Cheers for the video, just wondering, do you not need to disconnect the negative terminal on battery before hardwiring camera? And would it be the same in the Hybrid?
I've been studying this mirror assembly. Compared to the OEM mirror, it sits very close to the roof line when installed. Where the original has a straight stalk, the replacement has a two part canted stalk. If one could mount the mirror so that it sat slightly lower, it would give the front cam a better field of view past the plastic cover. The most obvious method would be to reorient the two parts of the stalk such that the canted section pointed downwards as opposed to rearwards. I'd suspect that the canted portion is merely formed plastic screwed into the base so reorienting it should be simplistic. Certainly, its design seems to indicate that this would be possible. The other alternative would be to recreate the assembly (either in part in whole) via 3D printing but ideally this should be avoided for obvious reasons. The reason why I'm investigating this is that I'm really keen to get a dashcam plus I really hate the limited view that the OEM mirror provides. A complicating factor is that vehicles in NZ are right hand drive meaning the front cam is further away from the windscreen making the front cover an even bigger obstruction.
After a lot of consideration, I've changed my strategy... Having the mirror slightly lower would reduce the forward cover as an obstruction... Unfortunately, it's increased width (vs the OEM mirror) also means reduced view of the road from the drivers position... Something to be avoided where possible. I note that the replacement mirror projects quite a ways rearwards. If one could move it forwards then this would have the similar effect of reducing the cover as an obstruction. My best solution to this is to redesign a new base for the stalk, moving the attachment point lower & shortening it. 3D printing should make this a simple task. I'll have to wait for both the car & the mirror before I can start attacking this
It's taken a bit and I'm nowhere near finished but I can report on my results. The two piece mounting and stalk supplied with the Nikumaku are both cast metal. After much experimentation, the best solution was to rotate the two parts 180 degrees which results in the mirror mounting lower. Issues with the mounting facing in the wrong direction are easily addressed via a custom 3D printed bracket. This solution surprisingly places the mirror in the exact same place spatially as the original factory fitted mirror. Front camera view is still partially blocked by the cover but it only occupies the top right corner of the screen meaning the full width of the road ahead can be seen albeit only a narrow strip below the obstruction. I have thoughts about building a simple periscope to move the camera viewpoint lower. I designed a neat little housing for the rear camera which optionally can be attached via magnets. My design works well but I do have a gripe about the camera picture. Comparing the camera to a proper rear view mirror, the image appears 2-3 times further away making it a potential hazard if relying on it to pull into traffic. The part of this project that was surprisingly difficult was the electrical fitting. So much so, that I'm still working on it. I'm replacing an autodimming mirror which means there's already power to that location. However the plug/socket arrangement is so unusual that I can't find a third party supplier. Basically it uses 5 pins but with very narrow spacing. I suspect that the solution may be that I'll have to design my own plug to match it (groan). Temporarily I've used the supplied power cable but that's obviously not a long term solution. As mentioned, this is still under action but my expectation is that the autodimming mirror uses 12V and hence that's what's coming out of the car. As the Nikumaku uses 5V, I've sourced a buck converter from AliExpress which outputs via USB. It should then be easy to plug in the relevant USB cable. I've made my work available via Thingiverse for anyone who wants to go down a similar path (www.thingiverse.com/thing:4655894).
@@devilsadvocate2656 I suppose this project is long since completed but if not I was able to find some very thin flat Molex pins that push in from the rear or the mirror connector and sandwich between the plastic of the connector and the installed pin. I've found it quite reliable. I copied the idea from a kit available for powering a V1 radar connector I found on the Valentine web site.
Hello sir . Very good video. One question. What is the total length of wire from the camera mounted at the back of the vehicle to the monitor at the front of the vehicle?
I am buying a rav 4, but this doesn't come in the premium package, which is what I'm buying. We test drove one that had this setup. Could you provide info on what I would have to buy to have this added to my car please.
Hi. Do you have a video or could you make a video installing a Thinkware u1000 for RAV4 both the front and rear? Your skills being shown is deeply appreciated. :-)
The RAV4 has OEM backup camera. There is no need to connect this wire. It can be useful for cars without the backup camera. If you were to connect the mirror to the reverse wire, it would switch to the full image view with parking assist lines every time you switch into reverse.
can you program your garage door opener to be able to replace an OEM mirror capability which would have buttons to allow for adding a garage door signal?
