the 70 I don’t recall going slow . It was full tilt boogie . And if it went around a corner with the left or right wheels off the ground . You was doing it right
My Father always said that if one drove through a corner in a race car with all four wheels on the road, one isn't going fast enough and the suspension needs more engineering time, and driver needs more track time. If the vehicle was 'cocking it's leg' through a corner, then it is getting closer to being driven on the edge.
I have thoroughly enjoyed your presentation. I have learnt a lot and I think your choice of models was excellent ! The close ups of the detail work is super. I clicked on your vid not knowing it is UK. But your information is pretty close to what is happening here in the US. Thank you for explaining the difference between 5-pole and coreless. Ever since Kato came out with coreless a few years ago I expected it to be "the revolution". Kato's interpretation is to put the motor right on top of the power wheels. I haven't seen any demos of their slow speed performance. Seems like that would be a tremendous freeing up of space for circuitry and speakers. Much success to you and I am happily subscribed.
The first Black 5's also had the first ringfield motors, I have one. Their valve gear also was borrowed from the "Britannia". To your end question, I have two " duchess" class that are 1977 & 1982 versions and had working lamps on the front, fairly weak, but they worked. Hornby could do that so much better now, it would atleast be nice if they revisited the concepts. Being from "Across the Pond" lights are standard on Locomotives. I'm not saying that ours are superior, I wouldn't be collecting and running UK prototype if I didn't like the "English" steam. And I'm the only one who works at my local hobbyists that can intelligently discuss UK prototype, thanks to shows like yours.
Interesting presentation. I would like to see this same sort of video done for USA locomotives, and for other European locos such as the Italian, the German, and the Austrian locos such as Roco. I'm particular interested in the tender drive developments in the Roco line
since about 1989 Roco also added too the tender drive a driveshaft from tender to loco (similar to Graham Farish oo) in some models, giving quiet loco + tender drive with good pulling power, don't know if they were the first to do it
Hello Sam, I enjoyed your take on this and especially at the start of the video your note about compatible controllers etc. I am very much a vintage model railway enthusiast and am running all the early models you showed very successfully at scale speeds on my Tri-ang Super 4 based layout. These excellent models still have much to offer if you treat them to careful maintenance and of course there are period upgrades too, such as the superb five pole X03 / X04 Airfix motor conversion. Take care, all the best to you
Very interesting article! My main love is Hornby Dublo 3-rail - apart from the upright motor in the Duchess's and others they also made the first 'ringfield' magnet motors, in a couple of forms, with modifications. Very fine performers too! I also convert 'moderns' to 3-rail (a bit bonkers maybe but I started with a 3-rail set-up!!) and agree totally regarding the Mainline motors - they really aren't up to much are they! The Bachmann split-chassis locos run well but getting to the motor to wire in a 3-rail pick-up is a right pain! I have 3-railed a Bachmann Peak and that runs and pulls really well! Again I agree totally about the quality of the early 2000 Hornby locos, I have 3-railed a un-rebuilt west country and a princess and they are really superb runners. The Lima range is worth a mention too - their Deltic and class 40 are fine performers too, as is the small prairie, similar ringfield motors to Hornby.
I agree with the Lima small Prairie. I have one it's like a tank will pull anything you put behind it and could be thrown from a 10 storey window and finish in one piece
Yes, and the original ringfield motors were put into the locomotives of the Caste, 8F and Merchant Navy, not in the tenders. Unfortunately, they protruded into the cab.
remember dublo didn't use the first ringfield motors: just that the common and well-known dublo ringfield was produced before the common and well-known post dublo variety
Sam. That looks like a G&R WRENN example, or Tri-ang/WRENN. It is fitted with Tension-Lock couplings and has metal tyred, spoked, bogie wheels. HORNBY DUBLO ones had DUBLO/PECO TYPE and smaller bogie wheels. Yours looks like 1966 on loco.
The reason we have OO/HO (1:76 scale bodies running on 1:87 scale chassis) is because the ‘best’ available motors were German but German locomotives were larger, so to accommodate the German mechanism in a British outline we adopted a slightly larger scale for the body. Back in the 1960’s it was noticeable how much better the old 3-rail trains ran (well compared to my own Triang locos anyway) with fewer stoppages on spots of dirty track (these days with DCC we could add a ‘keep-alive’ supercapacitor to cope with dirty track). From memory the people at Pendon really drove the development of the coreless can motor. By the 1980s I was using N Gauge (having been given a Farish ‘train set’ in the late 1970s), not great, fitting additional pickups and adding weight made a big difference. The chap who popularised N gauge had to wind his own motors but they ran beautifully on his ‘in a violin case’ end-to-end model railway. I think the chap who built the H0 gauge Madder Valley (a personal favourite on display at Pendon) also wound motors for his own builds. For the future I would like to see an inexpensive loco with DCC and the super-capacitor keep-alive added to provide decent running and the wider use of the Microtrains couplers to allow shunting (something I found a little frustrating with the old Triang ramp-between-the-tracks uncouplers). Once the customer has been hooked they would then likely invest in the more expensive but more detailed locomotives, although with a good running basic loco you could still have a lot of fun (see for example your own 3D printed engines). Kids like ‘operating features’, opening doors on wagons and vans, container cranes that actually lift containers on and off wagons and conveyors and silos to load coal and aggrigates. One thing I experimented with years ago was to use the small programmable sound discs made for ‘singing’ Christmas cards to add the sound of carriage doors slamming (although that sound is probably before your time), you need at least two, one for lots of doors on an express or commuter run and another with just a few for the quieter periods, they will fit comfortably under the platforms and can be controlled by a simple battery and push button set up. That sort of thing is harder to find these days and finding a user-programmable one is very difficult.
Sam. I have had Hornby Dublo from 3-Rail days. Some of the first loco'swere a bit notchy, but some later models had the Meccano/Dublo (loco driven)Ring Field motor. This was very large, long motor, but much smoother than the originals. One of the best of these was the the re-built West Country loco. This was produced as Dorchester and Barnstable. One was 2-Rail, the other 3-Rail. I have a 2-rail one and is 3-pole, but is so well geared that it will double head with a modern Hornby 'Battle of Britain' and even crawl at similar speeds. This is a much heavier model and will pull more than its modern equivilent. In regard to the early Tri-ang locos, try them with the controllers of the time! In comparison to the Dublo, there really is none!!! They were cheaper. That is the only good thing you can say about them, also they made more popular loco types than Hornby Dublo (in my opinion, of course). Tri-ang had oversize flanges and cast mazak wheels that were not plated so didn't pick up very well without constant cleaning. These will not even run on code 100 track as the flanges bounce over the track chairs! The valve gear on Dublo locos was simplified and over size, but Tri-ang's, what there was of it, was also and 'very' simplified. Also with Tr-ang the buffer height was about 1/8"/ c.3.5mm too high on allthir models. Dublo's models were scale height! If you put a Dublo loco next to drawings, they were, in general, scale size. 2 Dublo locos were not; one was their N2, which was similar, but not an actual copy and their Deltc loco. So I have been told, this was built from 'memory' after the designers had been shown the real loco being built. They got it very wrong and the model was very much too short! It did have a very powerful ringfield motor bogie and die cast body, it also came out, I believe, before the real loco! Unfortunately, their coaches were flush glazed, but short on length too with lithographed printed details. Tri-ang loco's were nearly all too high above rail level and a lot were very short. The Princess was about an inch too short compared to the modern models. Their 1960s mk1 coaches were scale length, but not flush glazed until the late 1980s and still about 3.5mm too high above the rails. Tri-ang motors used 2-start worms on their motors which made them start at about 40mph and had a top speed of around 130mph!!! To conclude, there really wasn't any comparison between Dublo and Tri-ang. Dublo was far supreme in detail, weight, pulling power and scale. If anybody comments about Dublo to me, I tell them about the pulling power of the Dublo 8F 2-8-0. I once ran a thirty five coach train of mark1s on the 'Mostyn Junction' layout at Wirral Transport Museum, Birkenhead. The 8F was slipping a little on curves, but pulled the train, consisting of Triang-Hornby, Mainline, and Hornby mk1 coaches for about an hour! When first introduced, this model pulled a 3 year old child on a special display track at that years Model Engineers Exhibition, showing the power of the ringfield motor in the loco! I hope this rant will be educational to you and hope you try out and compare a Hornby Dublo Barstable loco to a modern Hornby one.....You'll be very surprised!!! Best wishes and keep up the good work. John Harrison. WALLASEY, WIRRAL.
Back then it was half wave rectification with metal plate rectifiers and variable resistors to create voltage drop. No semiconductors to give thyristor control let alone feedback circuits. Many DC controllers still use 1930's output waveforms though!
13:10 Hornby-Dublo developed the ringfield motor back in the 1960's. I have a couple from 1962, and they do run very well, but the controllers were more powerful for all the weight and current needed to pull long trains back then.
The original battery powered Rovex 'Princess' with 2 coaches plus track was my first trainset with the loco current collection being from 2 sprung brass plungers that came out of the body under the front of the firebox. The one you are looking at is a later one! I have no idea what material these original train sets were made of but in time the whole lot started to 'curl' and distort. Including the battery/ controller box which contained 2 or 3 Ever-Ready 'front bike light' double batteries. Unfortunately, in time, the battery box distorted so severely that the trainset became unusable as an electric one so it became a push-a-around the oval job with the 2 short coaches and loco hobbling and derailing beacause the all wheel tyres on the set had developed grooves and the coaches assumed a U shaped form. Just like the rest of the train set! However, one day when I licked the tender body with the tip my tongue so I could stick something on it's side there was a strange burning like sensation on the tip of my tounge! Talk about toxic toys! I can assure you I have never, ever, licked a train set since!
what a cool first trainset: back when it was perfectly fine to run a 2 or 3 coach euston express hauled by a stunted princess, around a mass of track. in all honesty, I think with our current fixation on almost photographic reproduction of a particular time and geography we've lost the ability to just enjoy a model railway as a model railway. one still can of course, but one gets categorized by others who consider what they do is the "correct" way, completely overlooking that essential factor of "who cares?". on a slightly more constructive note the early plastics were an acetate (same as film stock) which caused the warping and mis-shapeness, progressively changing over to polystyrene from the late 50's
That Royal Scot is actually the version Palitoy produced initially for their Airfix GMR range. It was markedley different from the one produced for the Mainline range - different body mouldings, different chassis and motion gear, different finish, too. The Airfix ones initially went to Dapol, with a couple of Dapol originals and most of the erstewhile Airfix GMR range eventually going to Hornby - the Scot in the vid being discontinued due to it's rather grouchy chassis. The (different) Mainline branded one and it cousins the Jubilee, the re-built Patriot and the 'parallel' Scot did indeed become the backbone of the initial Bachmann Branchline catalogue - though as I've mentioned above, these quite different from the Scot in video, it being the Airfix GMR version. Great vid though, Sam.
