hello friend. thank you very much for this videos. these were really helpful. I have a ps3 motherboard with the same sympthoms. thank to your videos I found a resistance giving 0 OHM value, around the IDT 9277BNLG chip, the one you went to check first after trying the mosfets. I will try to reflow it and see if hopefully it fixes it. Greetings from Argentina.
When using a heat gun for reflowing solder, it's crucial to set the correct temperature and apply heat for the appropriate amount of time to avoid damaging the components. you should set your heat gun to 350°C to 400°C (660°F to 750°F). This range is commonly used for leaded and lead-free solder. The heating time can vary depending on the size and type of the component. For a typical reflow on a chip, aim for 30 seconds to 1 minute of consistent heat application. Move the heat gun in a circular motion around the component to ensure even heating and to avoid scorching any one area. Start by gently heating the surrounding area before focusing directly on the component to reduce the risk of thermal shock. Use Flux: Applying flux beforehand can help the solder flow more smoothly and evenly. Watch closely for the solder to start flowing, which is a sign it's reached the right temperature. Be careful not to overheat the component, as too much heat can damage both the solder and the board. If you need more detailed advice, feel free to ask!
@idreestech I have the same problem that is shown in the video, a resistor is reading at 55 ohms, but when I'm using the heat gun, it is not melting the solder. I have the temperature set to 350 degrees celsius and I added solder flux as well and nothing is happening. Do you know what I'm doing wrong?
Can you teach how to use XY mode on osciloscope? The motherboard must have voltage to measure that? Or it's like ones ohms reading? How many problems you connect? 2 ? How you do to not connecting gnd wire one the problems ? Thanks... Greatings from Portugal 🇵🇹 🌟
My friend Idris, I am a beginner in maintaining consoles. Are there plans for the main check points that we can benefit from, or do you make a video dedicated to the main check points for each device?
@@idreestech I have been following up for two days, thanks for your credibility in the work. I hope that there will be a clearer camera and that it will be close to the places where electronic parts are examined. I was impressed by your credibility in transmitting information
hello my friend, greetings from turkey My 4204A Super Slim console has the same issue. it was caused by the socket I plugged in, there was a sound from the socket and my console turned off and turned on a red light. The console sometimes opens without any outside intervention, so opening it by applying pressure does not work in this console. When the console is opened, I can use it without any problems as before. Trying a new psu didn't solve my problem, what should I do to fix the console?
Sir mera ps3 fat model hai pehlay jab on krta tha to red light on hoti thi phir green bhi on hokay band hojati thi lekin ab bilkul power bhi nhi dy rahi hai matlab k no lights is ka koi solution hai?
It sounds like your PS3 is experiencing intermittent power issues, which could be caused by a few different factors. Here are some potential reasons and solutions: Replace Thermal Paste: If your PS3 is overheating, replacing the thermal paste on the CPU and GPU can help. Check Power Supply: If you have another PS3 power supply or can find a replacement, try swapping it out to see if the problem is resolved. If you need more detailed help with any of these steps, feel free to ask!
@@idreestech How are you, my brother? We, as followers of your honor, learn from you the maintenance of console devices. As beginners, there must be contact with you other than RUclips directly, so that we can refer to your experience in practical application if there is any problem.
hello friend. thank you very much for this videos. these were really helpful. I have a ps3 motherboard with the same sympthoms. thank to your videos I found a resistance giving 0 OHM value, around the IDT 9277BNLG chip, the one you went to check first after trying the mosfets. I will try to reflow it and see if hopefully it fixes it. Greetings from Argentina.
I appreciate your feelings.
What temperature did you set your heat gun to, and how long does it normally take to heat up the solder for the reflow?
When using a heat gun for reflowing solder, it's crucial to set the correct temperature and apply heat for the appropriate amount of time to avoid damaging the components.
you should set your heat gun to 350°C to 400°C (660°F to 750°F). This range is commonly used for leaded and lead-free solder.
The heating time can vary depending on the size and type of the component. For a typical reflow on a chip, aim for 30 seconds to 1 minute of consistent heat application. Move the heat gun in a circular motion around the component to ensure even heating and to avoid scorching any one area.
Start by gently heating the surrounding area before focusing directly on the component to reduce the risk of thermal shock.
Use Flux: Applying flux beforehand can help the solder flow more smoothly and evenly.
Watch closely for the solder to start flowing, which is a sign it's reached the right temperature.
Be careful not to overheat the component, as too much heat can damage both the solder and the board. If you need more detailed advice, feel free to ask!