Watching your vids is always dangerous as they usually give me "ideas". I have a RAV4 on order and due for delivery in a couple of months. I'm looking for a suitable dashcam and this certainly makes the mirror based dashcams look more attractive. My only criticism is that in my experience, these mirror based accessories don't support dimming (or in the case of cameras suffer from "flare") when used at night. Some kind of indication of where to buy the product from would also be useful. As someone who makes many items using his 3D printer, it would be simple to design & print a housing for the rear camera or (with a little more work) even manufacture the adaptor mount that adapts the swivel arm to the mirror. Just something to think about
Looked like it’s charging while driving for extended battery when the car is off. Notice the lightning bolt on the battery when powered on, like a cell phone charging
Perfiect, just what I'm looking for. I have one question: does it always record both front and rear at the same time regardless which camera you are viewing? Thx.
Sir! as always I enjoy your narrated videos. Polished and professional. The fact that the mirror installation comes with the OEM mirror mount bracket is great, on the opposite side the fact the mirror requires an 12 to 5 volt adapter isn't. May I know where this was purchased from as I too would like to install this. Thanks
Sir, just for interest the power supply outlet in the cargo area was used for my install and the power cable was just long enough to run along with the camera cable it as it works off accessory too. Thanks again!
Considering my FJ Cruiser displays the reverse camera image on the factory rear view mirror, would I be able to use and power this digital mirror with the stock camera setup?
Yep, here is is. Product Link: NikoMaku Mirror Dash Cam Backup Camera Rear View Mirror Camera Front and Rear 12'' Screen 2K Resolution Full Touch Screen 170° Wide Angle - amzn.to/3HjTApY.
I have 23 rav4 sxe with 360 Birds Eye cam. My rearview mirror has homelink and auto dimming but not the digital camera which is nice when trunk is full of things blocking your view. Could I add this rearview mirror and since the one I have has homelink and auto dimming would it be possible to hook mirror up to that existing wiring and only need wiring across car for camera in trunk. I don't want to hand to do wiring both down the car for power and to back of car for camera too. Is this mirror possible for that
Also does this digital camera mirror have where I can do my garage doors in it like the homelink from Toyota and is it also possible to dim at night for regular mirror
There are a few ways you can run the wires around the air bags. In this video we go over these options: Toyota RAV4 (2019-2022): How To Remove A-Pillar Trim. Will Dash Cam Wire Obstruct Airbag Deployment? - ruclips.net/video/iELCaJRnFwI/видео.html.
Hi! Yes, you can. This mirror comes with the OEM type mounting bracket but there are also other mirrors which simply go on top of the original mirror by using the rubber straps. Similar to how we did it in this video: Toyota RAV4 (2019-2023): GKU D800 - 2.5K Mirror Dashcam With Detached Front Camera - ruclips.net/video/UBdVuIi9ugg/видео.html. Either of these options work in your RAV4.
Здравствуйте, эта модель не имеет сетки обогрева лобового стекла. В кадр попала полимерная точечная аппликация вокруг колпака фронтальной камеры- наносится изготовителем как затемнение от солнца.
Zdrastvuyte posovetuyte mne kakoe zerkolo kupit shtib vsegda bila vkluchina kamera zadnva vida u menya pikap i szadi nichego ni vidno xachu kak shtob rabotal i pakazval xorosho i dnyom i nochyu Spasibo
Здравствуйте Арсен, заочно советовать сложно, всё зависит от дизайна машины и ваших предпочтений. Общий совет- камера заднего вида(ЗВ) должна быть водонепроницаемой. Если видеомонитор уже установлен то любую камеру ЗВ можно "заставить" транслировать картинку постоянно подключением тригер провода к +12 в напрямую или через выключатель. Если устанавливаете цифровое зеркало ЗВ, то по умолчанию оно уже постоянно транслирует ЗВ и дополнительная модификация проводки не нужна. Кроме цифровых зеркал устанавливаемых вместо штатных, есть те которые устанавливаются на переднюю панель, все эти зеркала уже имеют встроенный видеорегистратор. Вот пример: www.amazon.ca/ShiZhen-Streaming-Dashboard-Android-registrator/dp/B07W1PT749/ref=sr_1_65?dchild=1&keywords=rear+view+digital+mirror+recorder&qid=1616716164&sr=8-65
@@MorozovAutomotive moya mashina toyota tundra liftovannaya stsit na doroge visako i s zadi blijayshie 5 -7 metrov nichego ne vidno no etmu xotelas postavit chto nibut na na mesto konkretno shtatnovo zerkalo shtob bilo kak zavatskoe naprimer kak na toyote rav4 ili na highlander 2020 uje est takie s zavoda no na pradaju ix net ya ochen dolgo iskal i nenashol zavotskie toyotvskie zerkata nu vot xatelos bi postavit odin iz etix Sposibo
Here is the video that we made regarding this topic: Toyota RAV4 (2019-2021): How To Remove A-Pillar Trim. Will Dash Cam Wire Obstruct Airbag Deployment? - ruclips.net/video/iELCaJRnFwI/видео.html.