I've got models from my own country produced in the 80ies and onward and it's fun(ny) to see the development of various manufacturers when opening them up and seeing how it was first all analogue focussed with track pickup at various points, to 8-pin DCC ready but still using just 2 mini light bulbs with light guides to both ends, to LED use and 21/22 pin connectors.
Sam - great video. At the end you asked what more would we like to see on model locos. The answer is LESS not More. From my perspective, as a modeller and operator, rather than collector, I would like to see dimensionally accurate but less detailed locos at a cheaper price. More like the Hornby Railroad. In that way we can customise and detail ourselves which is a big part of the hobby. I would also like to see modern mechanisms being made available by the likes of Hornby and Bachmann so we can upgrade older models at a reasonable cost and without having to resort to making our own mechanisms. A model railway company in America supply three different qualities of loco at 3 different pricing points: Museum Quality, Rivet Counter Quality and Operator Quality. It seems to me that is something the manufacturers of British trains should consider.
Interesting video, thanks a lot Sam. The Wrenn locos were generally smooth and really powerful. I would suggest that the reason your Duchess is a bit sluggish is because the motor need remagnetising which is fairly easy to do, and understandable after decades. The advent of plastic and nylon in mechanisms has been both an improvement and a backwards step.
With the good old Dublo and Wrenn locos the sluggishness and worse was usually down the the magnet losing its magnetism and also lazy maintenance with the oil can. There are super magnets available to replace the old ones available on ebay. My first loco was a Duchess of Montrose which would have been 63 if fatigue and not so gentle treatment. The old Rovex would have died much sooner. I bought my HD Barnstable in 1967. It is play worn with only new magnets and driving wheels being replaced in that time. Like all locos of that era 200 mph was the standard express speed as their controllability was sort of limited. Speed drop off on inclines was formidable however these locomotives were huge fun to play with and still are. Stuff realism.
I honestly hope that in the future, they stop using pick-ups on the engines. Battery-power or rechargable batteries fitted into the locomotives could give a much more constant flow of electricity to the motor, which would relieve the need to constantly clean the track, or such things as praying for your smaller engines to get over the express-points. I realise all of this would probably mean radio-control, but honestly, that doesn't seem like a bad thing. No more worrying for what's DC or DCC. Just pure undisturbed control. Ain't that a thought? :)
That's an interesting idea! The problem is that everyone with a OO railway already uses electrified rails and has a controller... any manufacturer who goes against that risks putting off the vast majority of their potential customers. With how niche the hobby is, I think we're too deep down the electrified rabbit hole to ever return Thanks for watching, Sam :)
radio control sounds sodding awful, and just use live frog points, the east Germans had been using plug and play no issues live frog points since the mid fifties: hornby dublo should've had a look at what other manufacturers were doing with points design when they went 2 rail
Couldn't afford a tomix set sooooo decided to make my own... Hasn't that been fun lol... First attempt at running it just wanted to torque of the track then the shafts vibrated out.. had to get rid of some play so I don't throw my drive wheel If it bound at all.. now I just need to get rid of the play in the carriers axles as I kept jumping the track.. now I'm trying to decide whether to coat in dielectric coating or di tape.. or pain staking wire laying on the edge of the track.. or over hang like some trains trams etc ...the fact I even have it operational in a day I was stoked for $20 work 🙄👍
It would be interesting to know more about your DC-controllers: Are they controlling the DC-voltage or do they have a pulse width modulation (PWM) which would improve slow motion movements highly? Worm-based transmissions save a lot of space, they could replace several pairs of gear. But they are prone to wear so they are used rather in toys than in real world applications. Models with a worm-based drivetrain have a different braking dynamic than those without it. Worms are unable to transmit forces from the wheels to the motor, so the dynamic just depends on the rotating masses before the worm, in result the rotor in the motor and a flywheel if present. So the bigger mass of a metallic housing does not help. The German brand Fleischmann used to have the "Rundmotor" for decades, a relatively slow turning motor which allowed them to avoid worm-based transmissions and use very simple gear transmissions easy to maintain. Märklin used to have a similar positioned motor.
You've completely omitted Trix Twin and Graham Farish. Graham Farish put the motors in the tenders of tender locomotives, and drove the locomotive driving wheels through a drive shaft and gears. The motors regularly burned out, so people just replaced them with the Triang X04, which was easy as they just had to be attached to the drive shaft. Trix Twin were originally AC 3-rail, with enormous wheel flanges and crude bodies. In the 1970s they came out with a range, mainly LNER Pacifics, that were as smooth as any modern locos and much more detailed than their previous range. You forgot to mention that the pre-war Hornby Dublo range was 3-rail. The 3-rail wheels had an enormous rolling resistance, so you would be lucky to get your loco to pull more than two coaches. The Wrenn model that you showed was based on the Hornby Dublo 2-rail version, which had plastic tender and bogie wheels, and a plastic tender body, so it was not a good representative of Hornby Dublo in the early 50s. Most locos in those days shot off like a rocket the moment you turned on the controller. The H/D Duchess locos and A4s were renown for that. I don't know why the one you had was so sluggish to start. Several of the more modern locos that you showed were very jerky: a lot more jerky than the Hornby Dublo locos were. Don't get confused by the term "Ring Field Motor". The first locos to be fitted with ring-field motors were the H/D Castle, 8F 2-8-0 and Merchant Navy, and the motors were IN THE LOCOMOTIVE, NOT TENDER. They went on to use them in the Diesel Shunter and the Deltic. You completely omitted the Airfix range, which, like Triang-Hornby, put motors in the tender of tender locos.
Superb video. It was mainly the motors. I replaced my Triang Jinty with a modern 24v motor and a nylon worm and it runs like a Kato or Fleischmann loco now. I also have a 1940 HO Gilbert-American Flyer loco and again if it had a different motor it would run so better. One more thing, Hornby tender drives was a backwards step from what Triang offered. You are right too about controllers. They are amazing now compared to what was around in the past.
@@SamsTrains I can't wait! You can see the Jinty in this video along with some other 24v motor and nylon conversions. ruclips.net/video/_vwsHd1FnVY/видео.html
The one thing that I will add in here which of course it was reflected in the prices of the items at the time But the hornby dublo duchess models were very good in model terms. Dimensions were good with modeled valve gear and multiple small details. When they run they look like a miniature version of the real thing The early tri ang models were more of a toy with very little for details and valve gear, plus it physically looks like dimensions are off, they don’t have the sleek look that real locomotives or even hornby dublo had The tri ang had the price going for it which is why they became the big company as time went on But as far as the actual models go and the functionality I find that hornby dublo did a lot better job of actually capturing the real life versions
That's a good thought - would have been very interesting to compare those! Thanks for sharing your thoughts, and certainly true that Tri-ang were much cheaper! Thanks for watching, Sam :)
I had a Hornby Dublo kit from the late 1950's and early 60's. I had a controller that received its power from a second-hand lionel box. It had a Canadian Pacific loco and caboose. It was the version of rails with the tin-plate base and center power rail. I purchased the mail car set with my own money. On a visit to Britain in 1961, I received a second loco with the ring field motor. The only thing that I remember about that loco is that it would not run on my layout. I'm not sure what the issue was. Power supply being 60 hz? I'm not sure. I also got a second controller that was complete with transformer built in to plug into 120 volts split phase. (Split phase took the output of 240 volt supply and used a central neutral to give 120 volts on each side of the neutral. So a electric "range", dryer or water heater would operate on 240 volts.) In your review you did not cover the merger in the 60's of Hornby and Triang. That seems to be when Hornby started using the triang style coupler. (That seems to be the de-facto coupler for U.K. model railway use. North American trains use a different style, with an alternate style called the KD coupler being available as an after-market upgrade.)
I have a Flying Scotsman train set dated 2006. The loco has a 5 pole Ringfield motor and runs beautifully, as good as my new Princess Royal and Princess Corination locos - maybe I am lucky?
Probably not just lucky! The 5 pole ringfields were a big improvement in performance... but they are quite rare; implemented just before they ditched the mechanism completely... so you're certainly lucky in that sense! Thanks for watching, Sam :)
@@SamsTrains I have added my own pickups to Bachmann steam loco tenders where I have bought second hand but I avoid buying new Bachmann steam locos that don't have tender pickups.
I have the same Pannier tank from that era and when I brought it off eBay it ran as smooth as butter, it was shockingly superb, even the crawl was impeccable. However I dropped it and some parts fell off so it doesn't run as well
That 70's class 9F Evening Star was my first model train! Glorious to see one still going strong. I remember it being super powerful, to the point where I could get it to wheel spin when starting under full power, and it could pull as many coaches as I could afford to put behind it at the time. Didn't like crawling at all though. Great train for the day.
I remember seeing them at exhibitions with wobbly tenders, caused by traction tyres, and sticking valve gear and wheels static and still being pushed, sliding, along the track....Horrible!!!
I had a Black 5 (tender drive) tha was awful. I fitted an X04 motor to the loco and replaced the traction tyre tender wheels with solid metal ones and wired the two motors together. The tender wheels did slip a bit as they rotated faster than the X04 in the loco but pulled 3 times as much stock, without the tender wobble and did not stop over any dead frog points!
What I didn't hear in your review was whether the trains performance modeled the train of which is a model. My philosophy is I want a train that reflects what it represents, not to win a drag race.
Interesting retrospective Sam ! And I remember the first Märklin loco's I bought in the early 70's. All Die-cast and the motors were not that bad but not with slow speeds as today. I changed to 2 rail DC and since 2014 DCC and there we look at more refined performances in the speed spectrum. Not to mention the sound. Looking back just one 'generation' and O boy what a difference ! My dream loco's: onboard power for HO and OO scale. No dirty track worries and easier to build layouts without all the wiring and polarity issues on points. With the smaller and more efficient motors it's maybe not that far off. Thanks for sharing !
A great summary of 00 model developments over the ages. I had an early Dublo N2 with a horseshoe magnet, which had much less power than the standard 1960s N2. I don't think we even tried to make our locos crawl back then; we were grateful to have any speed control! - just try getting a clock-work loco to crawl... Graham Farish produced some 00-gauge locos and stock in the 1950s, using early plastic: good detail for the time, but if you were not careful, the wheel flanges would break off. Their King class loco had a weird motor, with a rotating armature consisting of the permanent magnet, surrounded by electromagnetic coils energised by an arrangement rather like the 'points' in a 1950s car distributor! That was in the tender (with plunger pick-ups); a flexible drive shaft to the loco enabled the driving wheels to do the work. Again - crawl it did not: you had to turn the controller full on to get it to start moving!
