Sir RC TRANSMITAR H JO IC H12D, H12E, L293D, 7805 Transistor s Bana h sir iss se motar ko 5volt out put milta h jiss s motar ghumta h sir, RC transmitar k 5volt out put ko 12volt output kaise kre JIS se motar high speed s ghum ske
Thanks for your clearly explanation But I have a question. If I can use a lora module for more rang.. And what is best module that provides less time delay
Brother i can not understand the s1 to s7 connectors or header pin purpose. please explain this. And if i attach a coreless motor with j1 header then dose it works??
Can you please make one more transmitter and receiver but of 14 channel. Bro please make it we all are supporting you . Please please please . This was very nice and beautifully made . Your videos are awesome . Please make it
Your Gerber is in error !! In the transmitter 5 volts it only arrives in the regulator 3v3. If using the AMS1117 3.3 you do not need the 1K resistor. The 10K resistor is also missing from the processor reset, both from the transmitter and the receiver. Whoever orders the plates will see that they do not work.
How to setup Elevon Mixing (channel 1 + channel 2) for delta wing plane like f22 rapter,delta wing?? plz reply my question answer 🥲 in this transmeter and reciver
hello, thanks for this video i made the transmitter and receiver and their is a connection between them but i have a problem no channel on the receiver is resetting to 0 for example if i connect a led to a potentiometer CH the led doesn't turn off if the potentiometer is all the way down but i can increase the brightness of the led when i move the potentiometer up even servos don't move or the motor on esc ,i can control the throttle but not turn it completely off. the same happen with switches can't turn of a led but can increase brightness of led when turned on. please if you have any idea tell me thanks in advanced :)
Hello, I like your project, but since I am a beginner, I would like to ask. I need not only to send, but also to receive battery status data from the receiver. Unfortunately, I can't adjust the program to make it work. Can you please advise?
Hi. I wonder can you help me. I have a parrot skycontroller for my drone. It is a wifi controller. The function for up down has stopped working. Controller connects to the drone and all other functions work. I can only assume the control chip in the joystick is gone bad. Where might I find a new chip to replace this? Parrot are of no help to me on this.
Hey , I have already made it few days back but throttle joy stick is little tricky, did you modify it ? I have excluded spring so It can stays in same position.
this is good work. can you kindly share your schematic diagrams sir. and if possible your code fro this demostration . the link in the description is broken i guess. thank you
Sir i am havin a rc brushed motor mini quadcopter and i lost the tx, the drone is build with stm32f031k4 chip with xn297l radio chip, so i want to control that drone with ur diy tx, is it possible?
Hello bro mai ek wireless car project banana hai usme mai transmitter recieved use karna hai càr mai jo remote se nai phone ya kahi se bhi matlab satelite control ho sake meri help kro 🙏yeh tiyar karne mai
Sir aap ne hindi me samjhaya hota to sabka bhla hota bhai OK sir 5 Jul 2018 ka video me jo heat sencer he us ka aqchul neam kiya he or kaha milega sir pliz Ripley mi pliz and aap ka Watsapp no pliz sir description me dijey
Brother I have a big problem, my esc and servos connected to it also start moving when I shake the receiver can you please solve my problem what may be the cause for it some times when I shake the receiver or just move it the servos and motor just start moving even when the transmitter is off
I was trying using nrf24l01 module with arduino, but could not communicate between two nrf24l01 module. Please make a video to live demonstrate how to use nrf module with arduino mega/nano from very begining level
@@rc3d490 aliexpress has the joysticks which have center as the 0 position which does not provide the full range of throttle . so that is the one i am asking for
![Noob To Max With DRAGON REWORK In Blox Fruits [FULL MOVIE]](http://i.ytimg.com/vi/LnBMOinoOvA/mqdefault.jpg)
I don't know why people do not view this videos...awesomee👍👍👍
My dear, for watching only video, this video is perfect. But for implementing its not good. You should explain the parts also. All parts.
@Internet Gamer'z 360 that’s not an explanation, its a list
don't talk like idiot
Excellent project. But I'm unable to download the schematic diagram, it's not found!
What rf module will be use if want to increase the range and libe streaming camera also
Next episode
Can you plz provide rotary encoder switch link and which type of rotary switch we have to take plz replay Asap......,Thank you
From which state you are
Sir RC TRANSMITAR H JO IC H12D, H12E, L293D, 7805 Transistor s Bana h sir iss se motar ko 5volt out put milta h jiss s motar ghumta h sir, RC transmitar k 5volt out put ko 12volt output kaise kre JIS se motar high speed s ghum ske
Kitna distance cover kr skta hai yeh drone.. Aur age range increase krna hoga to kya krna hoga. Yeh bhi batiye na..