Hey Misbah, here is another video where we installed a different dash cam in the RAV4 using this hole: Toyota RAV4 (2019-2021): Garmin Dash Cam Mini Installation And Footage - ruclips.net/video/FU3EBSKAQAI/видео.html.
![Toyota RAV4: Digital Rear-View Mirror real-life test :: [1001cars]](/img/1.gif)
PRODUCT LINKS:
1. NikoMaku AS5 Pro - 11" 4K Mirror Dashcam With OEM Style Mounting Bracket - amzn.to/3DnxcLf.
2. (Shown In The Video - Discontinued) NikoMaku AS3 Pro - Mirror Dash Cam Backup Camera Rear View Mirror Camera Front and Rear Full Touch Screen 170° Wide Angle - amzn.to/3HjTApY.
RECOMMENDED TOOLS:
1. TRIM REMOVAL TOOL - 4pcs Auto Door Clip Panel Trim Removal Tool Kit - amzn.to/41nYhsk.
2. RATCHETING SCREWDRIVER SET, TORX BIT - Wera Kraftform Kompakt 60 RA Ratcheting Screwdriver Set, 17-Piece - amzn.to/424g1ZY.
3. PRECISION SCREWDRIVERS - Wera - Kraftform Micro Set/12 Pc Sb 1 with Pouch - amzn.to/3KM0ojQ.
4. WIHA HEAVY DUTY SCREWDRIVER SET - Wiha 53097 Screwdriver Set, Slotted and Phillips, Extra Heavy Duty, 7 Piece - amzn.to/3ystzRx.
5. CLIP REMOVAL TOOL - GEARWRENCH Panel Clip Pliers, 3705 - amzn.to/3SjP2Ff.
6. WIRE PULLING LUBRICANT - IDEAL Electrical 31-378 Aqua-Gel® II Electrical Pulling Lubricant - amzn.to/3xZIUZs.
7. DOUBLE-SIDED TAPE - 3M 4910 VHB Double-Sided Tape Mounting Heavy Duty 0.5" x 10Ft - amzn.to/3LtjY4K.
8. [2 Pack] KUNCAN 12V 1FT Car Cigarette Lighter Female Socket Extension Cable, Cigar Cable with Female Socket Connector for GPS/ Dashcam Car Charger - amzn.to/42kvGom.
9. MULTIMETER - Fluke 179 Multimeter with Backlight - amzn.to/3y0mAio.
10. MINI LOW-PROFILE FUSE TAPS - Gebildet 12V-24V Low Profile Add-a-Circuit Fuse Tap, 6 pcs Fuse (3A 5A 7.5A 10A 15A 20A) and Fuse Puller (Pack of 4) - amzn.to/41ZvGde.
11. MALE / FEMALE ELECTRICAL CONNECTORS - TICONN 100 Pcs Nylon Spade Quick Disconnect Connectors Kit - amzn.to/3ZRMUYe.
12. CRIMPING TOOL - TICONN Crimping Tool for Heat Shrink Connectors - Ratcheting Wire Crimper - Crimping Pliers - Ratchet Terminal Crimper - Wire Crimp Tool (30C, Blue) - amzn.to/42je244.
13. GROUND RING TERMINAL - Baomain Ring Ground Insulated Wire Connector Electrical Crimp Terminal 18-22AWG Red RV1.25-4 Pack of 100 - amzn.to/3Ltg77M.
Thanks dude! Just finished installation, going through the rubber tube is a bit tricky but everything else is easy with the help of your video
I just love the mirror!
Nice installation
Cheers for the video, just wondering, do you not need to disconnect the negative terminal on battery before hardwiring camera? And would it be the same in the Hybrid?
Спасибо за ваши видео. очень помогают)
can we get power from dome light panel ? has 12v all the time ?