I am 61 years old and have my Uncles Lionel Locomotive and tinder with smoke cir. 1940 the engine is easy as heavy as a red clay brick, cast iron , still runs.
Great Video Sam. Thanx for the Education. As I was born In 1956 my first Loco was a Triang Black Princess and The O8 Shunter quickly after..! I lost most of my Train Set in the Move to Oz. In 1980. Damn it..! But Started again at the Birth of my Son..! Great Video. Cheers All. Kim in Oz. 😎
Great review. I remember those X03/X04 motors - they used to emit a characteristic ozone smell when they ran. I would like to see the manufacturers fit as standard, much more realistic and functional couplings - those tension-lock types are ugly and useless and don't match the huge improvements in accuracy achieved in other areas of the models.
Absolutely. At the very least, that all of the companies make compatible Tension Locks - the current ones are subtlety different and come apart if two different types are coupled together.
I had an early Hornby Dublo train set. This was three rail (centre rail live) running. Some models ran better than others. My basic set was second hand, and had early die-cast metal locos. The best runner was A4 Sir Nigel Gresley in LNER garter blue. Metal die-cast body. A later addition was an LMS Duchess class - Duchess of Hamilton. Plastic moulded body and, while a reasonable runner, didn't have the pulling power of the A4. Don't remember much about the motors as I only gave them the occaisonal run. The layout covered the entire floor of the front room and my mum didn't like me getting it set up! When Hornby introduced Dublo they thought they could make everything "half 0" scale. But early eletric motors could not be sourced that small. Forcing them to build the locos and rolling stock in 1/76 scale. They had, apparently, already produced track in the HO scale (1/87) and could not aford to scrap it all and start again. So Dublo trains ran on HO scale track in their sets. Hence the instability over tight curves of models running at too high a speed.
the early hornby dublo were very well engineered and a robust lot weren't they? regarding the availability of electric motors that was all a bit of a myth, especially the fact that hornby designed their own and would've designed any to fit the working area. hornby hadn't actually made any track previously: the tinplate track was of course based on the proven marklin design. the 4mm to 1ft was of course just a leftover from bing, and it worked and allowed for the real reason of the narrower than scale gauge: axle boxes, always an issue for many years
All the Hornby early Silver Seal locos had the early six wheel drive Ringfield motor.... 9f, Black 5, Britannia and the original two tone green 47 Sampson.
Excellent video Thank you for it. One note: the motor type you show in 11:21 (or in 19:35) is not a CAN motor but according to your own video it is a "square bare motor" (Block motor in German), very popular in 1964. A CAN motor (like in 23:40) is usually a cylinder shape with a metal coating. This does not remove any of the qualities of your video. I wish an equivalent was made for Märklin locos (a very rich subject). Strangely you mention Hornby golden era (for motors & transmission) being in 2000, for Märklin this golden era was in 2004 with SDS (Soft Drive Sinus) motor, tiny, ball-bearing-mounted, helicoiday winding, no-collector (rotating field), total silence. Alas this was phased out after Märklin filed for bankruptcy protection in 2009
Dear Sir, This was a very innovative and interesting video. I probably knew all of the shown engine generations (not personally, though), but have not seen them before in a evolutionary, cronological presentation. Cheers from Brazil!
Hi Sam, Sadly, I need to correct you. Palitoy didn't directly become Bachmann. After the Palitoy "mainline" brand, you had Airfix ,GMR & Replica Railways all releasing the same models before Bachmann took over the molds. All they did was to have slightly better motors whilst still using the split chassis. I remember the joke about the Palitoy/Airfix/GMR models was, great detail BUT if you got a good runner you were very lucky!
Others may have said this already, but I'd recommend remagnetising your Wrenn Duchess. The magnets lose their magnetism over time, and it will experience a substantial drop in magnetism if the pole parts have been removed for cleaning. It should be able to wheel slip from stationary if power is applied suddenly. In terms of reflection of the period, you are right to use one of these as a reflection of the 30s-50s Dublo era. Unlike some other Wrenn locos, which had reworked chassis with sprung axles and other improvements (A4, Spamcan etc) the City is pretty much exactly the same as the Dublo City class from the late 50s in terms of mechanism. Generally, I wouldn't say there is too much of a difference in the running characteristics of prewar horseshoe motor vs a late one. The change of coarseness on the armature was to change the drive ratio for more scale running, but isn't a refinement as such. Servicing is key to these, as you mentioned, but they will crawl stunningly well on feedback controllers (TRAX or Gaugemaster HH etc)
Hi I am sure that will work but had you thought of just fitting a pair of small neodimium magnets to boost the magnetic field? They take up very little space and are very cheap.
It's just that's a really poor example. Wrenn was a cottage industry without the manufacturing facilities of meccano: dublo and wrenn are superficially identical, but the manufacturing of Wrenn was considerably worse. No one cares though people buy wrenn because it's a wrenn
I wish you had tested a loco with Hornby Dublo's flagship Ringfield Motor of 60 years ago used in a few of their last designs such as the West Country (Barnstaple), Castle (Cardiff Castle) and 08 diesel shunter. Compared with their standard motor these had really impressive performance though appearance wise their size resulted in them being obtrusive, especially in the cab of the Castle. In the 08 its performance is absolutely faultless
funny you say that: I've actually found that the smoothest and slowest start runners to be the 1/2". superb mechanism, not as powerful as the ringfield or 3/4", but beautiful runner
In the 1970s I designed and built thyristor contollers with simulated intertia and braking. Making it necessary to DRIVE the train. Otherwise you were going to overshoot. I ended up having to add a panic button to avoid damage in the hands of some incompetent "drivers". So it was possible to bring an engine up to a loaded train at a simulated 5mph and it wouldn't stall. In fact even with "magnadhesion" it could slip the wheels at this same speed.
The older models were built to last for a very long time unlike the models of today, detail and performance wise they are more than adequate regardless of how basic they are
Hi Sam, enjoyed your little history lesson, but also a bit concerned. I had a Hornby Dublo 3 rail set with Sir Nigel Gresley, Duchess of Atholl, an 0-6-0 and 2-6-4 tank engine. All die cast very detailed and good runners. Even now 70 years later I can see similar models on you tube still running well. I am not sure today’s Hornby locos will last that long! The Hornby motor you say has been in use for over 20 years only runs for 200 hours before needing replacement. It must be very cheap to produce after 20 years. The only part of the steam loco which must be expensive to make is the wheel set. This does not apply to diesel, diesel electric and electric models using simple bogies. Throw in a cheap plastic body and I reckon production costs per model for Hornby would be around £25 to £50 per loco! I understand why the move to plastic took place back in the day but surely not nowadays. When Oxford, a Hornby company can produce die cast detailed motor vehicles in a huge range for prices from £5 to £20, there is surely no justification for Hornby plastic locos. As far as I can see the only significant improvement in locos over 70 years has been DCC. It gives us multi train running, lights, sound, fire box flicker and even steam generation. Mind you this is done using elementary cheap chips which do not justify the prices being charged compared to the complex circuits in say a laptop costing £250 to £300. Er as much as Hornby’s latest range of locos. I don’t know much about Bachmann and other manufacturers but it seems to me Hornby is seriously overpriced and yet the company still seems to be struggling to make a profit. If it reduced prices and therefore sold a lot more perhaps it would become more sustainable. Seriously my main gripe is plastic. A move back to diecast would be much better for all us modellers and for the planet. And not just for locos but rolling stock would be much better and more realistic if made from other components.
The original Hornby engines had a three rail system, the centre rail being positive and the other two being the return. This meant that they were incompatible with the cheaper two rail systems. Eventually they saw the light and switched to the two rail but the cost of the engines didn't come down as they were precision engineered and were mainly die cast. Once Triang went into financial difficulties and were taken over by Hornby prices came down although detail was hit and miss.
Hornby Dublo were bought by Rovex Tri-ang and renamed Triang-Hornby. The die cast locos were still sold by T-Hornby, but under the Triang-Wrenn flag. Mecanno's Hornby Dublo went into liquidation as they were making quality models at set prices and couldn't compete with the very low price 'toy trains' made by Tri-ang. The latter were sold in Wooworths as sets at very low prices and thus sold many more sets than Hornby Dublo. They bought Mecanno at a knock down price in 1964!
Thanks for another interesting and well done video. It’s kind of funny but I’ve watched some other reviewers lately and it seems like most are trying to emulate you in their presentations and falling short in my humble opinion. Anyway as to your invitation on what I would like to see incorporated or offered on new model locomotives, For me simply smooth strong, quiet and reliable runners is the quality I appreciate most. So more of that please as well as a greater emphasis on quality control by the manufacturers. The detailing improvements I think are more easily achieved because of modern design and manufacturing techniques so that is nice to see also. Great job Sam!
That's very kind of you, many thanks for those kind words! You're absolutely right there - a focus on reliability and quality of mechanism would be very, very welcome! Thanks for watching, Sam :)
Just starting to get an interest again since childhood. Out of curiosity how well do these older mechanisms cope with pulse width modulated power supply as compared to the older stye power supplies?
Hi Ian, PWM seems to be fine with the older motors - I’m not too keen as it sounds unhealthy, but the smoother pwm supplies are fine (I use a gaugemaster with no issues)
hi Sam; Wrenn loco fascinating- that slow acceleration due to bulk seems in many ways very prototypical. It was fascinating to see! Regards the future- I'd love to see more metal used in construction, flywheels become ubiquitous, and prices come down for pure analogue users. Don't ever intend to use DCC, don't see why I have to pay for DCC compatibility! My dream would be a move back into live steam. The Hornby live steam mechanics seemed very sound, the issues (as per the 00 live steam club) were the controllers and the associated misleading instructions. Be fascinating to see you get your hands on a live steam locomotive one of these days! Cheers, and stay well, Chris
Thanks for the comment Chris! Yes I suppose the acceleration is quite realistic... but my kneejerk reaction is to get a bad feeling when I see that, as it means the motors are struggling. Live steam would be amazing - I'd love to see this come back too! :D Thanks for watching, Sam :)
@@SamsTrains I'm another that prefers that more realistic, slow, take-off to any other. At risk of sounding argumentative, (who, me?) I would say that a motor absolutely SHOULD struggle to persuade a hefty load into motion. It's that real battle of tractive effort over inertia AND the ponderous physics of all large steam engines that is the very essence of a realistic visual experience. ie, Even with zero load a heavy steam loco still accelerates relatively slowly. So a realistic model should never shoot out of the blocks like a rat up a drainpipe!