Atmega 328 p sm ke uper jo ic attach hi uska name btaiye aap
Ams 1117 ke bat kar rahe ho app??
Thanks for your clearly explanation
But I have a question. If I can use a lora module for more rang.. And what is best module that provides less time delay
Can we use this reciever for brushed motor drone
Please reply
No
What changes should I make on the reciever for making brushed motor to work
yes
Google drive link is not working bro
Plz help me with it 🙏
We can't make make using NRF24L01 because there are some issues with range.
If you make it perfectly then there is no issue
@@EtDiscover NRF are good for RC boats cars but in case of planes if planes go out of range there will be a crach.
Brother i can not understand the s1 to s7 connectors or header pin purpose. please explain this. And if i attach a coreless motor with j1 header then dose it works??
This receiver only for brushless motor Not coreless , This Receiver just produce sense
What should i use from ur list provided in description if i want to make only 4 channel transmitter nd reciever ?
brother your pcb pdf link is not opening please tell me another way
If I make this then do I will need KK flight controller to control drone?
Can you please make one more transmitter and receiver but of 14 channel. Bro please make it we all are supporting you . Please please please . This was very nice and beautifully made . Your videos are awesome . Please make it
Your Gerber is in error !!
In the transmitter 5 volts it only arrives in the regulator 3v3.
If using the AMS1117 3.3 you do not need the 1K resistor.
The 10K resistor is also missing from the processor reset, both from the transmitter and the receiver.
Whoever orders the plates will see that they do not work.
How to setup Elevon Mixing (channel 1 + channel 2) for delta wing plane like f22 rapter,delta wing??
plz reply my question answer
🥲 in this transmeter and reciver
Please tell me all over total budget for this project
how to program IC without ur that programming device
You can using Arduino uno nano as you want
@@EtDiscover how
Bro AAP bressles motar bna sakte ho
If I use this for making a quadocopter then I have to solder the accelerometer on the transmitter board???? Am I right ?
Sir me 2 remote Banana chata हू... To kya 1 transmiter se 2 receiver nhi chalege.. Na???
Code me kuch changes karna padega kya.. ❓
Which camera you used to make videos
Hi, sir in this drone use camera to fit this option is available
hello, thanks for this video i made the transmitter and receiver and their is a connection between them but i have a problem no channel on the receiver is resetting to 0 for example if i connect a led to a potentiometer CH the led doesn't turn off if the potentiometer is all the way down but i can increase the brightness of the led when i move the potentiometer up even servos don't move or the motor on esc ,i can control the throttle but not turn it completely off. the same happen with switches can't turn of a led but can increase brightness of led when turned on. please if you have any idea tell me
thanks in advanced :)
please describe about the "rotary encoder"(sw1) in your ckt. where you have placed the potentiometer....can you give a link for the potentiometer?
Hello, I like your project, but since I am a beginner, I would like to ask. I need not only to send, but also to receive battery status data from the receiver. Unfortunately, I can't adjust the program to make it work. Can you please advise?
My nrf24l01 attena module is not working properly .please give me suggestions 🙏🏻🙏🏻
Can we use it as flight control board for brushless motor drone
Hi. I wonder can you help me. I have a parrot skycontroller for my drone. It is a wifi controller. The function for up down has stopped working. Controller connects to the drone and all other functions work. I can only assume the control chip in the joystick is gone bad. Where might I find a new chip to replace this? Parrot are of no help to me on this.
What should you do with these diy projects after making these projects
can you tell me about this
Please sir tell me where is it possible for me to dtmf and 2 mobile phones and use it as reciver and transmitter
Nice vedio ...Mai bhi aisa hi project banaya hu
Hey , I have already made it few days back but throttle joy stick is little tricky, did you modify it ? I have excluded spring so It can stays in same position.
You need to change Value of millisecond
preet charan what will I have to study to make this mu higher education
@@parshvapatel8484 degree in electronics
Excuse me ....can you tell me which couse did you study to know about all this stuff
this is good work. can you kindly share your schematic diagrams sir. and if possible your code fro this demostration . the link in the description is broken i guess. thank you
I want to make one but I am making PCB at home and when I create schematic ,and tries to convert in PCB it says incomplete nets. Please help.
How can i make it
How to make circuit diagram
Sir your google drive link is not working please provide me a correct link i am also making a drone so i need this Tx and Rx
I like to use transmitter control via Bluetooth control in mobile, what type of board can I use, please give a good suggestion.
Which programmer modules did you use please?
Cant you provide any circuit diagram for transmitter and receiver??
Sir where can we get the programming?
Can u make a racing drone using this transmitter and receiver
Excellent work!!!