@idreestech thank you, I'll definitely ask you if I have any questions, you're very helpful
@idreestech I have the same problem that is shown in the video, a resistor is reading at 55 ohms, but when I'm using the heat gun, it is not melting the solder. I have the temperature set to 350 degrees celsius and I added solder flux as well and nothing is happening. Do you know what I'm doing wrong?
Dude... someone is snoring big time, while you busy working and trying to teach us. But thank you 🙏🙏
Sorry about that dear.
Can you teach how to use XY mode on osciloscope? The motherboard must have voltage to measure that? Or it's like ones ohms reading? How many problems you connect? 2 ? How you do to not connecting gnd wire one the problems ? Thanks... Greatings from Portugal 🇵🇹 🌟
Yes I can
@@idreestech thanks very much... ;)
My friend Idris, I am a beginner in maintaining consoles. Are there plans for the main check points that we can benefit from, or do you make a video dedicated to the main check points for each device?
All of my videos are for the same aspect.
@@idreestech I have been following up for two days, thanks for your credibility in the work. I hope that there will be a clearer camera and that it will be close to the places where electronic parts are examined. I was impressed by your credibility in transmitting information
You can start your apprenticeship with me.
قريبا سيكون في HD.
@@عمارالراجح قريبا سيكون في HD.
Mash Allah
Hum saray circuits simple meter sa chck ker sakty han kya?
You can compare component readings with the negative probe connected to GND. To do this, you need another functional motherboard for comparison.
hello my friend, greetings from turkey My 4204A Super Slim console has the same issue. it was caused by the socket I plugged in, there was a sound from the socket and my console turned off and turned on a red light. The console sometimes opens without any outside intervention, so opening it by applying pressure does not work in this console. When the console is opened, I can use it without any problems as before. Trying a new psu didn't solve my problem, what should I do to fix the console?
Probably the motherboard
Sir have you any course
Hello king, if you put the recently spread ps4 jailbreak method from update A to update B, you will be at the top
Thank you for sharing.
My pleasure!
Sir mera ps3 fat model hai pehlay jab on krta tha to red light on hoti thi phir green bhi on hokay band hojati thi
lekin ab bilkul power bhi nhi dy rahi hai matlab k no lights is ka koi solution hai?
Do you have tools?
@@idreestech yes poora box hai tools ka
Maybe, you could come to some solutions by watching my other videos.
@@idreestech sir agr mein ap ko apna ps3 repairing k liye TCS kro to ap repair kry gay ?
@@Abdullaah3015 I can try.
reflowing the resistance just temporary solves the problem?
Yes, right.
For perma replace it.
Masha Allah great work thanks to you Sir
It's my pleasure
@@idreestechWhat was the problem?
Great job
Sir i have same issue in my ps3 what kind i do??
If this video did not help, watch other related to the error.
Sir Mine Is PQX 001 MOTHERBOARD BUT I HAVE NO DIAGRAM HOW TO DO IT
Model CECH 4201B PLS HELP kindly
You in Liberia
I am in Pakistan.
Thanx master ❤️🇹🇷
please Sir how to check Dual DC-to-DC converter chip ps3 super slim
It has 1.8-volt input and two 1.00 and 1.2-volt outputs on the other side. Feedback coupling resistances are at 55 and 90 ohms.
@@idreestech thanks
my hdd died now its doing power off thing
My ps3 is on and off 😢😢
It sounds like your PS3 is experiencing intermittent power issues, which could be caused by a few different factors. Here are some potential reasons and solutions:
Replace Thermal Paste: If your PS3 is overheating, replacing the thermal paste on the CPU and GPU can help.
Check Power Supply: If you have another PS3 power supply or can find a replacement, try swapping it out to see if the problem is resolved.
If you need more detailed help with any of these steps, feel free to ask!
thank you
Welcome!
Good
😉
Thanks 😋
And if you have a Telegram group to communicate and benefit from your presence and experience in tracking malfunctions
How?
@@idreestech How are you, my brother? We, as followers of your honor, learn from you the maintenance of console devices. As beginners, there must be contact with you other than RUclips directly, so that we can refer to your experience in practical application if there is any problem.
@@idreestech Of course, it will be a closed group for a number you specify, and this is all with the balance of your work, God willing
@@عمارالراجح Please let me know what you want
I still don't understand what you are asking me and what you want from me?
My ps3 Hen sometimes shut down it self with no red light on,after i turn on again and it work good for many hours.
Reinstall.
Brother
Sir
Se escucha alguien roncando 🙄
Hahhah, la dueña de la misma máquina está durmiendo.
Sir bht urgent kam hy ap sy or kafi din sy ap ka number b off hy Whatsapp b band please whatsapp check kry
Give your whatsapp sir???
Check channel description.