With DCC it's amazing how much better older loos can perform. My ringfiled locos perform almost as well as any modern loco, just need to optimise the BEMF settings a little. As for coreless, PLEASE let's stay with 5 pole. I detest the silly little low mass - low torque motors as much as DCC decoders do!
In my view the development of controllers, and especially DCC have had a major impact on running characteristics. I would like to see a video showing how DCC can be used to improve slow running and to simulate inertia etc.
The market seems to be flooded with diesels these days. As a steam buff, I would like to see more era 1 & era 2 steam loco’s as there were so many variations in design across the whole country. I am probably not the only person who thinks this, but diesels, in my opinion, are just characterless lumps of steel. If you go back back to Victorian and Edwardian times, engines were much more characterful and attractive. However, I would worry that manufacturers would use this as an excuse to charge exorbitant prices so I am not going to hold my breath in anticipation of any manufacturer taking me up on my suggestion. One can already see what I mean by style in the new Hattons 4 & 6 wheel coaches as they are very attractive in certain liveries and they did last a long time in railway service.
Great video I have examples of all those you talked about It’s really good for all your viewers to see just how much things have changed over the years Please do more historical differences videos
5 pole motors were fairly standard from the 1940's on. and of course the Boucher had their wonderful 21 pole motors. just that these models weren't in the cheap and common range, so are less seen and well known today, hence their complete absence from videos such as this
I also have about 26 wrens,only had 2 rubbish ones,one as spares,and the other one (although I got it working to a degree)went back,absolutely stunning(albeit) basic locos but beautiful running,Inc crawl,maybe I have been lucky?
Hey Sam, nice video, but quick question about the caledonian 812 at the end. Where were you able to find it? I really like that type of engine (mainly due to Donald and douglas) and I have been trying to find it for a while. Any idea where to find one?
They were made by Bachmann, exclusively for Rails Of Sheffield. Last I checked, all versions available had sold out, but I think some more were recently located in their warehouse, they may still have some in stock if that’s what you’re after.
Great video! Lima pancake motors are worth a mention if you want strong, dependable performance. Surprisingly smooth if carefully cleaned, serviced and with extra weights and pick ups. The majority of my diesel locos are all Lima from the 1990's.
You are right. Just run in a 'new' Class 26 this morning that has been sitting in my stock cupboard for the last 22 years and never been used. Runs like a champ after careful lubrication and 30 minutes on the track.
I do think the period 2000/01-2005/6 was something of a 'golden age' for model railways, Hornby in particular. We had reasonably priced, beautifully detailed and finished locomotives with well-designed mechanisms, quality motors and competent assembly. Things have changed, and not for the better. Today the prices are much higher and locomotives have become too complex and fragile to withstand everyday use. Also quality control and component choice seem to be very hit and miss and evidence of corner cutting often all too obvious. As Forest Gump might have said: 'Life is like a Hornby loco. You never know what you're gonna get'!
There would have been an additional bit of drag for the older trains; they used to have the power fed from a central rail, so extra friction as well as extra mass.
I just realized that the first locomotive has fully functional walschaerts valve gear, if you look close enough you can see the slide valve stem actually in good timing when going forward
It's quite awesome for the time isn't it? Great spot! :D
Thanks for watching, Sam :)
@@SamsTrains especially when most manufacturers nowadays don’t do those kind of details
Yes! The failure to reproduce that crucial characteristic of Walschaert's motion very seriously detracts from the realism of every modern OO gauge locomotive with which I am familiar. When a manufacturer clearly had the skill and miniature engineering resources to reproduce it so far way back when, I find it quite incomprehensible, actually unforgivable that not one of them (at least to my knowledge) is either capable or willing to provide that level of realistic detail today.
Otherwise, this was a very interesting presentation by Sam, as professionally articulate as usual! But I'm still not entirely satisfied with the slow speed performance of ANY model steam loco. There is definitely still room for improvement in the synergy of motor/flywheel(s)/gears.
@@John-Tropi I agree - Consistent and steady low speed (and crawl) is still an issue, and the high speeds are totally out of scale. I scratch-built a diesel-style loco and used a Chinese general-purpose motor with a built-in reduction gearbox, driving the wheels with a Meccano chain drive. The crawl speed was incredible.
@@SamsTrains Run better but not as durable as stock from previous decades
The can motor, flywheel, and gear tower mechanism in D5317 originated in the states. A company by the name of Athearn produced locomotive kits that came in blue boxes that used the first iterations of the mechanism. At first it was without flywheels, then they were added in the 70s Athearn locomotive releases.
Thanks a lot for sharing - that's really interesting :D
Thanks for watching, Sam :)
I started with the early Hornby diesels: one power bogie, and only it had current pick-ups, then Lima: Ringfield motor on one bogie only, but did have pick-up on both bogies. Which it needed as the fitted traction tyres lost some pick-ups. Neither ran very well. Now, I have Athearn-type mechanisms: all wheel drive and all wheel pick-up. By far the best solution for good running, and able to cope with momentary current loss on dirty rails, and through insulated point frogs.
In the 1970s I changed to N Gauge. I was quite upset with Rheumatoid running of my Lima AL6 (Class 86). It had a ringfield motor bogie one end with traction tyres and a pick only bogie at the other it wobbled when running and stuttered and stops at slow speed and only seemed to run properly at high speeds.
I went to an exhibition in Chester in 1970 and saw a layout using Minitrix locos. They had a central motor, 2 x universal joints, 2 x worms and two bogies with gear towers. These had 8 wheel drive and 8 wheel pickup, with excellent slow running and would pull 12 and 14 coach trains....I bought a class 27 for £7.30p. Although not used much now ( I have gone back to 00 now) it still runs, as all my Minitrix locos, as it di dY one. These are all 3 pole motors. Thanks to Bachmann leading the field, nearly all 00 diesel locos are like this now. N gauge seemed to lead the field long before 00. This was progress that made a great difference to running!
John Harrison. Wallasey, Wirral.
This motor design was used for several years. A lot were horseshow magnets, so did end up similar to the one you showcased. For the time, they were really great and exciting. The old half wave rectified controllers and battery controllers of the day were not quite as smooth as the newer controllers, but they do work better on full analogue controllers rather than modern electronic based controllers. I find the way they speed up slowly adds a bit of realism as real life locos don't go from 0 to full speed instantly. It takes time to get up to speed.
The very early plastics were acetate based and they warp and split so badly as they get old. Later plastics were a bit more stable.
I was auditor at palitoy in mainline days. Always used to buy one of each loco as ‘best’ but had a constant invite to delve in their scrap bin. For every three locos out of the bin I would recon on one good loco, one ‘useable’ loco and some scrap/spares.
Train at 22:45 truck looks to be off the track, still so smooth! Great video.
I noticed it too.
Dublo and Wrenn locos will give you a really good crawl with an H&M Clipper or Duette using the high resistance and /or half wave settings.
Ahh fantastic - I'll have to try this!
Thanks for watching, Sam :)
@@SamsTrains When I moved to California, 40 years ago, I brought my Hammant & Morgan controllers with me. What I found was that just upping the voltage with voltage converters didn't allow them to put out full power, so I replaced them with more recent American controllers. I found they worked perfectly with the old Hornby Dublo and Triang locos.
I no longer model, but back in the day (1980-2000) I became obsessed with slow running. It's the Achilles heel of smaller gauges and I drew up all sorts of designs using 5 pole motors with massive flywheels and huge reduction gearing. None of which came to fruition of course but all my locos were modified with pickups on all wheels etc. in a vain attempt to recreate the huge mass of the prototype. Very interesting walk through the history of OO loco design.
my gaiety tank with the factory 5 pole and 47:1 gearing actually ran worse at slow speed than the quality dublo 3 pole and 9:1 gearing.
I've thrown in that crucial word "quality" you'll note.
tbh, my example may have been really worn out, that mass of gears was very noisy, but it didn't really give those outstanding results that the mechanism would appear to promise.
and if it was worn out, would the same vintage dublo mechanisms be any better?
@@muir8009 Interesting!
Interesting video. I have a sizeable Dublo collection and am aways impressed how these still run 60+ years after they were made. The build quality is absoltuely bombproof and I imagine they will still be going strong in 2060. I wonder how today's offerings will fare in 20 years' time, nevermind 60 or even 100. As for features in the future, personally I would almost prefer fewer features and lower prices. The simplified approach that Hornby took with its 2-Bil and 2-Hal models seemed like a good one - they are decent looking models and pricing was very attractive.
I know they don't!
I helped rebuild the 'Mostyn Junction' layout at Wirral Transport Museum, Birkenhead. We bought numerous models old and new to run the layout.A lot of the new Hornby an Bachmann locos are on their 2nd and 3rd motors in the 15 years or so that the layout has been running with its own stock one Castle class loco had to have a new armature after being knocked off the track and left for an hour!
The other Dublo loco that stopped, one day of running, was stripped down and was found that one of the brushes had worn away down to the spring! These were probably the original brushes from the 1960s!!!
Long live Dublo!!!
John Harrison, Wallasey, Merseyside
I think the "dead rail" concept is fascinating. The locomotive is run by battery which could be charged by the track power & is remotely run.
I have a 1940s Hornby-Dublo Duchess of Atholl. The internals on that are pretty much identical to the Wrenn loco you demonstrated - even the magnet design and other details. Great model and still working after conversion to two rail pickup.
Later on I worked for Beatties of London ltd who stocked Hornby, Wrenn, Palitoy, Airfix and Lima alongside Fleischmann, Trix, Märklin Roco and Rivarossi. That experience opened my eyes to the vastly superior quality of the European manufacturers and models. Frankly the British outline stuff was rubbish, especially Hornby.
The European models were all superior runners, better made and detailed, and included features such as working lights that most British models were devoid of such as lights.
Mainline were the precursor to Bachmann. Airfix fell by the wayside eventually but had a good stab at it.
An interesting journey through the past. My time selling model railways was around 1974 to 1976.
It would be great to see you feature some vintage European models in a show.
VERY true, but Aunty Horny has come on in leaps and bounds, so this might no longer be the case.
Very interesting subject. The most interesting thing is that more than half a century old technical designs can still run beautifully on today's layouts with today's hardware! That's what i would call sustainability. We can't say so for way too many other things...
By the way I think the future of model railroading and also other modelling hobbies is 3D printing and DIY approach to making and fixing stuff. It can be more fun, more diversity in models offered, and also, more sustainable.
i like the heavy metal one, the lag in acceleration makes it look more to scale as it moves closer to the full sized .