Hi, how did you modify the joystick potentiometers? Thank you!
Coba test jarak maksimal berapa meter...?
Please explain the programming part with normal arudino not your homemade
Sir please make a rc car and interface this remote contoller with it.
Can we program ic with arduino uno ic socket by change this ic plzz tell
Can we use a coreless motor in this
Bro your transmitter and receiver code which you have put in the description is not opening so what should i do
I have only Arduino uno board can I directly connect it with transmitter for uploading the code .
If yes then how?
Hey bro what is the menziles? This transmitter
What are the 2 pin male header on the receiver for?
Sir i am havin a rc brushed motor mini quadcopter and i lost the tx, the drone is build with stm32f031k4 chip with xn297l radio chip, so i want to control that drone with ur diy tx, is it possible?
How much volt did you used for reciver can we use 3.7v
Can u make same concept for camera input and output purpose
Sir, what is the range of trancmiter and riciver
Can i program microcontroller ic using arduino
You can
Pls give information about all the components of receiver boarx
Can we increase the range and the no. Of channels??
Ap kahrahe the next video is mppt ki hoge
Hlo i cant order pcb using jlc pcb because i am from india
Can you plzz give me the link of desired transmitter and receiver pcb board which you have asked from jlcpcb ..
where you got that components pls give me link
How did you solder?
How did u do that yo your joystick
Bhai kitne door travel travel kr skta hai drone range kya hai...
1,2Km
Hello bro mai ek wireless car project banana hai usme mai transmitter recieved use karna hai càr mai jo remote se nai phone ya kahi se bhi matlab satelite control ho sake meri help kro 🙏yeh tiyar karne mai
Hello. what is the encoder on the board used for? . can you order a stepper motor?
Is this transmitter compatible with Whoop Lite F3 Mini brushed flight controller
Sir aap ne hindi me samjhaya hota to sabka bhla hota bhai
OK sir 5 Jul 2018 ka video me jo heat sencer he us ka aqchul neam kiya he or kaha milega sir pliz Ripley mi pliz and aap ka Watsapp no pliz sir description me dijey
Me already hindi channel kohl chuka, link description me he ap subscribe kar sakte ho, or konsa video me samajh nehi paya please uske nam batado
@@EtDiscover total cost??
How to make a electronic robot which operates the programic logic command.please basic training in robotics video.
Can this work with unchangeable batteries ? Please reply
How to make ppm or sbus reciever
Coming soon, next video
Thanks for replying 😀
can this be made with STM 32? STM 32 has better ADC resolution
bro i want to learn electronics of your level what should i do..which course..
I make a separate video for this please wait
@@EtDiscover ok bro.Tq
Brother I have a big problem, my esc and servos connected to it also start moving when I shake the receiver can you please solve my problem what may be the cause for it some times when I shake the receiver or just move it the servos and motor just start moving even when the transmitter is off
Plz make a channel mixing (2 servo) ( channel 1 + channel 2) module circuit
I was trying using nrf24l01 module with arduino, but could not communicate between two nrf24l01 module.
Please make a video to live demonstrate how to use nrf module with arduino mega/nano from very begining level
We can upload program using arduino?
In ic ur shown in video
Yes you can
@@EtDiscover thank you Buddy
Welcome
can you pleas tell us how to configure mpu-6050 3 axis module in this transmiter to controol drone
Sir , circuit diagram link not opening,give me circuit diagram plz
Please how can I get all the exact electrical Components for the project such as capacitor resistors
GERBER file is not accessible. Can you provide a valid link? link in the description is not working.
Do you have video for tracking devices?
extra two switch ka use kyon kiya tha koi btado
Wait… you’re offering the gerber files for free?? Bro you are my hero. I’ll donate to you In a little while. Ty so much.
Hi dear apne mppt project nahe banae?
Can we use it in raspberry pi if yes plz make a video
Nice comment
@@EtDiscover bro i am asking what do you mean by nyc comment
I like your comment so that’s why I told you don’t mind bro, I will try to make your video,
Bro where did you buy all this stuff in kolkata....?? Can you share Shop location.....it would be helpful...
haque electronics kolkata
@@EtDiscover chandni chowk.....???
Yes
please make a drone with this
Exactly, please make a drone with Arduino flight control and this transmitter and receiver
from where do i buy that type of joystick
AliExpress
@@rc3d490 aliexpress has the joysticks which have center as the 0 position which does not provide the full range of throttle . so that is the one i am asking for
Amazon the purchase link is in the description box
Please bro please make it clear that how we will program the transmitter and receiver
Sir what is the range of this
Tx and rx
Where can i buy it? Can i get from International shop