Did you ever change the power cable instead of plugging into the cigarette lighter?
Very helpful video 😊 how’s the quality of the recording? Are the license plates and other small details clear during playback?
Nice setup, the only thing front camera is not a separate unit, and I’d definitely buy additional dashcam for front recording.
I've been studying this mirror assembly. Compared to the OEM mirror, it sits very close to the roof line when installed. Where the original has a straight stalk, the replacement has a two part canted stalk. If one could mount the mirror so that it sat slightly lower, it would give the front cam a better field of view past the plastic cover.
The most obvious method would be to reorient the two parts of the stalk such that the canted section pointed downwards as opposed to rearwards. I'd suspect that the canted portion is merely formed plastic screwed into the base so reorienting it should be simplistic. Certainly, its design seems to indicate that this would be possible.
The other alternative would be to recreate the assembly (either in part in whole) via 3D printing but ideally this should be avoided for obvious reasons.
The reason why I'm investigating this is that I'm really keen to get a dashcam plus I really hate the limited view that the OEM mirror provides. A complicating factor is that vehicles in NZ are right hand drive meaning the front cam is further away from the windscreen making the front cover an even bigger obstruction.
After a lot of consideration, I've changed my strategy...
Having the mirror slightly lower would reduce the forward cover as an obstruction... Unfortunately, it's increased width (vs the OEM mirror) also means reduced view of the road from the drivers position... Something to be avoided where possible.
I note that the replacement mirror projects quite a ways rearwards. If one could move it forwards then this would have the similar effect of reducing the cover as an obstruction.
My best solution to this is to redesign a new base for the stalk, moving the attachment point lower & shortening it. 3D printing should make this a simple task.
I'll have to wait for both the car & the mirror before I can start attacking this
@@devilsadvocate2656 got an update on this? Maybe do a video if you're gonna go forward with it.
@@reallauradee See my longer reply in this thread.
It's taken a bit and I'm nowhere near finished but I can report on my results.
The two piece mounting and stalk supplied with the Nikumaku are both cast metal. After much experimentation, the best solution was to rotate the two parts 180 degrees which results in the mirror mounting lower. Issues with the mounting facing in the wrong direction are easily addressed via a custom 3D printed bracket.
This solution surprisingly places the mirror in the exact same place spatially as the original factory fitted mirror.
Front camera view is still partially blocked by the cover but it only occupies the top right corner of the screen meaning the full width of the road ahead can be seen albeit only a narrow strip below the obstruction. I have thoughts about building a simple periscope to move the camera viewpoint lower.
I designed a neat little housing for the rear camera which optionally can be attached via magnets. My design works well but I do have a gripe about the camera picture. Comparing the camera to a proper rear view mirror, the image appears 2-3 times further away making it a potential hazard if relying on it to pull into traffic.
The part of this project that was surprisingly difficult was the electrical fitting. So much so, that I'm still working on it. I'm replacing an autodimming mirror which means there's already power to that location. However the plug/socket arrangement is so unusual that I can't find a third party supplier.
Basically it uses 5 pins but with very narrow spacing. I suspect that the solution may be that I'll have to design my own plug to match it (groan).
Temporarily I've used the supplied power cable but that's obviously not a long term solution.
As mentioned, this is still under action but my expectation is that the autodimming mirror uses 12V and hence that's what's coming out of the car. As the Nikumaku uses 5V, I've sourced a buck converter from AliExpress which outputs via USB. It should then be easy to plug in the relevant USB cable.
I've made my work available via Thingiverse for anyone who wants to go down a similar path (www.thingiverse.com/thing:4655894).
@@devilsadvocate2656 I suppose this project is long since completed but if not I was able to find some very thin flat Molex pins that push in from the rear or the mirror connector and sandwich between the plastic of the connector and the installed pin. I've found it quite reliable. I copied the idea from a kit available for powering a V1 radar connector I found on the Valentine web site.
Hello sir . Very good video. One question. What is the total length of wire from the camera mounted at the back of the vehicle to the monitor at the front of the vehicle?
I am buying a rav 4, but this doesn't come in the premium package, which is what I'm buying. We test drove one that had this setup. Could you provide info on what I would have to buy to have this added to my car please.
Hi, the mirror shown in this video is aftermarket. Here is the link - amzn.to/3HjTApY.
Nice! Hows the glare when it's really bright outside? I like that replica A-Team in the background
The glare is there. The way to avoid it is ti tilt the mirror up.