A lot of trains from the 40’s were pretty clunky and more mechanical. Especially in the O gauge range. When I got a 1948 Lionel Columbia Scout for my grandfather, it was quite bulky, had exposed sprockets by the wheels, and was just an overall very bulky locomotive. But a cool one too!
Interesting video . The thing with model locomotives is I don't think they suffer from Planned obsolescence. So when it comes to modern locos it's all about development and what's available at the time. Simply it's just that when it comes to model railways products they have the opportunity to develop properly without being held back by Planned obsolescence.
Have you ever considered reviewing or purchasting a brass locomotive for your personal collection Sam? Many brass models are very highly detailed even by today’s standards and were produced in the 60s-80s
I never have, but I'd certainly like to one day - a very interesting breed of loco!
Thanks for watching, Sam :)
I appreciate towards the end when you acknowledge the limited nature of this video. The title is perhaps better than many other RUclips videos that have the vaguest of titles, often not really related to the video. So, 'A journey through time' may have people watching from an idea that it was more about a range of changes to model railways, including different gauges, the 'curious' three-railed models [that I could not relate to because of the lack of realism] to a fuller understanding of railway adhesion from real rail locomotion.
As a young child, my older brothers' 50's [UK] version of Triang-Hornby used 'Super Four'? rail track. My more realistic 60's 'System Six'? track, meant that my brother's shunter engine wheels' flanges 'knocked' on my tracks sleepers. Maybe DCC programs for a smoother acceleration from the start - I've never seen a real engine instantly accelerate to high speed. [I'm amazed though at how our real electric suburban rail in Brisbane, Australia can accelerate and decelerate at station platforms.]
My Australian version of an electric engine, in plastic, had a hollow area under the flooring for a heavy metal weight. Understanding better about real railway engineering and adhesion, even 'light rail' is still heavy, and necessary to keep rail vehicles in contact with the track. Today, with interests in real railway passenger and freight transport, I'd be interested in making my own N and/or Z scale track in closer to reality dimensions of track height and width - even though I'd need some good magnifying gear for my visual impairments.
Some 300 properties are to be 'resumed' - including my neighbours' houses for a new straight four-track rail corridor in Logan City, Queensland - focused on 'faster rail' between the Gold Coast and Brisbane for Australia's 2032 Olympic Games. It ignores the historical fact that we were proposed [standard gauge] interstate rail on this corridor about 120 years ago. Some parts of Australia can be called 'fifth world' today.
I was disappointed as a child of engines stalling, 'humming' and the 'jerky' movements. As model rail wagons and engines were often 'foreshortened', with curves much sharper than reality, I'd say that having models run at slower speeds and smoothly is necessary. I had already worked out for realism to change from the OO/HO gauges to N Scale was necessary for realism in a large room setting - or even Z scale. Unfortunately, I've gained long-sightedness and other visual impairment in later years - meaning I'd have to erect some small cameras around a diorama to see detail on a large screen today.
Currently, some parts of Australia are worse than UK's Dr. Beeching's Axing, causing some extreme neglect to people with disabilities in rural areas not having access to everything from appropriated medical care in large cities, going to the beach, nor seeing family and friends etc. Some of us die on terrible rural roads and truck-filled highways now.
So back in the 70 I don’t recall going slow . It was full tilt boogie . And if it went around a corner with the left or right wheels off the ground . You was doing it right
My Father always said that if one drove through a corner in a race car with all four wheels on the road, one isn't going fast enough and the suspension needs more engineering time, and driver needs more track time. If the vehicle was 'cocking it's leg' through a corner, then it is getting closer to being driven on the edge.
Before Mainline, they were AIRFIX GMR
(Great Model Railways)
I have thoroughly enjoyed your presentation. I have learnt a lot and I think your choice of models was excellent ! The close ups of the detail work is super. I clicked on your vid not knowing it is UK. But your information is pretty close to what is happening here in the US. Thank you for explaining the difference between 5-pole and coreless. Ever since Kato came out with coreless a few years ago I expected it to be "the revolution". Kato's interpretation is to put the motor right on top of the power wheels. I haven't seen any demos of their slow speed performance. Seems like that would be a tremendous freeing up of space for circuitry and speakers. Much success to you and I am happily subscribed.
The first Black 5's also had the first ringfield motors, I have one. Their valve gear also was borrowed from the "Britannia". To your end question, I have two " duchess" class that are 1977 & 1982 versions and had working lamps on the front, fairly weak, but they worked. Hornby could do that so much better now, it would atleast be nice if they revisited the concepts. Being from "Across the Pond" lights are standard on Locomotives. I'm not saying that ours are superior, I wouldn't be collecting and running UK prototype if I didn't like the "English" steam. And I'm the only one who works at my local hobbyists that can intelligently discuss UK prototype, thanks to shows like yours.
Interesting presentation. I would like to see this same sort of video done for USA locomotives, and for other European locos such as the Italian, the German, and the Austrian locos such as Roco. I'm particular interested in the tender drive developments in the Roco line
since about 1989 Roco also added too the tender drive a driveshaft from tender to loco (similar to Graham Farish oo) in some models, giving quiet loco + tender drive with good pulling power, don't know if they were the first to do it
31:13 i didn't think i would see the day where sam praises coreless motors
Hello Sam, I enjoyed your take on this and especially at the start of the video your note about compatible controllers etc. I am very much a vintage model railway enthusiast and am running all the early models you showed very successfully at scale speeds on my Tri-ang Super 4 based layout. These excellent models still have much to offer if you treat them to careful maintenance and of course there are period upgrades too, such as the superb five pole X03 / X04 Airfix motor conversion. Take care, all the best to you
Very interesting article! My main love is Hornby Dublo 3-rail - apart from the upright motor in the Duchess's and others they also made the first 'ringfield' magnet motors, in a couple of forms, with modifications. Very fine performers too! I also convert 'moderns' to 3-rail (a bit bonkers maybe but I started with a 3-rail set-up!!) and agree totally regarding the Mainline motors - they really aren't up to much are they! The Bachmann split-chassis locos run well but getting to the motor to wire in a 3-rail pick-up is a right pain! I have 3-railed a Bachmann Peak and that runs and pulls really well! Again I agree totally about the quality of the early 2000 Hornby locos, I have 3-railed a un-rebuilt west country and a princess and they are really superb runners. The Lima range is worth a mention too - their Deltic and class 40 are fine performers too, as is the small prairie, similar ringfield motors to Hornby.
I agree with the Lima small Prairie. I have one it's like a tank will pull anything you put behind it and could be thrown from a 10 storey window and finish in one piece
Yes, and the original ringfield motors were put into the locomotives of the Caste, 8F and Merchant Navy, not in the tenders. Unfortunately, they protruded into the cab.
remember dublo didn't use the first ringfield motors: just that the common and well-known dublo ringfield was produced before the common and well-known post dublo variety
We have sure progressed...sadly the prices have elevated to high pricing some are out of the budget of the average modeller
Sam. That looks like a G&R WRENN example, or Tri-ang/WRENN.
It is fitted with Tension-Lock couplings and has metal tyred, spoked, bogie wheels. HORNBY DUBLO ones had DUBLO/PECO TYPE and smaller bogie wheels.
Yours looks like 1966 on loco.
Loved the X03 in my Jinty. Never failed over 20 years. Bomb proof.
The reason we have OO/HO (1:76 scale bodies running on 1:87 scale chassis) is because the ‘best’ available motors were German but German locomotives were larger, so to accommodate the German mechanism in a British outline we adopted a slightly larger scale for the body.
Back in the 1960’s it was noticeable how much better the old 3-rail trains ran (well compared to my own Triang locos anyway) with fewer stoppages on spots of dirty track (these days with DCC we could add a ‘keep-alive’ supercapacitor to cope with dirty track). From memory the people at Pendon really drove the development of the coreless can motor. By the 1980s I was using N Gauge (having been given a Farish ‘train set’ in the late 1970s), not great, fitting additional pickups and adding weight made a big difference. The chap who popularised N gauge had to wind his own motors but they ran beautifully on his ‘in a violin case’ end-to-end model railway. I think the chap who built the H0 gauge Madder Valley (a personal favourite on display at Pendon) also wound motors for his own builds.
For the future I would like to see an inexpensive loco with DCC and the super-capacitor keep-alive added to provide decent running and the wider use of the Microtrains couplers to allow shunting (something I found a little frustrating with the old Triang ramp-between-the-tracks uncouplers). Once the customer has been hooked they would then likely invest in the more expensive but more detailed locomotives, although with a good running basic loco you could still have a lot of fun (see for example your own 3D printed engines).
Kids like ‘operating features’, opening doors on wagons and vans, container cranes that actually lift containers on and off wagons and conveyors and silos to load coal and aggrigates. One thing I experimented with years ago was to use the small programmable sound discs made for ‘singing’ Christmas cards to add the sound of carriage doors slamming (although that sound is probably before your time), you need at least two, one for lots of doors on an express or commuter run and another with just a few for the quieter periods, they will fit comfortably under the platforms and can be controlled by a simple battery and push button set up. That sort of thing is harder to find these days and finding a user-programmable one is very difficult.
Sam. I have had Hornby Dublo from 3-Rail days. Some of the first loco'swere a bit notchy, but some later models had the Meccano/Dublo (loco driven)Ring Field motor. This was very large, long motor, but much smoother than the originals. One of the best of these was the the re-built West Country loco. This was produced as Dorchester and Barnstable. One was 2-Rail, the other 3-Rail.
I have a 2-rail one and is 3-pole, but is so well geared that it will double head with a modern Hornby 'Battle of Britain' and even crawl at similar speeds. This is a much heavier model and will pull more than its modern equivilent.
In regard to the early Tri-ang locos, try them with the controllers of the time! In comparison to the Dublo, there really is none!!! They were cheaper. That is the only good thing you can say about them, also they made more popular loco types than Hornby Dublo (in my opinion, of course). Tri-ang had oversize flanges and cast mazak wheels that were not plated so didn't pick up very well without constant cleaning. These will not even run on code 100 track as the flanges bounce over the track chairs! The valve gear on Dublo locos was simplified and over size, but Tri-ang's, what there was of it, was also and 'very' simplified.
Also with Tr-ang the buffer height was about 1/8"/ c.3.5mm too high on allthir models. Dublo's models were scale height!
If you put a Dublo loco next to drawings, they were, in general, scale size. 2 Dublo locos were not; one was their N2, which was similar, but not an actual copy and their Deltc loco. So I have been told, this was built from 'memory' after the designers had been shown the real loco being built. They got it very wrong and the model was very much too short!
