This is EXACTLY what I ran across today! 20 Trax no A/C w ambient sensor codes, literally did everything you did and connector was unplugged under bumper. End of the day was then, I can't wait to go to work tomorrow and do the relearn! I offer you this virtual beer great sir. 🍺
Thanks for this vid. I bought a used Trax that had front end damage that had been repaired. The sensor was missing, and the wires were nowhere to be found. The car lot I bought it from (I assume) literally just cut the wires at that connector on the driver side of the car. Now I just need to splice some wires in and connect a sensor. I would have never found where these wires had been cut without your vid.
Great video! Same issue on a 16 trax, front end damage damaged the wiring harness and sensor replaced both then did the can realearn🧐 (what happened to the OAT update that iv been looking for 2 days for)🤦 Works great now! Thanks!
I would of tested the connectors for power and signal. That would help you speed the process up next time. But I feel you tho bro. Some days it be like that.
Thanks for the sub! There should be plenty of good videos on RUclips showing how to check to see why your fan is not working. It could be a relay a fuse. The fans could be bad also could be wiring.
I had the same problem did all the steps you've done and is still don't blow cold, freon is in, compressor is running, high ac line is hot...what do you think it could be?
This is EXACTLY what I ran across today! 20 Trax no A/C w ambient sensor codes, literally did everything you did and connector was unplugged under bumper. End of the day was then, I can't wait to go to work tomorrow and do the relearn!
I offer you this virtual beer great sir. 🍺
Let me know how it goes
@lakesautomotivediagnostics6509 took me 3 mins to plug bumper up and temp hang it and did procedure. All good!! Ty so much!!
Thanks for this vid. I bought a used Trax that had front end damage that had been repaired. The sensor was missing, and the wires were nowhere to be found. The car lot I bought it from (I assume) literally just cut the wires at that connector on the driver side of the car. Now I just need to splice some wires in and connect a sensor. I would have never found where these wires had been cut without your vid.
Glad it was helpful. Thanks for watching like and subscribe.
Nice catch bro....different functions are hard to find depending on the scan tool, so luckily it work out..
Yeah, I had a little wasted time but least I got it figured out
Great video! Same issue on a 16 trax, front end damage damaged the wiring harness and sensor replaced both then did the can realearn🧐 (what happened to the OAT update that iv been looking for 2 days for)🤦
Works great now!
Thanks!
Nice work!
I would of tested the connectors for power and signal. That would help you speed the process up next time. But I feel you tho bro. Some days it be like that.
🔧✌️🔧
Awesome video Brotha!! I am sure that will help all of us techs out here!!
It cost me a couple hours, definitely the first time I have seen that, thanks for watching. Hope you have a great day.
Thank you! I'm subscribed to you. I need one to show why the radiator fan doesn't engage 😞
Thanks for the sub! There should be plenty of good videos on RUclips showing how to check to see why your fan is not working. It could be a relay a fuse. The fans could be bad also could be wiring.
Great job man...only a scan tool do this calibration can bus data?
Yes, that was the first time I have ever seen a can bus calibration. Thanks for watching
I had the same problem did all the steps you've done and is still don't blow cold, freon is in, compressor is running, high ac line is hot...what do you think it could be?
Did you evacuate the AC system and recharge with the correct amount?
@@lakesautomotivediagnostics6509 yes
Did you have any codes and what was your AC high and low pressure
@@lakesautomotivediagnostics6509 no
Mine have the same problem