Hi. Do you have a video or could you make a video installing a Thinkware u1000 for RAV4 both the front and rear? Your skills being shown is deeply appreciated. :-)
Hi, thanks for watching. If we manage to get our hands on one, we'll definitely make the installation video.
Is there any reason why you didn't connect the red line, that attached to the rear camera, to the reverse light?
The RAV4 has OEM backup camera. There is no need to connect this wire. It can be useful for cars without the backup camera. If you were to connect the mirror to the reverse wire, it would switch to the full image view with parking assist lines every time you switch into reverse.
Thanks for sharing this. Where did you purchase this from?
amzn.to/3HjTApY
can you program your garage door opener to be able to replace an OEM mirror capability which would have buttons to allow for adding a garage door signal?
Watching your vids is always dangerous as they usually give me "ideas". I have a RAV4 on order and due for delivery in a couple of months. I'm looking for a suitable dashcam and this certainly makes the mirror based dashcams look more attractive. My only criticism is that in my experience, these mirror based accessories don't support dimming (or in the case of cameras suffer from "flare") when used at night.
Some kind of indication of where to buy the product from would also be useful.
As someone who makes many items using his 3D printer, it would be simple to design & print a housing for the rear camera or (with a little more work) even manufacture the adaptor mount that adapts the swivel arm to the mirror. Just something to think about
www.amazon.ca/gp/product/B0897D2S4L/
When car turned off does it still record? If someone break into your car. If so, where it gets electric to power it
Looked like it’s charging while driving for extended battery when the car is off. Notice the lightning bolt on the battery when powered on, like a cell phone charging
So awesome! Do u make these for BMW's? Thanks..
Thanks! Actually we are not making them :). They make them universal. You need to check if your BMW has the same mounting bracket.
@@MorozovAutomotive k great thank you!
Perfiect, just what I'm looking for. I have one question: does it always record both front and rear at the same time regardless which camera you are viewing? Thx.
Yes, it does record both front and rear at the same time, all the time.
Where did you buy the fuse taps? the one I ordered on Amazon were a little high and no clearance on the fuse box.
Gebildet 12V-24V Low Profile Add-a-Circuit Fuse Tap, 6 pcs Fuse (3A 5A 7.5A 10A 15A 20A) and Fuse Puller (Pack of 4) - amzn.to/41ZvGde
Is that the A team behind you?
Sir! as always I enjoy your narrated videos. Polished and professional. The fact that the mirror installation comes with the OEM mirror mount bracket is great, on the opposite side the fact the mirror requires an 12 to 5 volt adapter isn't. May I know where this was purchased from as I too would like to install this.
Thanks
Thank you Carlson! Here is the link - amzn.to/3HjTApY.
Sir, just for interest the power supply outlet in the cargo area was used for my install and the power cable was just long enough to run along with the camera cable it as it works off accessory too.
Thanks again!
Considering my FJ Cruiser displays the reverse camera image on the factory rear view mirror, would I be able to use and power this digital mirror with the stock camera setup?
what is the correct size for the +12V accessory slot - micro, mini or standard? thanks in advance
It is a mini Low Profile
I have the same 12" digital rear view but how to give power from a fuse box to the mirror without the lighter
Do you have a link to the mirror in this video?
Yep, here is is. Product Link: NikoMaku Mirror Dash Cam Backup Camera Rear View Mirror Camera Front and Rear 12'' Screen 2K Resolution Full Touch Screen 170° Wide Angle - amzn.to/3HjTApY.
I have 23 rav4 sxe with 360 Birds Eye cam. My rearview mirror has homelink and auto dimming but not the digital camera which is nice when trunk is full of things blocking your view. Could I add this rearview mirror and since the one I have has homelink and auto dimming would it be possible to hook mirror up to that existing wiring and only need wiring across car for camera in trunk. I don't want to hand to do wiring both down the car for power and to back of car for camera too. Is this mirror possible for that
Also does this digital camera mirror have where I can do my garage doors in it like the homelink from
Toyota and is it also possible to dim at night for regular mirror
Does tucking the wires behind the pillars might block airbags if they want to inflate?
There are a few ways you can run the wires around the air bags. In this video we go over these options: Toyota RAV4 (2019-2022): How To Remove A-Pillar Trim. Will Dash Cam Wire Obstruct Airbag Deployment? - ruclips.net/video/iELCaJRnFwI/видео.html.