It did have a very powerful ringfield motor bogie and die cast body, it also came out, I believe, before the real loco!
Unfortunately, their coaches were flush glazed, but short on length too with lithographed printed details.
Tri-ang loco's were nearly all too high above rail level and a lot were very short. The Princess was about an inch too short compared to the modern models. Their 1960s mk1 coaches were scale length, but not flush glazed until the late 1980s and still about 3.5mm too high above the rails.
Tri-ang motors used 2-start worms on their motors which made them start at about 40mph and had a top speed of around 130mph!!!
To conclude, there really wasn't any comparison between Dublo and Tri-ang. Dublo was far supreme in detail, weight, pulling power and scale.
If anybody comments about Dublo to me, I tell them about the pulling power of the Dublo 8F 2-8-0. I once ran a thirty five coach train of mark1s on the 'Mostyn Junction' layout at Wirral Transport Museum, Birkenhead. The 8F was slipping a little on curves, but pulled the train, consisting of Triang-Hornby, Mainline, and Hornby mk1 coaches for about an hour!
When first introduced, this model pulled a 3 year old child on a special display track at that years Model Engineers Exhibition, showing the power of the ringfield motor in the loco!
I hope this rant will be educational to you and hope you try out and compare a Hornby Dublo Barstable loco to a modern Hornby one.....You'll be very surprised!!!
Best wishes and keep up the good work.
John Harrison. WALLASEY, WIRRAL.
FYI it seemed me they used to have these "pulse power packs" that allowed the old school locomotives to run more prototypically at low speeds.
Back then it was half wave rectification with metal plate rectifiers and variable resistors to create voltage drop. No semiconductors to give thyristor control let alone feedback circuits. Many DC controllers still use 1930's output waveforms though!
H&M High resistance and full wave settings work much better on Dublo and Wrenn locos
13:10 Hornby-Dublo developed the ringfield motor back in the 1960's. I have a couple from 1962, and they do run very well, but the controllers were more powerful for all the weight and current needed to pull long trains back then.
Am I the only one who noticed that the Bachmann diesel at 22:00 had a wheel off-track? Set my OCD off something fierce, thanks Sam! :)
Great video though!
Was the ring field motor derived from a similar German one? I seem to remember reading about it but I'm not sure.
Yes, I think they copied a Fleischmann design. It would probably mean a court case due to breach of copyright today.
The original battery powered Rovex 'Princess' with 2 coaches plus track was my first trainset with the loco current collection being from 2 sprung brass plungers that came out of the body under the front of the firebox. The one you are looking at is a later one! I have no idea what material these original train sets were made of but in time the whole lot started to 'curl' and distort. Including the battery/ controller box which contained 2 or 3 Ever-Ready 'front bike light' double batteries. Unfortunately, in time, the battery box distorted so severely that the trainset became unusable as an electric one so it became a push-a-around the oval job with the 2 short coaches and loco hobbling and derailing beacause the all wheel tyres on the set had developed grooves and the coaches assumed a U shaped form. Just like the rest of the train set! However, one day when I licked the tender body with the tip my tongue so I could stick something on it's side there was a strange burning like sensation on the tip of my tounge! Talk about toxic toys! I can assure you I have never, ever, licked a train set since!
what a cool first trainset: back when it was perfectly fine to run a 2 or 3 coach euston express hauled by a stunted princess, around a mass of track. in all honesty, I think with our current fixation on almost photographic reproduction of a particular time and geography we've lost the ability to just enjoy a model railway as a model railway. one still can of course, but one gets categorized by others who consider what they do is the "correct" way, completely overlooking that essential factor of "who cares?".
on a slightly more constructive note the early plastics were an acetate (same as film stock) which caused the warping and mis-shapeness, progressively changing over to polystyrene from the late 50's
That Royal Scot is actually the version Palitoy produced initially for their Airfix GMR range. It was markedley different from the one produced for the Mainline range - different body mouldings, different chassis and motion gear, different finish, too. The Airfix ones initially went to Dapol, with a couple of Dapol originals and most of the erstewhile Airfix GMR range eventually going to Hornby - the Scot in the vid being discontinued due to it's rather grouchy chassis. The (different) Mainline branded one and it cousins the Jubilee, the re-built Patriot and the 'parallel' Scot did indeed become the backbone of the initial Bachmann Branchline catalogue - though as I've mentioned above, these quite different from the Scot in video, it being the Airfix GMR version. Great vid though, Sam.
I've got models from my own country produced in the 80ies and onward and it's fun(ny) to see the development of various manufacturers when opening them up and seeing how it was first all analogue focussed with track pickup at various points, to 8-pin DCC ready but still using just 2 mini light bulbs with light guides to both ends, to LED use and 21/22 pin connectors.
Sam - great video. At the end you asked what more would we like to see on model locos. The answer is LESS not More. From my perspective, as a modeller and operator, rather than collector, I would like to see dimensionally accurate but less detailed locos at a cheaper price. More like the Hornby Railroad. In that way we can customise and detail ourselves which is a big part of the hobby. I would also like to see modern mechanisms being made available by the likes of Hornby and Bachmann so we can upgrade older models at a reasonable cost and without having to resort to making our own mechanisms.
A model railway company in America supply three different qualities of loco at 3 different pricing points: Museum Quality, Rivet Counter Quality and Operator Quality. It seems to me that is something the manufacturers of British trains should consider.
Interesting video, thanks a lot Sam. The Wrenn locos were generally smooth and really powerful. I would suggest that the reason your Duchess is a bit sluggish is because the motor need remagnetising which is fairly easy to do, and understandable after decades. The advent of plastic and nylon in mechanisms has been both an improvement and a backwards step.
Thanks very much John - I re-magnetise all of my vintage motors as part of my servicing, so the magnets are fine
Thanks for watching, Sam :)
A Super NEO magnet replacement is recommended to rectify this!
With the good old Dublo and Wrenn locos the sluggishness and worse was usually down the the magnet losing its magnetism and also lazy maintenance with the oil can. There are super magnets available to replace the old ones available on ebay. My first loco was a Duchess of Montrose which would have been 63 if fatigue and not so gentle treatment. The old Rovex would have died much sooner. I bought my HD Barnstable in 1967. It is play worn with only new magnets and driving wheels being replaced in that time. Like all locos of that era 200 mph was the standard express speed as their controllability was sort of limited. Speed drop off on inclines was formidable however these locomotives were huge fun to play with and still are. Stuff realism.
Replace magnets with Super NEO types and you will see a miraculous improvement in running!
Thank you, i will follow that up with some of my other HD locos that are in need of livening up.
I honestly hope that in the future, they stop using pick-ups on the engines. Battery-power or rechargable batteries fitted into the locomotives could give a much more constant flow of electricity to the motor, which would relieve the need to constantly clean the track, or such things as praying for your smaller engines to get over the express-points. I realise all of this would probably mean radio-control, but honestly, that doesn't seem like a bad thing.
No more worrying for what's DC or DCC. Just pure undisturbed control.
Ain't that a thought? :)
That's an interesting idea! The problem is that everyone with a OO railway already uses electrified rails and has a controller... any manufacturer who goes against that risks putting off the vast majority of their potential customers. With how niche the hobby is, I think we're too deep down the electrified rabbit hole to ever return
Thanks for watching, Sam :)
radio control sounds sodding awful, and just use live frog points, the east Germans had been using plug and play no issues live frog points since the mid fifties: hornby dublo should've had a look at what other manufacturers were doing with points design when they went 2 rail
Couldn't afford a tomix set sooooo decided to make my own... Hasn't that been fun lol... First attempt at running it just wanted to torque of the track then the shafts vibrated out.. had to get rid of some play so I don't throw my drive wheel If it bound at all.. now I just need to get rid of the play in the carriers axles as I kept jumping the track.. now I'm trying to decide whether to coat in dielectric coating or di tape.. or pain staking wire laying on the edge of the track.. or over hang like some trains trams etc ...the fact I even have it operational in a day I was stoked for $20 work 🙄👍
Also you said that you had upgraded a lot of the tender driven Hornby engines to better quality motors A video on that would be most interesting
I did a video on those conversions - hopefully you can find it on the channel!
Interesting, the development from my early days (70's) through till now does show improvement which is great.
It would be interesting to know more about your DC-controllers: Are they controlling the DC-voltage or do they have a pulse width modulation (PWM) which would improve slow motion movements highly?
Worm-based transmissions save a lot of space, they could replace several pairs of gear. But they are prone to wear so they are used rather in toys than in real world applications. Models with a worm-based drivetrain have a different braking dynamic than those without it. Worms are unable to transmit forces from the wheels to the motor, so the dynamic just depends on the rotating masses before the worm, in result the rotor in the motor and a flywheel if present. So the bigger mass of a metallic housing does not help.
The German brand Fleischmann used to have the "Rundmotor" for decades, a relatively slow turning motor which allowed them to avoid worm-based transmissions and use very simple gear transmissions easy to maintain. Märklin used to have a similar positioned motor.
You've completely omitted Trix Twin and Graham Farish. Graham Farish put the motors in the tenders of tender locomotives, and drove the locomotive driving wheels through a drive shaft and gears. The motors regularly burned out, so people just replaced them with the Triang X04, which was easy as they just had to be attached to the drive shaft.
Trix Twin were originally AC 3-rail, with enormous wheel flanges and crude bodies. In the 1970s they came out with a range, mainly LNER Pacifics, that were as smooth as any modern locos and much more detailed than their previous range.
You forgot to mention that the pre-war Hornby Dublo range was 3-rail. The 3-rail wheels had an enormous rolling resistance, so you would be lucky to get your loco to pull more than two coaches. The Wrenn model that you showed was based on the Hornby Dublo 2-rail version, which had plastic tender and bogie wheels, and a plastic tender body, so it was not a good representative of Hornby Dublo in the early 50s. Most locos in those days shot off like a rocket the moment you turned on the controller. The H/D Duchess locos and A4s were renown for that. I don't know why the one you had was so sluggish to start.
Several of the more modern locos that you showed were very jerky: a lot more jerky than the Hornby Dublo locos were.
Don't get confused by the term "Ring Field Motor". The first locos to be fitted with ring-field motors were the H/D Castle, 8F 2-8-0 and Merchant Navy, and the motors were IN THE LOCOMOTIVE, NOT TENDER. They went on to use them in the Diesel Shunter and the Deltic.
You completely omitted the Airfix range, which, like Triang-Hornby, put motors in the tender of tender locos.
