Dodge Transmission Swap (Auto to Manual) PT 2

Поделиться
HTML-код
  • Опубликовано: 25 дек 2024

Комментарии •

  • @PeacefulMotoTrailz
    @PeacefulMotoTrailz 11 месяцев назад

    Couldn't have helped more!!!! Thank you so so much!

  • @johndoeed1961
    @johndoeed1961 4 года назад +1

    Awesome info! I plan on swapping my 47re to an nv56 in my 24v 00 3500

  • @yo6669991
    @yo6669991 4 месяца назад

    How are the holes made?

  • @joeponder9668
    @joeponder9668 4 года назад +1

    Short video is better than no video brother!!!

    • @joeponder9668
      @joeponder9668 4 года назад

      Hey bro watching your video, you think pan hard bar is better or easier than 4link? I’m fixing to pop a 1 ton under my 1/2 ton truck and wanna run bags and a valve like you did. Not hauling hella weight on the reg like you do either just a boat here be there. I’m mainly swapping for the disc brakes and 410 gear set. And mine has 350k on it as well.

    • @j_moffitt
      @j_moffitt  4 года назад +1

      Well a parallel 4link will need a panhard as well. A triangulated setup does not need a panhard

  • @j.c.smithprojects
    @j.c.smithprojects 4 года назад +1

    not 1 crack in that dash! little by little she is getting there. combination u-joint available?

    • @j_moffitt
      @j_moffitt  4 года назад

      Can’t have cracks if there isn’t something to crack haha and yes I’ve already got the correct u-joint for the front

  • @gabesmith2016
    @gabesmith2016 Год назад +1

    Approximately how long did this take, hours wise.

    • @j_moffitt
      @j_moffitt  Год назад

      Assuming you have all the parts/equipment needed, 10-15 hrs

  • @shanewright6958
    @shanewright6958 4 года назад +1

    Great job 👍👍🇨🇱

  • @amezyy1713
    @amezyy1713 4 года назад +1

    How was it installing your slave cylinder in the bellhousing I haven’t installed myn yet but it dosent go in all the way Idk if it’s hitting those plastic tabs on the sides or my clutch fork is back to far but it won’t go forward anymore so

    • @j_moffitt
      @j_moffitt  4 года назад

      It’s gonna be under pressure but I managed to get it in far enough to get the bolts on and then snugged it up

  • @scrappydog175
    @scrappydog175 Год назад

    I know I’m late here but can you tell me if a rear drive shaft out of an automatic would fit in the exact same 2nd gen 2500 manual transmission?

    • @j_moffitt
      @j_moffitt  Год назад

      Negative, different lengths and possible to have a different output splines

    • @scrappydog175
      @scrappydog175 Год назад

      @@j_moffitt thank you

  • @TimeAlone8
    @TimeAlone8 6 месяцев назад

    I got a question should I leave my standard 95 long bed alone or do an automatic I’m new to the standard but wanna learn but want to restore the truck to the best condition possible is automatic bad or good for dodges

    • @j_moffitt
      @j_moffitt  6 месяцев назад +1

      Can’t go wrong with a built 47re or 48re

    • @TimeAlone8
      @TimeAlone8 6 месяцев назад

      @@j_moffitt gotcha thank u man may god bless u🙏💯

    • @j_moffitt
      @j_moffitt  6 месяцев назад +1

      Nothing wrong with the 5 speed either, just need to add a 5th gear fix

  • @daytonheath180
    @daytonheath180 2 года назад

    So you can’t use the transfer case from an auto?

    • @j_moffitt
      @j_moffitt  2 года назад

      Different input shaft

  • @Itsa_Mea
    @Itsa_Mea 4 года назад +1

    4:27 Black vacuum line is disconnected

    • @j_moffitt
      @j_moffitt  4 года назад +1

      Yeah I noticed that

    • @Itsa_Mea
      @Itsa_Mea 4 года назад

      @@j_moffitt yeah I wasn't being smart ass, I just thought you missed it because in the video you were saying you had them all hooked up. You have plans on swapping to hydraulic assist for the brakes? My friend has a 95? with vacuum booster brakes I'd like to swap so a video would help.

    • @j_moffitt
      @j_moffitt  4 года назад

      I think one is missing completely but I was referring to the lines around the trans, and no plans for the hydro boost as of now

  • @tedbownas2748
    @tedbownas2748 4 года назад

    Can you borrow the pinion yoke off the other truck?

    • @j_moffitt
      @j_moffitt  4 года назад

      I thought about it but I already got a u joint for it

  • @brandonburkowski5372
    @brandonburkowski5372 3 года назад

    Is the tcase from an auto trans?

  • @juanmanuelcervantes3755
    @juanmanuelcervantes3755 3 года назад

    The transmission must be level ? or how do you figure thanks

    • @j_moffitt
      @j_moffitt  3 года назад

      I don’t understand your question

    • @juanmanuelcervantes3755
      @juanmanuelcervantes3755 3 года назад

      I'm doing the crossmember on 1995 dodge ram 2500 installing the zf6 transmission

    • @j_moffitt
      @j_moffitt  3 года назад

      Pinion angle and the yoke from the transmission should be equal opposites. So if the pinion is a positive 3 degree angle, the trans yoke should be a negative 3 degrees

    • @juanmanuelcervantes3755
      @juanmanuelcervantes3755 3 года назад

      Hey thanks a lot for taking your time to answer my questions thank you buddy