Hi! My name is Olga. I have a question. Is it possible to install digital mirror on Toyota RAV4 XLE 2023 ?
Hi! Yes, you can. This mirror comes with the OEM type mounting bracket but there are also other mirrors which simply go on top of the original mirror by using the rubber straps. Similar to how we did it in this video: Toyota RAV4 (2019-2023): GKU D800 - 2.5K Mirror Dashcam With Detached Front Camera - ruclips.net/video/UBdVuIi9ugg/видео.html. Either of these options work in your RAV4.
Where do you buy the digital mirror?
amzn.to/3HjTApY
What is the fuse amp 5/10? used in the fuse adapter cable ?
How much was this mirror and can you leave a link !
amzn.to/3HjTApY
謝謝分享，我在台灣也想做類似的改裝。
別客氣.
Подскажите пожалуйста при просмотре видео файла на большом экране просматривается сетка обогрева на лобовом стекле?
Здравствуйте, эта модель не имеет сетки обогрева лобового стекла. В кадр попала полимерная точечная аппликация вокруг колпака фронтальной камеры- наносится изготовителем как затемнение от солнца.
Your in Burnaby BC! Metrotown
can you make the blinking red dot go away?
You didn’t plug in the red wire for the reverse camera ?
No, since there is a back up camera already installed in the vehicle.
спасибо!
Zdrastvuyte posovetuyte mne kakoe zerkolo kupit shtib vsegda bila vkluchina kamera zadnva vida u menya pikap i szadi nichego ni vidno xachu kak shtob rabotal i pakazval xorosho i dnyom i nochyu
Spasibo
Здравствуйте Арсен, заочно советовать сложно, всё зависит от дизайна машины и ваших предпочтений. Общий совет- камера заднего вида(ЗВ) должна быть водонепроницаемой. Если видеомонитор уже установлен то любую камеру ЗВ можно "заставить" транслировать картинку постоянно подключением тригер провода к +12 в напрямую или через выключатель. Если устанавливаете цифровое зеркало ЗВ, то по умолчанию оно уже постоянно транслирует ЗВ и дополнительная модификация проводки не нужна. Кроме цифровых зеркал устанавливаемых вместо штатных, есть те которые устанавливаются на переднюю панель, все эти зеркала уже имеют встроенный видеорегистратор. Вот пример: www.amazon.ca/ShiZhen-Streaming-Dashboard-Android-registrator/dp/B07W1PT749/ref=sr_1_65?dchild=1&keywords=rear+view+digital+mirror+recorder&qid=1616716164&sr=8-65
@@MorozovAutomotive moya mashina toyota tundra liftovannaya stsit na doroge visako i s zadi blijayshie 5 -7 metrov nichego ne vidno no etmu xotelas postavit chto nibut na na mesto konkretno shtatnovo zerkalo shtob bilo kak zavatskoe naprimer kak na toyote rav4 ili na highlander 2020 uje est takie s zavoda no na pradaju ix net ya ochen dolgo iskal i nenashol zavotskie toyotvskie zerkata nu vot xatelos bi postavit odin iz etix
Sposibo
Hi all, anyone who knows how to activate front camera(top one ) of RAV4 2018 ???
won't your cable block the curtain airbag?
Here is the video that we made regarding this topic: Toyota RAV4 (2019-2021): How To Remove A-Pillar Trim. Will Dash Cam Wire Obstruct Airbag Deployment? - ruclips.net/video/iELCaJRnFwI/видео.html.
You live near Surrey central lol?
doesn't rav4 already comes with digital rear view mirror?
The OEM digital mirror only comes as the add-on. It doesn't come standard.
Здравствуйте. А ссылочку можно где покупали?
amzn.to/3HjTApY
@@MorozovAutomotive Спасибо.
16:38 I have a hole how do I take it up from thier? Please help
Hey Misbah, here is another video where we installed a different dash cam in the RAV4 using this hole: Toyota RAV4 (2019-2021): Garmin Dash Cam Mini Installation And Footage - ruclips.net/video/FU3EBSKAQAI/видео.html.
13:57 whats the clip name ?
Roof headliner clip. Part# 63399-26050.
The problem with this is that if it goes out, for any reason, you’re without a mirror at all.
This mirror does reflect the image similar to the OEM. You can turn off the digital image and use it this way.
@@MorozovAutomotive So it’s similar to the one on the limited?
Yes, it is similar.
Sorry guys, but I didn't like this