Superb video. It was mainly the motors. I replaced my Triang Jinty with a modern 24v motor and a nylon worm and it runs like a Kato or Fleischmann loco now. I also have a 1940 HO Gilbert-American Flyer loco and again if it had a different motor it would run so better. One more thing, Hornby tender drives was a backwards step from what Triang offered. You are right too about controllers. They are amazing now compared to what was around in the past.
Ahh fantastic idea - I've been meaning to try something similar myself - you've set me on now! :D
Thanks for watching, Sam :)
@@SamsTrains I can't wait! You can see the Jinty in this video along with some other 24v motor and nylon conversions.
ruclips.net/video/_vwsHd1FnVY/видео.html
Will you be doing any more reviews of older locos such as those from Lima, Triang, Wrenn etc?
I think a review like that will be good
The one thing that I will add in here which of course it was reflected in the prices of the items at the time
But the hornby dublo duchess models were very good in model terms. Dimensions were good with modeled valve gear and multiple small details. When they run they look like a miniature version of the real thing
The early tri ang models were more of a toy with very little for details and valve gear, plus it physically looks like dimensions are off, they don’t have the sleek look that real locomotives or even hornby dublo had
The tri ang had the price going for it which is why they became the big company as time went on
But as far as the actual models go and the functionality I find that hornby dublo did a lot better job of actually capturing the real life versions
That's a good thought - would have been very interesting to compare those! Thanks for sharing your thoughts, and certainly true that Tri-ang were much cheaper!
Thanks for watching, Sam :)
A very interesting video i would like to see more like this, well done Sam.
Thanks so much - I'll see what I can do! :D
Thanks for watching, Sam :)
I had a Hornby Dublo kit from the late 1950's and early 60's. I had a controller that received its power from a second-hand lionel box. It had a Canadian Pacific loco and caboose. It was the version of rails with the tin-plate base and center power rail. I purchased the mail car set with my own money. On a visit to Britain in 1961, I received a second loco with the ring field motor. The only thing that I remember about that loco is that it would not run on my layout. I'm not sure what the issue was. Power supply being 60 hz? I'm not sure.
I also got a second controller that was complete with transformer built in to plug into 120 volts split phase. (Split phase took the output of 240 volt supply and used a central neutral to give 120 volts on each side of the neutral. So a electric "range", dryer or water heater would operate on 240 volts.)
In your review you did not cover the merger in the 60's of Hornby and Triang. That seems to be when Hornby started using the triang style coupler. (That seems to be the de-facto coupler for U.K. model railway use. North American trains use a different style, with an alternate style called the KD coupler being available as an after-market upgrade.)
I have a Flying Scotsman train set dated 2006. The loco has a 5 pole Ringfield motor and runs beautifully, as good as my new Princess Royal and Princess Corination locos - maybe I am lucky?
Probably not just lucky! The 5 pole ringfields were a big improvement in performance... but they are quite rare; implemented just before they ditched the mechanism completely... so you're certainly lucky in that sense!
Thanks for watching, Sam :)
Thanks Sam, great video! As for additional features why don't Bachmann fit tender pickups to all their steam locos not just some of them!
That’s a good question - I can’t believe they don’t always do that either!!
@@SamsTrains I have added my own pickups to Bachmann steam loco tenders where I have bought second hand but I avoid buying new Bachmann steam locos that don't have tender pickups.
Most don't need them.
I have the same Pannier tank from that era and when I brought it off eBay it ran as smooth as butter, it was shockingly superb, even the crawl was impeccable. However I dropped it and some parts fell off so it doesn't run as well
Most enjoyable history lesson, Sam. at 22:12 one pair of wheels is off the track! But it still goes. Why is that?
Every locomotive has multiple power pick-up points, so one pair of wheels being derailed doesn't stop it from moving.
That 70's class 9F Evening Star was my first model train! Glorious to see one still going strong. I remember it being super powerful, to the point where I could get it to wheel spin when starting under full power, and it could pull as many coaches as I could afford to put behind it at the time. Didn't like crawling at all though. Great train for the day.
I remember seeing them at exhibitions with wobbly tenders, caused by traction tyres, and sticking valve gear and wheels static and still being pushed, sliding, along the track....Horrible!!!
I had a Black 5 (tender drive) tha was awful. I fitted an X04 motor to the loco and replaced the traction tyre tender wheels with solid metal ones and wired the two motors together. The tender wheels did slip a bit as they rotated faster than the X04 in the loco but pulled 3 times as much stock, without the tender wobble and did not stop over any dead frog points!
What I didn't hear in your review was whether the trains performance modeled the train of which is a model. My philosophy is I want a train that reflects what it represents, not to win a drag race.
Interesting retrospective Sam ! And I remember the first Märklin loco's I bought in the early 70's. All Die-cast and the motors were not that bad but not with slow speeds as today. I changed to 2 rail DC and since 2014 DCC and there we look at more refined performances in the speed spectrum. Not to mention the sound. Looking back just one 'generation' and O boy what a difference ! My dream loco's: onboard power for HO and OO scale. No dirty track worries and easier to build layouts without all the wiring and polarity issues on points. With the smaller and more efficient motors it's maybe not that far off. Thanks for sharing !
A great summary of 00 model developments over the ages. I had an early Dublo N2 with a horseshoe magnet, which had much less power than the standard 1960s N2. I don't think we even tried to make our locos crawl back then; we were grateful to have any speed control! - just try getting a clock-work loco to crawl...
Graham Farish produced some 00-gauge locos and stock in the 1950s, using early plastic: good detail for the time, but if you were not careful, the wheel flanges would break off. Their King class loco had a weird motor, with a rotating armature consisting of the permanent magnet, surrounded by electromagnetic coils energised by an arrangement rather like the 'points' in a 1950s car distributor! That was in the tender (with plunger pick-ups); a flexible drive shaft to the loco enabled the driving wheels to do the work. Again - crawl it did not: you had to turn the controller full on to get it to start moving!
Those Graham Farish motors were renown for burning out, so most people replaced them with Triang X04 motors.
In terms of electronics, keep alive (for DCC) should be standard on every loco.
Enjoyed the video a great deal. As for core-less motors we were using them back in the very early 1980s with portescap RG4
@22:00 45114 the left hand bogie's wheels are off the track (Rolleye's)
I am 61 years old and have my Uncles Lionel Locomotive and tinder with smoke cir. 1940 the engine is easy as heavy as a red clay brick, cast iron , still runs.
Great Video Sam. Thanx for the Education.
As I was born In 1956 my first Loco was a Triang Black Princess and The O8 Shunter quickly after..!
I lost most of my Train Set in the Move to Oz. In 1980. Damn it..!
But Started again at the Birth of my Son..!
Great Video. Cheers All.
Kim in Oz. 😎
Great review. I remember those X03/X04 motors - they used to emit a characteristic ozone smell when they ran. I would like to see the manufacturers fit as standard, much more realistic and functional couplings - those tension-lock types are ugly and useless and don't match the huge improvements in accuracy achieved in other areas of the models.
I loved that smell!
Absolutely. At the very least, that all of the companies make compatible Tension Locks - the current ones are subtlety different and come apart if two different types are coupled together.
Seeing the evolution and changes to engine solutions over the years is quite fascinating.
Thanks for sharing. 😉👌🏻
I had an early Hornby Dublo train set. This was three rail (centre rail live) running. Some models ran better than others. My basic set was second hand, and had early die-cast metal locos. The best runner was A4 Sir Nigel Gresley in LNER garter blue. Metal die-cast body. A later addition was an LMS Duchess class - Duchess of Hamilton. Plastic moulded body and, while a reasonable runner, didn't have the pulling power of the A4. Don't remember much about the motors as I only gave them the occaisonal run. The layout covered the entire floor of the front room and my mum didn't like me getting it set up! When Hornby introduced Dublo they thought they could make everything "half 0" scale. But early eletric motors could not be sourced that small. Forcing them to build the locos and rolling stock in 1/76 scale. They had, apparently, already produced track in the HO scale (1/87) and could not aford to scrap it all and start again. So Dublo trains ran on HO scale track in their sets. Hence the instability over tight curves of models running at too high a speed.
the early hornby dublo were very well engineered and a robust lot weren't they? regarding the availability of electric motors that was all a bit of a myth, especially the fact that hornby designed their own and would've designed any to fit the working area. hornby hadn't actually made any track previously: the tinplate track was of course based on the proven marklin design. the 4mm to 1ft was of course just a leftover from bing, and it worked and allowed for the real reason of the narrower than scale gauge: axle boxes, always an issue for many years
Good on ya Sam gr8 informative video there m8 thankyou.
Cheers from John in Australia
All the Hornby early Silver Seal locos had the early six wheel drive Ringfield motor.... 9f, Black 5, Britannia and the original two tone green 47 Sampson.
Excellent video Thank you for it. One note: the motor type you show in 11:21 (or in 19:35) is not a CAN motor but according to your own video it is a "square bare motor" (Block motor in German), very popular in 1964. A CAN motor (like in 23:40) is usually a cylinder shape with a metal coating. This does not remove any of the qualities of your video. I wish an equivalent was made for Märklin locos (a very rich subject).
Strangely you mention Hornby golden era (for motors & transmission) being in 2000, for Märklin this golden era was in 2004 with SDS (Soft Drive Sinus) motor, tiny, ball-bearing-mounted, helicoiday winding, no-collector (rotating field), total silence. Alas this was phased out after Märklin filed for bankruptcy protection in 2009
Dear Sir,
This was a very innovative and interesting video. I probably knew all of the shown engine generations (not personally, though), but have not seen them before in a evolutionary, cronological presentation.
Cheers from Brazil!
Thank you very much fort the kind words Eugenio, glad you enjoyed the video!
Thanks for watching, Sam :)
Try remagnetising the magnet in the old hornby LMS City.
13:18 I've just restored one of the very early one of these with the original ringfield!
Hi Sam, Sadly, I need to correct you. Palitoy didn't directly become Bachmann. After the Palitoy "mainline" brand, you had Airfix ,GMR & Replica Railways all releasing the same models before Bachmann took over the molds. All they did was to have slightly better motors whilst still using the split chassis. I remember the joke about the Palitoy/Airfix/GMR models was, great detail BUT if you got a good runner you were very lucky!
I don't think Sam referenced Bachmann coming DIRECTLY after Palitoy
Others may have said this already, but I'd recommend remagnetising your Wrenn Duchess. The magnets lose their magnetism over time, and it will experience a substantial drop in magnetism if the pole parts have been removed for cleaning. It should be able to wheel slip from stationary if power is applied suddenly.
In terms of reflection of the period, you are right to use one of these as a reflection of the 30s-50s Dublo era. Unlike some other Wrenn locos, which had reworked chassis with sprung axles and other improvements (A4, Spamcan etc) the City is pretty much exactly the same as the Dublo City class from the late 50s in terms of mechanism.
Generally, I wouldn't say there is too much of a difference in the running characteristics of prewar horseshoe motor vs a late one. The change of coarseness on the armature was to change the drive ratio for more scale running, but isn't a refinement as such.
Servicing is key to these, as you mentioned, but they will crawl stunningly well on feedback controllers (TRAX or Gaugemaster HH etc)
Hi I am sure that will work but had you thought of just fitting a pair of small neodimium magnets to boost the magnetic field? They take up very little space and are very cheap.
It's just that's a really poor example. Wrenn was a cottage industry without the manufacturing facilities of meccano: dublo and wrenn are superficially identical, but the manufacturing of Wrenn was considerably worse. No one cares though people buy wrenn because it's a wrenn
I wish you had tested a loco with Hornby Dublo's flagship Ringfield Motor of 60 years ago used in a few of their last designs such as the West Country (Barnstaple), Castle (Cardiff Castle) and 08 diesel shunter. Compared with their standard motor these had really impressive performance though appearance wise their size resulted in them being obtrusive, especially in the cab of the Castle. In the 08 its performance is absolutely faultless
funny you say that: I've actually found that the smoothest and slowest start runners to be the 1/2". superb mechanism, not as powerful as the ringfield or 3/4", but beautiful runner
The 08 had a better more realistic low top speed and outside cranks unlike the Tri-ang and Triang-Hornby version's.
In the 1970s I designed and built thyristor contollers with simulated intertia and braking. Making it necessary to DRIVE the train. Otherwise you were going to overshoot. I ended up having to add a panic button to avoid damage in the hands of some incompetent "drivers". So it was possible to bring an engine up to a loaded train at a simulated 5mph and it wouldn't stall. In fact even with "magnadhesion" it could slip the wheels at this same speed.
Happy someone does this
The older models were built to last for a very long time unlike the models of today, detail and performance wise they are more than adequate regardless of how basic they are
That's certainly true - they did last back in the day!
Thanks for watching, Sam :)
Hi Sam, enjoyed your little history lesson, but also a bit concerned. I had a Hornby Dublo 3 rail set with Sir Nigel Gresley, Duchess of Atholl, an 0-6-0 and 2-6-4 tank engine. All die cast very detailed and good runners. Even now 70 years later I can see similar models on you tube still running well. I am not sure today’s Hornby locos will last that long! The Hornby motor you say has been in use for over 20 years only runs for 200 hours before needing replacement. It must be very cheap to produce after 20 years. The only part of the steam loco which must be expensive to make is the wheel set. This does not apply to diesel, diesel electric and electric models using simple bogies. Throw in a cheap plastic body and I reckon production costs per model for Hornby would be around £25 to £50 per loco! I understand why the move to plastic took place back in the day but surely not nowadays. When Oxford, a Hornby company can produce die cast detailed motor vehicles in a huge range for prices from £5 to £20, there is surely no justification for Hornby plastic locos. As far as I can see the only significant improvement in locos over 70 years has been DCC. It gives us multi train running, lights, sound, fire box flicker and even steam generation. Mind you this is done using elementary cheap chips which do not justify the prices being charged compared to the complex circuits in say a laptop costing £250 to £300. Er as much as Hornby’s latest range of locos. I don’t know much about Bachmann and other manufacturers but it seems to me Hornby is seriously overpriced and yet the company still seems to be struggling to make a profit. If it reduced prices and therefore sold a lot more perhaps it would become more sustainable. Seriously my main gripe is plastic. A move back to diecast would be much better for all us modellers and for the planet. And not just for locos but rolling stock would be much better and more realistic if made from other components.
Here here!!!
The original Hornby engines had a three rail system, the centre rail being positive and the other two being the return. This meant that they were incompatible with the cheaper two rail systems. Eventually they saw the light and switched to the two rail but the cost of the engines didn't come down as they were precision engineered and were mainly die cast. Once Triang went into financial difficulties and were taken over by Hornby prices came down although detail was hit and miss.
It was Hornby that got into dire financial difficulties and the name bought by Triang to become Triang-Hornby
Hornby Dublo were bought by Rovex Tri-ang and renamed Triang-Hornby. The die cast locos were still sold by T-Hornby, but under the Triang-Wrenn flag.
Mecanno's Hornby Dublo went into liquidation as they were making quality models at set prices and couldn't compete with the very low price 'toy trains' made by Tri-ang. The latter were sold in Wooworths as sets at very low prices and thus sold many more sets than Hornby Dublo. They bought Mecanno at a knock down price in 1964!
Nice to see some of those older locos
Thanks Sam
Funny you mentioned a Mainline Warship. Gave up with mine took the motor out and it runs as a dummy with my Lima/Bachmann Warships. 😄
Thanks for another interesting and well done video. It’s kind of funny but I’ve watched some other reviewers lately and it seems like most are trying to emulate you in their presentations and falling short in my humble opinion. Anyway as to your invitation on what I would like to see incorporated or offered on new model locomotives, For me simply smooth strong, quiet and reliable runners is the quality I appreciate most. So more of that please as well as a greater emphasis on quality control by the manufacturers. The detailing improvements I think are more easily achieved because of modern design and manufacturing techniques so that is nice to see also. Great job Sam!
That's very kind of you, many thanks for those kind words! You're absolutely right there - a focus on reliability and quality of mechanism would be very, very welcome!
Thanks for watching, Sam :)
Just starting to get an interest again since childhood. Out of curiosity how well do these older mechanisms cope with pulse width modulated power supply as compared to the older stye power supplies?
Hi Ian, PWM seems to be fine with the older motors - I’m not too keen as it sounds unhealthy, but the smoother pwm supplies are fine (I use a gaugemaster with no issues)
Full wave controllers are much better for the older locos, especially Dublo and Wrenn.
hi Sam;
Wrenn loco fascinating- that slow acceleration due to bulk seems in many ways very prototypical. It was fascinating to see!
Regards the future- I'd love to see more metal used in construction, flywheels become ubiquitous, and prices come down for pure analogue users. Don't ever intend to use DCC, don't see why I have to pay for DCC compatibility!
My dream would be a move back into live steam. The Hornby live steam mechanics seemed very sound, the issues (as per the 00 live steam club) were the controllers and the associated misleading instructions. Be fascinating to see you get your hands on a live steam locomotive one of these days!
Cheers, and stay well,
Chris
Thanks for the comment Chris! Yes I suppose the acceleration is quite realistic... but my kneejerk reaction is to get a bad feeling when I see that, as it means the motors are struggling. Live steam would be amazing - I'd love to see this come back too! :D
Thanks for watching, Sam :)
@@SamsTrains I'm another that prefers that more realistic, slow, take-off to any other. At risk of sounding argumentative, (who, me?) I would say that a motor absolutely SHOULD struggle to persuade a hefty load into motion. It's that real battle of tractive effort over inertia AND the ponderous physics of all large steam engines that is the very essence of a realistic visual experience. ie, Even with zero load a heavy steam loco still accelerates relatively slowly. So a realistic model should never shoot out of the blocks like a rat up a drainpipe!
With DCC it's amazing how much better older loos can perform. My ringfiled locos perform almost as well as any modern loco, just need to optimise the BEMF settings a little. As for coreless, PLEASE let's stay with 5 pole. I detest the silly little low mass - low torque motors as much as DCC decoders do!
In my view the development of controllers, and especially DCC have had a major impact on running characteristics. I would like to see a video showing how DCC can be used to improve slow running and to simulate inertia etc.
The market seems to be flooded with diesels these days. As a steam buff, I would like to see more era 1 & era 2 steam loco’s as there were so many variations in design across the whole country. I am probably not the only person who thinks this, but diesels, in my opinion, are just characterless lumps of steel. If you go back back to Victorian and Edwardian times, engines were much more characterful and attractive. However, I would worry that manufacturers would use this as an excuse to charge exorbitant prices so I am not going to hold my breath in anticipation of any manufacturer taking me up on my suggestion. One can already see what I mean by style in the new Hattons 4 & 6 wheel coaches as they are very attractive in certain liveries and they did last a long time in railway service.
Remember the same motor as in the pricess in old scaletrix cars!
Great video
I have examples of all those you talked about
It’s really good for all your viewers to see just how much things have changed over the years
Please do more historical differences videos
Really enjoyed this Sam. Well presented. Only just came up on my suggestions
fun fact i own a 1997 Athearn US diesel (GE 9-44CW) witch has allwheel drive (6 axels) and a 5 pole motor
5 pole motors were fairly standard from the 1940's on. and of course the Boucher had their wonderful 21 pole motors.
just that these models weren't in the cheap and common range, so are less seen and well known today, hence their complete absence from videos such as this
I also have about 26 wrens,only had 2 rubbish ones,one as spares,and the other one (although I got it working to a degree)went back,absolutely stunning(albeit) basic locos but beautiful running,Inc crawl,maybe I have been lucky?
looks like your class 45 had a minor derailment on one of its wheels
Hey Sam, nice video, but quick question about the caledonian 812 at the end. Where were you able to find it? I really like that type of engine (mainly due to Donald and douglas) and I have been trying to find it for a while. Any idea where to find one?
They were made by Bachmann, exclusively for Rails Of Sheffield.
Last I checked, all versions available had sold out, but I think some more were recently located in their warehouse, they may still have some in stock if that’s what you’re after.
Great video! Lima pancake motors are worth a mention if you want strong, dependable performance. Surprisingly smooth if carefully cleaned, serviced and with extra weights and pick ups. The majority of my diesel locos are all Lima from the 1990's.
You are right. Just run in a 'new' Class 26 this morning that has been sitting in my stock cupboard for the last 22 years and never been used. Runs like a champ after careful lubrication and 30 minutes on the track.
I do think the period 2000/01-2005/6 was something of a 'golden age' for model railways, Hornby in particular. We had reasonably priced, beautifully detailed and finished locomotives with well-designed mechanisms, quality motors and competent assembly. Things have changed, and not for the better.
Today the prices are much higher and locomotives have become too complex and fragile to withstand everyday use. Also quality control and component choice seem to be very hit and miss and evidence of corner cutting often all too obvious. As Forest Gump might have said:
'Life is like a Hornby loco. You never know what you're gonna get'!
There would have been an additional bit of drag for the older trains; they used to have the power fed from a central rail, so extra friction as well as extra mass.
I just bought around 50 used old engins from the 90s i guess in Japan.